Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 90 km/h brakes with a constant deceleration of 8 m/s² until it stops. How long does braking take? Find t.
v₀ = 90 km/ha = −8 m/s²v = 0
t = s
2.KinematicsHard
A ball is thrown straight up at 9 m/s from the edge of a roof 30 m above the ground. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax above the ground.
v₀ = 9 m/sh₀ = 30 mg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A box slides across a level floor with an initial speed of 3 m/s and comes to rest after 3.1 m. Use g = 9.81 m/s². Find the coefficient of kinetic friction μ.
v₀ = 3 m/sd = 3.1 mg = 9.81 m/s²
μ =
4.Newton’s lawsHard
A 1.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 4.5 kg mass. The coefficient of kinetic friction between block and table is 0.25. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 1.5 kgm2 = 4.5 kgμ = 0.25g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched from level ground at 50° above the horizontal and lands 20 m away. Ignore air resistance and use g = 9.81 m/s². Find the launch speed v0.
θ = 50°R = 20 mg = 9.81 m/s²
v0 = m/s
6.Projectile motionHard
A ball is launched at 15° above horizontal from the top of a 35 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 22 m/sθ = 15°h = 35 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A 1200 kg car drives up a 5° slope at a constant 90 km/h. Air resistance and rolling resistance together amount to 750 N. Find the power P the wheels must deliver, in kW.
A 1 kg block is released from rest at height 5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 3.5 m long (μ = 0.2) and then runs onto a spring (k = 5000 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
m = 1 kgh = 5 mL = 3.5 mμ = 0.2k = 5000 N/mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 2.5 kg glider moving at 7 m/s makes a perfectly elastic head-on collision with a 4 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 2.5 kgm2 = 4 kgv1 = 7 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
A 0.2 kg ball hits a wall at 23 m/s and bounces straight back at 12 m/s. The contact lasts 25 ms. Find the average force Favg of the wall on the ball.
m = 0.2 kgvin = 23 m/svout = 12 m/sΔt = 25 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 0.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows through a horizontal venturi meter with an inlet diameter of 100 mm and a throat diameter of 60 mm. The pressure at the inlet is 36 kPa higher than at the throat. Ignoring losses, find the flow rate Q.
A fountain nozzle points straight up. Just below the nozzle the supply pipe has a diameter of 75 mm and a gauge pressure of 70 kPa. The nozzle exit diameter is 20 mm, and the height difference across the nozzle is negligible. Ignoring losses and air resistance, find the height H the jet rises above the nozzle. Use g = 9.81 m/s².
A heat engine works between a hot reservoir at 500 °C and a cold reservoir at 35 °C. Find the highest possible thermal efficiency ηmax.
TH = 500 °CTL = 35 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A Carnot heat engine receives 110 kW of heat from a source at 750 °C and rejects heat to the surroundings at 30 °C. All of its work drives a Carnot refrigerator that removes heat from a freezer at -20 °C and also rejects heat to the surroundings at 30 °C. Find the rate Q̇L at which heat is removed from the freezer.
TH = 750 °CT0 = 30 °CTL = -20 °CQ̇H = 110 kW
Q̇L = kW
19.Waves, sound & opticsMedium
An object stands 60 cm in front of a thin converging lens with a focal length of 15 cm. Find the image distance di. Use the sign convention 1/f = 1/do + 1/di (f < 0 for a diverging lens, di < 0 for a virtual image).
do = 60 cmf = 15 cm
di = cm
20.Waves, sound & opticsHard
Light of wavelength 532 nm falls at right angles on a grating with 1200 lines per millimetre. Find the angle θ1 of the order-1 maximum.
N = 1200 mm⁻¹λ = 532 nmm = 1
θ1 = °
3Solutions
1.Kinematics
Answer: t = 3.125 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 90/3.6 = 25 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 25/8 = 3.125 s
Answer
t = 3.125 s
2.Kinematics
Answer: hmax = 34.13 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Rise above the roof
0 = v₀² − 2·g·Δh → Δh = 9²/(2·9.81) = 4.128 m
Height above the ground
hmax = 30 + 4.128 = 34.13 m
Answer
hmax = 34.13 m
3.Newton’s laws
Answer: μ = 0.148
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
a = v₀²/(2d) = 3²/(2·3.1) = 1.452 m/s²
Friction coefficient
μ·m·g = m·a → μ = a/g = 1.452/9.81 = 0.148
Answer
μ = 0.148
4.Newton’s laws
Answer: a = 6.744 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Solve the range formula for v₀
v₀ = √(g·R/sin 2θ) = √(9.81·20/sin 100°) = 14.11 m/s
Answer
v0 = 14.11 m/s
6.Projectile motion
Answer: t = 3.314 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 22·cos 15° = 21.25 m/s
vy = v0·sin θ = 22·sin 15° = 5.694 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 35 + 5.694·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (5.694 + √(32.42 + 686.7))/9.81 = 3.314 s
Answer
t = 3.314 s
7.Work & energy
Answer: P = 44.4 kW
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). Power is force times speed: P = F·v.
