Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A driver moving at 36 km/h sees an obstacle. Her reaction time is 0.6 s, after which the car brakes with a constant deceleration of 4 m/s². Find the total stopping distance d from the moment she sees the obstacle.
v₀ = 36 km/htr = 0.6 sa = −4 m/s²
d = m
2.KinematicsHard
Ball A is dropped from rest from a height of 10 m. At the same instant ball B is thrown straight up from the ground directly below at 10 m/s. Ignore air resistance and use g = 9.81 m/s². When do the balls meet? Find t.
H = 10 mv0B = 10 m/sg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
Masses of 7.5 kg and 6 kg hang on either side of a light, frictionless pulley, connected by a light string. The system is released from rest. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 7.5 kgm2 = 6 kgg = 9.81 m/s²
T = N
4.Newton’s lawsHard
An 8.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 3.5 kg mass. The coefficient of kinetic friction between block and table is 0.2. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 8.5 kgm2 = 3.5 kgμ = 0.2g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 20° above horizontal from level ground. Ignore air resistance. Find the maximum height H the ball reaches.
v0 = 40 m/sθ = 20°g = 9.81 m/s²
H = m
6.Projectile motionHard
A ball is launched at 50° above horizontal from the top of a 5 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 15 m/sθ = 50°h = 5 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A 4 kg block slides 5 m down a slope at 45° to the horizontal, with a coefficient of kinetic friction of 0.15. Find the work Wf done against friction.
m = 4 kgθ = 45°μ = 0.15d = 5 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 1 kg cart is released from rest at a height of 22.5 m on a smooth track that leads into a vertical circular loop of radius 5 m. Find the normal force N the track exerts on the cart at the top of the loop.
m = 1 kgh = 22.5 mR = 5 mg = 9.81 m/s²
N = N
9.Momentum & collisionsMedium
A 12 g bullet is fired horizontally into a 1 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 8 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 12 gM = 1 kgh = 8 cmg = 9.81 m/s²
v = m/s
10.Momentum & collisionsHard
A 5 g bullet is fired horizontally into a 4 kg block hanging from light strings 0.9 m long, and stays in it. The strings swing out to a largest angle of 35° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 5 gM = 4 kgL = 0.9 mθ = 35°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1 m wide sits in the wall of a tank of glycerin, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal venturi meter with an inlet diameter of 100 mm and a throat diameter of 50 mm. The pressure at the inlet is 27 kPa higher than at the throat. Ignoring losses, find the flow rate Q.
A closed water tank has compressed air above the water at a gauge pressure of 190 kPa. Water leaves through an opening with a diameter of 20 mm, 5 m below the water surface, into the open air. Ignoring losses, find the jet velocity v. Use g = 9.81 m/s².
A heat engine works between a hot reservoir at 300 °C and a cold reservoir at 15 °C. It takes in 4600 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 300 °CTL = 15 °CQH = 4600 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A heat pump delivers 7.5 kW of heat to a heating system at 45 °C, taking heat from a source at -10 °C. Its actual COP is 55% of the Carnot COP between these temperatures. Find the electrical power Ẇ it uses.
TH = 45 °CTL = -10 °CηII = 55%Q̇H = 7.5 kW
Ẇ = kW
19.Waves, sound & opticsMedium
A source of 400 Hz moves at 20 m/s towards a stationary observer. The speed of sound is 343 m/s. Find the frequency f′ that the observer hears.
f = 400 Hzv = 343 m/svs = 20 m/s
f′ = Hz
20.Waves, sound & opticsHard
An optical fibre has a core with n₁ = 1.5 and a cladding with n₂ = 1.4. Find the largest angle θa to the fibre axis at which light from air can enter the end of the fibre and still be guided by total internal reflection.
n1 = 1.5n2 = 1.4n0 = 1.00
θa = °
3Solutions
1.Kinematics
Answer: d = 18.5 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 36/3.6 = 10 m/s
Reaction distance
d1 = v₀·tr = 10·0.6 = 6 m
Braking distance
d2 = v₀²/(2a) = 10²/(2·4) = 12.5 m
Total
d = 6 + 12.5 = 18.5 m
Answer
d = 18.5 m
2.Kinematics
Answer: t = 1 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Meeting time
Up is positive, the ground is y = 0.
