Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A driver moving at 36 km/h sees an obstacle. Her reaction time is 1.2 s, after which the car brakes with a constant deceleration of 8 m/s². Find the total stopping distance d from the moment she sees the obstacle.
v₀ = 36 km/htr = 1.2 sa = −8 m/s²
d = m
2.KinematicsHard
A ball is thrown straight up at 16 m/s from the edge of a roof 10 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 16 m/sh₀ = 10 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A box slides across a level floor with an initial speed of 5 m/s and comes to rest after 8.5 m. Use g = 9.81 m/s². Find the coefficient of kinetic friction μ.
v₀ = 5 m/sd = 8.5 mg = 9.81 m/s²
μ =
4.Newton’s lawsHard
A 6.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 5 kg mass. The coefficient of kinetic friction between block and table is 0.25. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 6.5 kgm2 = 5 kgμ = 0.25g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is kicked from level ground at 40 m/s and 35° above the horizontal towards a wall 61 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 40 m/sθ = 35°x = 61 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is launched at 50° above horizontal from the top of a 35 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 25 m/sθ = 50°h = 35 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A block slides from rest down a slope at 25° to the horizontal. The coefficient of kinetic friction is 0.1. Find its speed v after it has slid 9 m along the slope.
θ = 25°μ = 0.1d = 9 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A spring of stiffness 500 N/m at the bottom of a 30° slope is compressed by 15 cm against a 2 kg block and released. The coefficient of kinetic friction between block and slope is 0.15. How far d up the slope does the block travel from the release point before it stops? (Ignore the short distance over which the spring pushes, i.e. take friction and gravity over the whole distance d.)
A 1000 kg car moving at 5 m/s runs into a stationary 1000 kg car and the two lock together. How much kinetic energy ΔK is lost in the collision?
m1 = 1000 kgv1 = 5 m/sm2 = 1000 kgv2 = 0
ΔK = J
10.Momentum & collisionsHard
A 0.1 kg ball hits a wall at 25 m/s and bounces straight back at 19 m/s. The contact lasts 20 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.1 kgvin = 25 m/svout = 19 m/sΔt = 20 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 2 mH = 1 mb = 2 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
13.Continuity & BernoulliMedium
Water flows through a horizontal venturi meter with an inlet diameter of 80 mm and a throat diameter of 40 mm. The pressure at the inlet is 44 kPa higher than at the throat. Ignoring losses, find the flow rate Q.
A closed water tank has compressed air above the water at a gauge pressure of 180 kPa. Water leaves through an opening with a diameter of 40 mm, 3 m below the water surface, into the open air. Ignoring losses, find the flow rate Q. Use g = 9.81 m/s².
A heat engine works between a hot reservoir at 625 °C and a cold reservoir at 15 °C. It takes in 4000 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 625 °CTL = 15 °CQH = 4000 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A heat engine takes in 4800 kJ of heat from a reservoir at 400 °C, produces 1632 kJ of work and rejects the rest to a reservoir at 15 °C, per cycle. Find the total entropy generated Sgen per cycle.
TH = 400 °CTL = 15 °CQH = 4800 kJW = 1632 kJ
Sgen = kJ/K
19.Waves, sound & opticsMedium
A source of 300 Hz moving at 15 m/s and an observer moving at 15 m/s move away from each other. The speed of sound is 343 m/s. Find the frequency f′ that the observer hears.
f = 300 Hzv = 343 m/svs = 15 m/svo = 15 m/s
f′ = Hz
20.Waves, sound & opticsHard
Light of wavelength 532 nm falls at right angles on a grating with 200 lines per millimetre. Find the angle θ2 of the order-2 maximum.
