Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 100 km/h brakes with a constant deceleration of 4.5 m/s² until it stops. Find the braking distance s.
v₀ = 100 km/ha = −4.5 m/s²v = 0
s = m
2.KinematicsHard
Ball A is dropped from rest from a height of 25 m. At the same instant ball B is thrown straight up from the ground directly below at 14 m/s. Ignore air resistance and use g = 9.81 m/s². When do the balls meet? Find t.
H = 25 mv0B = 14 m/sg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
An 8 kg block slides down a slope at 30° to the horizontal. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 8 kgθ = 30°μ = 0.15g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 30° with a speed of 7 m/s. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 7 m/sθ = 30°μ = 0.15g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is kicked from level ground at 14 m/s and 40° above the horizontal towards a wall 12 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 14 m/sθ = 40°x = 12 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is launched at 26 m/s and 35° above the horizontal from the top of a 30 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the greatest height H above the ground at the foot of the cliff.
v₀ = 26 m/sθ = 35°h = 30 mg = 9.81 m/s²
H = m
7.Work & energyMedium
A 5 kg block slides 16 m down a slope at 15° to the horizontal, with a coefficient of kinetic friction of 0.15. Find the work Wf done against friction.
m = 5 kgθ = 15°μ = 0.15d = 16 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 2.5 kg block is released from rest at height 4 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 2 m long (μ = 0.1) and then runs onto a spring (k = 1000 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 2.5 kgh = 4 mL = 2 mμ = 0.1k = 1000 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 4.5 kg glider moving at 11 m/s makes a perfectly elastic head-on collision with a 2.5 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 4.5 kgm2 = 2.5 kgv1 = 11 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
A 0.5 kg ball hits a wall at 26 m/s and bounces straight back at 12 m/s. The contact lasts 50 ms. Find the average force Favg of the wall on the ball.
m = 0.5 kgvin = 26 m/svout = 12 m/sΔt = 50 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of glycerin, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal pipe that narrows from 100 mm to 40 mm. In the wide section the pressure is 100 kPa and the velocity is 2 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 100 mm to 50 mm while rising 1 m. At section 1 the pressure is 120 kPa and the velocity is 2.75 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine receives heat from a source at 300 °C and rejects heat to the surroundings at 25 °C. Its actual thermal efficiency is 24%. Find its second-law efficiency ηII, the ratio of the actual efficiency to the Carnot efficiency.
TH = 300 °CTL = 25 °Cη = 24%
ηII = %
18.Heat engines & refrigeratorsHard
Two Carnot engines work in series. Engine A receives heat from a reservoir at 800 °C and rejects heat to an intermediate reservoir at temperature Tm. Engine B takes all that heat and rejects heat to a reservoir at 15 °C. Both engines have the same thermal efficiency. Find Tm in °C.
TH = 800 °CTL = 15 °C
Tm = °C
19.Waves, sound & opticsMedium
A string fixed at both ends is 1 m long; waves travel on it at 240 m/s. Find the frequency f5 of its harmonic number 5.
v = 240 m/sn = 5L = 1 m
f5 = Hz
20.Waves, sound & opticsHard
An object is 4 cm in front of a convex mirror with a radius of curvature of 60 cm. Find the image distance di, positive for an image in front of the mirror (real) and negative for one behind it (virtual).
do = 4 cmR = 60 cm
di = cm
3Solutions
1.Kinematics
Answer: s = 85.73 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 100/3.6 = 27.78 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 27.78²/(2·4.5) = 85.73 m
Answer
s = 85.73 m
2.Kinematics
Answer: t = 1.786 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Meeting time
Up is positive, the ground is y = 0.
25 − ½g·t² = 14·t − ½g·t² → t = 25/14 = 1.786 s
Answer
t = 1.786 s
3.Newton’s laws
Answer: a = 3.631 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 30° + 0.15·cos 30°) = 6.179 m/s²
Distance
d = v₀²/(2a) = 7²/(2·6.179) = 3.965 m
Answer
d = 3.965 m
5.Projectile motion
Answer: y = 3.928 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 14·cos 40° = 10.72 m/s
t = x/vx = 12/10.72 = 1.119 s
Height at that time
y = 8.999·1.119 − ½·9.81·1.119² = 3.928 m
Answer
y = 3.928 m
The ball is already on its way down at the wall.
6.Projectile motion
Answer: H = 41.34 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Vertical launch speed
vy = 26·sin 35° = 14.91 m/s
Rise above the cliff
Δh = vy²/(2g) = 14.91²/(2·9.81) = 11.34 m
Height above the ground
H = 30 + 11.34 = 41.34 m
Answer
H = 41.34 m
7.Work & energy
Answer: Wf = 113.7 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 49.05·0.9659 = 47.38 N
F = μN = 0.15·47.38 = 7.107 N
Work against friction
Wf = F·d = 7.107·16 = 113.7 J
Answer
Wf = 113.7 J
8.Work & energy
Answer: x = 43.17 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 24.53·(4 − 0.1·2) = 93.2 J
Maximum compression
½kx² = 93.2 → x = √(2·93.2/1000) = 0.4317 m = 43.17 cm
Answer
x = 43.17 cm
9.Momentum & collisions
Answer: v′1 = 3.143 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (4.5 − 2.5)/(4.5 + 2.5)·11 = 3.143 m/s
v′2 = 2·4.5/(4.5 + 2.5)·11 = 14.14 m/s
Answer
v′1 = 3.143 m/s
10.Momentum & collisions
Answer: Favg = 380 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.5·(12 + 26) = 19 N·s
Average force
Favg = J/Δt = 19/0.05 = 380 N
Answer
Favg = 380 N
11.Hydrostatic force
Answer: F = 128.8 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 2.5/2 = 5.25 m
A = H·b = 2.5·1 = 2.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·5.25·2.5 = 128.8 kN
Answer
F = 128.8 kN
12.Hydrostatic force
Answer: F = 243.3 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 2.5/2 = 5.25 m
A = H·b = 2.5·1.5 = 3.75 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·5.25·3.75 = 243.3 kN
Answer
F = 243.3 kN
13.Continuity & Bernoulli
Answer: p2 = 23.88 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 300 + 273.15 = 573.1 K
TL = 25 + 273.15 = 298.1 K
Carnot efficiency
ηCarnot = 1 − 298.1/573.1 = 47.98 %
Second-law efficiency
ηII = η/ηCarnot = 24/47.98 = 50.02 %
Answer
ηII = 50.02 %
18.Heat engines & refrigerators
Answer: Tm = 282.9 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 800 + 273.15 = 1073 K
TL = 15 + 273.15 = 288.1 K
Equal efficiencies
1 − Tm/TH = 1 − TL/Tm gives Tm² = TH·TL.
Tm = √(1073·288.1) = 556.1 K = 282.9 °C
Answer
Tm = 282.9 °C
19.Waves, sound & optics
Answer: f5 = 600 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 2L/n = 2·1/5 = 0.4 m
Frequency
f = v/λ = 240/0.4 = 600 Hz
Answer
f5 = 600 Hz
20.Waves, sound & optics
Answer: di = −3.529 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.