10 − ½g·t² = 10·t − ½g·t² → t = 10/10 = 1 s
Answer
t = 1 s
3.Newton’s laws
Answer: T = 65.4 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Acceleration
The net driving force is the difference of the weights; it moves the total mass.
a = (7.5 − 6)·9.81/(7.5 + 6) = 1.09 m/s²
Tension from the lighter mass
T − m2·g = m2·a → T = 6·(9.81 + 1.09) = 65.4 N
Answer
T = 65.4 N
4.Newton’s laws
Answer: a = 1.471 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 40·cos 20° = 37.59 m/s
vy = v0·sin θ = 40·sin 20° = 13.68 m/s
Highest point
At the top the vertical velocity is zero: vy² = 2gH.
H = vy²/(2g) = 13.68²/(2·9.81) = 9.539 m
Answer
H = 9.539 m
6.Projectile motion
Answer: t = 2.718 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 15·cos 50° = 9.642 m/s
vy = v0·sin θ = 15·sin 50° = 11.49 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 5 + 11.49·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (11.49 + √(132 + 98.1))/9.81 = 2.718 s
Answer
t = 2.718 s
7.Work & energy
Answer: Wf = 20.81 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 39.24·0.7071 = 27.75 N
F = μN = 0.15·27.75 = 4.162 N
Work against friction
Wf = F·d = 4.162·5 = 20.81 J
Answer
Wf = 20.81 J
8.Work & energy
Answer: N = 39.24 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
The cart just makes it round when h = 2.5R; then N = 0 at the top.
9.Momentum & collisions
Answer: v = 105.7 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Swing after impact
V = √(2·g·h) = √(2·9.81·0.08) = 1.253 m/s
Collision
m·v = (m + M)·V → v = (0.012 + 1)·1.253/0.012 = 105.7 m/s
Answer
v = 105.7 m/s
10.Momentum & collisions
Answer: v = 1431 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 0.9·(1 − cos 35°) = 0.1628 m
Speed after impact
V = √(2·9.81·0.1628) = 1.787 m/s
Collision
v = (m + M)·V/m = 4.005·1.787/0.005 = 1431 m/s
Answer
v = 1431 m/s
11.Hydrostatic force
Answer: F = 29.43 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 1/2 = 1 m
A = H·b = 1·3 = 3 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·1·3 = 29.43 kN
Answer
F = 29.43 kN
12.Hydrostatic force
Answer: F = 50.99 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 1.5/2 = 2.75 m
A = H·b = 1.5·1 = 1.5 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·2.75·1.5 = 50.99 kN
Answer
F = 50.99 kN
13.Continuity & Bernoulli
Answer: Q = 14.9 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity
v1 = v2·(50/100)² = 0.25·v2
Bernoulli between inlet and throat
The pipe is horizontal, so only pressure and velocity change.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Bernoulli from the surface to the jet
v = √(2·(190000/1000 + 9.81·5)) = 21.87 m/s
Answer
v = 21.87 m/s
15.Ideal gas law
Answer: V = 294.1 L
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = 340/4.003 = 84.94 mol
T = 60 + 273.15 = 333.1 K
Volume
V = nRT/P = 84.94·8.314·333.1/800 = 294.1 L
Answer
V = 294.1 L
16.Ideal gas law
Answer: V2 = 11.85 L
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 293.1 K, T2 = 463.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 20·(300/800)·(463.1/293.1) = 11.85 L
Answer
V2 = 11.85 L
17.Heat engines & refrigerators
Answer: Wmax = 2287 kJ
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 300 + 273.15 = 573.1 K
TL = 15 + 273.15 = 288.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 288.1/573.1 = 49.73 %
Maximum work
Wmax = ηmax·QH = 0.4973·4600 = 2287 kJ
Answer
Wmax = 2287 kJ
18.Heat engines & refrigerators
Answer: Ẇ = 2.357 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 45 + 273.15 = 318.1 K
TL = -10 + 273.15 = 263.1 K
Carnot and actual COP
COPmax = 318.1/(318.1 − 263.1) = 5.785
COP = 0.55·5.785 = 3.181
Power input
Ẇ = Q̇H/COP = 7.5/3.181 = 2.357 kW
Answer
Ẇ = 2.357 kW
19.Waves, sound & optics
Answer: f′ = 424.8 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.