N = 200 mm⁻¹λ = 532 nmm = 2
θ2 = °
3Solutions
1.Kinematics
Answer: d = 18.25 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 36/3.6 = 10 m/s
Reaction distance
d1 = v₀·tr = 10·1.2 = 12 m
Braking distance
d2 = v₀²/(2a) = 10²/(2·8) = 6.25 m
Total
d = 12 + 6.25 = 18.25 m
Answer
d = 18.25 m
2.Kinematics
Answer: t = 3.799 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−10 = 16·t − ½·9.81·t²
4.905·t² − 16·t − 10 = 0
Solve the quadratic
Only the positive root is physical.
t = (16 + √(16² + 2·9.81·10))/9.81 = 3.799 s
Answer
t = 3.799 s
3.Newton’s laws
Answer: μ = 0.1499
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
a = v₀²/(2d) = 5²/(2·8.5) = 1.471 m/s²
Friction coefficient
μ·m·g = m·a → μ = a/g = 1.471/9.81 = 0.1499
Answer
μ = 0.1499
4.Newton’s laws
Answer: T = 34.65 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 40·cos 35° = 32.77 m/s
t = x/vx = 61/32.77 = 1.862 s
Height at that time
y = 22.94·1.862 − ½·9.81·1.862² = 25.71 m
Answer
y = 25.71 m
The ball is still rising at the wall.
6.Projectile motion
Answer: t = 5.261 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 25·cos 50° = 16.07 m/s
vy = v0·sin θ = 25·sin 50° = 19.15 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 35 + 19.15·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (19.15 + √(366.8 + 686.7))/9.81 = 5.261 s
Answer
t = 5.261 s
7.Work & energy
Answer: v = 7.657 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·9·(0.4226 − 0.1·0.9063)) = 7.657 m/s
Answer
v = 7.657 m/s
8.Work & energy
Answer: d = 0.4551 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 15 cm = 0.15 m
½kx² = ½·500·0.15² = 5.625 J
Energy balance along the slope
m·g = 2·9.81 = 19.62 N
½kx² = mg·d·(sin θ + μ·cos θ)
d = 5.625/(19.62·(0.5 + 0.15·0.866)) = 0.4551 m
Answer
d = 0.4551 m
9.Momentum & collisions
Answer: ΔK = 6250 J
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 1000·5/2000 = 2.5 m/s
Kinetic energy before and after
Kbefore = ½·1000·5² = 12500 J
Kafter = ½·2000·2.5² = 6250 J
Energy lost
ΔK = 12500 − 6250 = 6250 J
Answer
ΔK = 6250 J
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: J = 4.4 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.1·(19 + 25) = 4.4 N·s
Answer
J = 4.4 N·s
11.Hydrostatic force
Answer: F = 128.8 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 2.5/2 = 1.75 m
A = H·b = 2.5·3 = 7.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·1.75·7.5 = 128.8 kN
Answer
F = 128.8 kN
12.Hydrostatic force
Answer: F = 49.05 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 1/2 = 2.5 m
A = H·b = 1·2 = 2 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.5·2 = 49.05 kN
Answer
F = 49.05 kN
13.Continuity & Bernoulli
Answer: Q = 12.17 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity
v1 = v2·(40/80)² = 0.25·v2
Bernoulli between inlet and throat
The pipe is horizontal, so only pressure and velocity change.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 625 + 273.15 = 898.1 K
TL = 15 + 273.15 = 288.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 288.1/898.1 = 67.92 %
Maximum work
Wmax = ηmax·QH = 0.6792·4000 = 2717 kJ
Answer
Wmax = 2717 kJ
18.Heat engines & refrigerators
Answer: Sgen = 3.864 kJ/K
Entropy generation: over a full cycle the working fluid has no net entropy change. The hot reservoir loses QH/TH and the cold reservoir gains QL/TL. Their sum is the entropy generated, which is zero for a reversible cycle and positive for every real one.
Heat rejected
QL = QH − W = 4800 − 1632 = 3168 kJ
Absolute temperatures
TH = 400 + 273.15 = 673.1 K
TL = 15 + 273.15 = 288.1 K
Entropy changes of the reservoirs
ΔSH = −4800/673.1 = −7.131 kJ/K
ΔSL = 3168/288.1 = 10.99 kJ/K
Sgen = 10.99 − 7.131 = 3.864 kJ/K
Answer
Sgen = 3.864 kJ/K
Sgen > 0, so the engine is possible but irreversible.
19.Waves, sound & optics
Answer: f′ = 274.9 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …