Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane needs a speed of 220 km/h to take off and the usable runway is 2100 m long. Starting from rest, what constant acceleration a does it need?
v₀ = 0v = 220 km/hs = 2100 m
a = m/s²
2.KinematicsHard
A ball is thrown straight up at 12 m/s from the edge of a roof 30 m above the ground. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax above the ground.
v₀ = 12 m/sh₀ = 30 mg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A 9 kg block slides down a slope at 20° to the horizontal. The coefficient of kinetic friction is 0.25. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 9 kgθ = 20°μ = 0.25g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 35° with a speed of 11.5 m/s. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 11.5 m/sθ = 35°μ = 0.2g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is launched at 70° above horizontal from level ground. Ignore air resistance. Find the maximum height H the ball reaches.
v0 = 16 m/sθ = 70°g = 9.81 m/s²
H = m
6.Projectile motionHard
A ball is launched at 17 m/s and 40° above the horizontal from the top of a 10 m cliff. Ignore air resistance and use g = 9.81 m/s². At what angle α below the horizontal does it hit the ground?
v₀ = 17 m/sθ = 40°h = 10 mg = 9.81 m/s²
α = °
7.Work & energyMedium
A block slides from rest down a slope at 45° to the horizontal. The coefficient of kinetic friction is 0.35. Find its speed v after it has slid 19 m along the slope.
θ = 45°μ = 0.35d = 19 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 0.5 kg block is released from rest at height 4.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 1.5 m long (μ = 0.3) and then runs onto a spring (k = 2000 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
m = 0.5 kgh = 4.5 mL = 1.5 mμ = 0.3k = 2000 N/mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 12 g bullet is fired horizontally into a 2.5 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 21 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 12 gM = 2.5 kgh = 21 cmg = 9.81 m/s²
v = m/s
10.Momentum & collisionsHard
At a crossing a 1100 kg car travelling east at 21 m/s collides with a 900 kg car travelling north at 16 m/s. The cars lock together. Find the speed v′ of the wreck just after the collision.
m1 = 1100 kgv1 = 21 m/s (E)m2 = 900 kgv2 = 16 m/s (N)
v′ = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 4 mH = 2 mb = 3 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of seawater, with its top edge 0.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows through a horizontal pipe that narrows from 100 mm to 50 mm. In the wide section the pressure is 240 kPa and the velocity is 1.75 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 100 mm to 75 mm while rising 3 m. At section 1 the pressure is 380 kPa and the velocity is 2.25 m/s. Ignoring losses, find the pressure p2 at section 2.
A reversible refrigerator keeps a cold room at -10 °C by removing 8.5 kW of heat, and rejects heat to the surroundings at 40 °C. Find the rate Q̇H at which it rejects heat.
TL = -10 °CTH = 40 °CQ̇L = 8.5 kW
Q̇H = kW
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at -18 °C in a kitchen at 28 °C, removing heat from the cold space at 3 kW. Find the minimum power input Ẇmin.
TH = 28 °CTL = -18 °CQ̇L = 3 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
A source of 400 Hz moves at 25 m/s towards a stationary observer. The speed of sound is 343 m/s. Find the frequency f′ that the observer hears.
f = 400 Hzv = 343 m/svs = 25 m/s
f′ = Hz
20.Waves, sound & opticsHard
An object is 4 cm in front of a convex mirror with a radius of curvature of 40 cm. Find the image distance di, positive for an image in front of the mirror (real) and negative for one behind it (virtual).
do = 4 cmR = 40 cm
di = cm
3Solutions
1.Kinematics
Answer: a = 0.8892 m/s²
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v = 220/3.6 = 61.11 m/s
Acceleration
a = v²/(2s) = 61.11²/(2·2100) = 0.8892 m/s²
Answer
a = 0.8892 m/s²
2.Kinematics
Answer: hmax = 37.34 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Rise above the roof
0 = v₀² − 2·g·Δh → Δh = 12²/(2·9.81) = 7.339 m
Height above the ground
hmax = 30 + 7.339 = 37.34 m
Answer
hmax = 37.34 m
3.Newton’s laws
Answer: a = 1.051 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 35° + 0.2·cos 35°) = 7.234 m/s²
Distance
d = v₀²/(2a) = 11.5²/(2·7.234) = 9.141 m
Answer
d = 9.141 m
5.Projectile motion
Answer: H = 11.52 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 16·cos 70° = 5.472 m/s
vy = v0·sin θ = 16·sin 70° = 15.04 m/s
Highest point
At the top the vertical velocity is zero: vy² = 2gH.
H = vy²/(2g) = 15.04²/(2·9.81) = 11.52 m
Answer
H = 11.52 m
6.Projectile motion
Answer: α = 53.76 °
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 17·cos 40° = 13.02 m/s
vy0 = 17·sin 40° = 10.93 m/s
Vertical speed at impact
Energy or v² = v₀² + 2as in the vertical direction.
vy = √(10.93² + 2·9.81·10) = 17.77 m/s
Impact angle
tan α = vy/vx = 17.77/13.02 → α = 53.76°
Answer
α = 53.76°
7.Work & energy
Answer: v = 13.09 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·19·(0.7071 − 0.35·0.7071)) = 13.09 m/s
Answer
v = 13.09 m/s
8.Work & energy
Answer: v = 8.914 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 4.905·(4.5 − 0.3·1.5) = 19.87 J
Speed at the spring
½mv² = mg(h − μL) → v = √(2g(h − μL)) = √(2·9.81·4.05) = 8.914 m/s
Answer
v = 8.914 m/s
9.Momentum & collisions
Answer: v = 424.9 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Swing after impact
V = √(2·g·h) = √(2·9.81·0.21) = 2.03 m/s
Collision
m·v = (m + M)·V → v = (0.012 + 2.5)·2.03/0.012 = 424.9 m/s
Answer
v = 424.9 m/s
10.Momentum & collisions
Answer: v′ = 13.61 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 303.1 K, T2 = 503.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 10·(100/750)·(503.1/303.1) = 2.213 L
Answer
V2 = 2.213 L
17.Heat engines & refrigerators
Answer: Q̇H = 10.12 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 40 + 273.15 = 313.1 K
TL = -10 + 273.15 = 263.1 K
Reversible heat ratio
Q̇H = Q̇L·TH/TL = 8.5·313.1/263.1 = 10.12 kW
Answer
Q̇H = 10.12 kW
Power input: Ẇ = 1.615 kW.
18.Heat engines & refrigerators
Answer: Ẇmin = 0.5409 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇L/COP = 3/5.547 = 0.5409 kW
Answer
Ẇmin = 0.5409 kW
19.Waves, sound & optics
Answer: f′ = 431.4 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.