Driving force
m·g = 1200·9.81 = 11772 N
mg·sin θ = 11772·sin 5° = 1026 N
F = 1026 + 750 = 1776 N
Power
v = 90/3.6 = 25 m/s
P = F·v = 1776·25 = 44400 W = 44.4 kW
Answer
P = 44.4 kW
8.Work & energy
Answer: v = 9.185 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 9.81·(5 − 0.2·3.5) = 42.18 J
Speed at the spring
½mv² = mg(h − μL) → v = √(2g(h − μL)) = √(2·9.81·4.3) = 9.185 m/s
Answer
v = 9.185 m/s
9.Momentum & collisions
Answer: v′1 = −1.615 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (2.5 − 4)/(2.5 + 4)·7 = −1.615 m/s
v′2 = 2·2.5/(2.5 + 4)·7 = 5.385 m/s
Answer
v′1 = −1.615 m/s
The minus sign means the first glider bounces back.
10.Momentum & collisions
Answer: Favg = 280 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.2·(12 + 23) = 7 N·s
Average force
Favg = J/Δt = 7/0.025 = 280 N
Answer
Favg = 280 N
11.Hydrostatic force
Answer: F = 88.29 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 3/2 = 2 m
A = H·b = 3·1.5 = 4.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2·4.5 = 88.29 kN
Answer
F = 88.29 kN
12.Hydrostatic force
Answer: ycp = 2.375 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 3/2 = 2 m
A = H·b = 3·3 = 9 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2·9 = 176.6 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Ic = b·H³/12 = 3·3³/12 = 6.75 m⁴
ycp = yc + Ic/(yc·A) = 2 + 6.75/(2·9) = 2.375 m
Answer
ycp = 2.375 m
13.Continuity & Bernoulli
Answer: Q = 25.72 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity
v1 = v2·(60/100)² = 0.36·v2
Bernoulli between inlet and throat
The pipe is horizontal, so only pressure and velocity change.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Exit velocity
β = 20/75 = 0.2667
v2 = √(2p1/(ρ(1 − β⁴))) = √(2·70000/(1000·0.9949)) = 11.86 m/s
Height of the jet
Bernoulli along the jet: at the top the velocity is zero and the pressure is atmospheric again.
H = v2²/(2g) = 11.86²/(2·9.81) = 7.172 m
Answer
H = 7.172 m
15.Ideal gas law
Answer: V = 72.67 L
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = 370/16.04 = 23.07 mol
T = 30 + 273.15 = 303.1 K
Volume
V = nRT/P = 23.07·8.314·303.1/800 = 72.67 L
Answer
V = 72.67 L
16.Ideal gas law
Answer: ρ = 5.586 kg/m³
Ideal gas density: ρ = PM/(RT).
Rearrange the gas law
PV = (m/M)RT → ρ = m/V = PM/(RT)
T = 200 + 273.15 = 473.1 K
Density
ρ = 550·39.95/(8.314·473.1) = 5.586 kg/m³
Answer
ρ = 5.586 kg/m³
17.Heat engines & refrigerators
Answer: ηmax = 60.14 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 500 + 273.15 = 773.1 K
TL = 35 + 273.15 = 308.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 308.1/773.1 = 60.14 %
Answer
ηmax = 60.14 %
18.Heat engines & refrigerators
Answer: Q̇L = 391.9 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 750 + 273.15 = 1023 K
T0 = 30 + 273.15 = 303.1 K
TL = -20 + 273.15 = 253.1 K
Engine work
η = 1 − 303.1/1023 = 0.7037
Ẇ = 0.7037·110 = 77.41 kW
Heat removed by the refrigerator
COPR = 253.1/(303.1 − 253.1) = 5.063
Q̇L = 5.063·77.41 = 391.9 kW
Answer
Q̇L = 391.9 kW
19.Waves, sound & optics
Answer: di = 20 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/15 − 1/60
di = 20 cm
Ray diagram
real, on the far side of the lens
Answer
di = 20 cm
20.Waves, sound & optics
Answer: θ1 = 39.67 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …