Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 108 km/h brakes with a constant deceleration of 4.5 m/s² until it stops. Find the braking distance s.
v₀ = 108 km/ha = −4.5 m/s²v = 0
s = m
2.KinematicsHard
Ball A is dropped from rest from a height of 30 m. At the same instant ball B is thrown straight up from the ground directly below at 29 m/s. Ignore air resistance and use g = 9.81 m/s². When do the balls meet? Find t.
H = 30 mv0B = 29 m/sg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 6 kg block slides down a slope at 45° to the horizontal. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 6 kgθ = 45°μ = 0.15g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 3.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 2 kg mass. The table is frictionless. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 3.5 kgm2 = 2 kgμ = 0g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is kicked from level ground at 12 m/s and 55° above the horizontal towards a wall 11 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 12 m/sθ = 55°x = 11 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is launched at 20° above horizontal from the top of a 5 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 18 m/sθ = 20°h = 5 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A 5 kg block slides 6 m down a slope at 40° to the horizontal, with a coefficient of kinetic friction of 0.3. Find the work Wf done against friction.
m = 5 kgθ = 40°μ = 0.3d = 6 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 5 kg block is released from rest at height 2 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 1 m long (μ = 0.1) and then runs onto a spring (k = 2500 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 5 kgh = 2 mL = 1 mμ = 0.1k = 2500 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 1 kg glider moving at 11 m/s makes a perfectly elastic head-on collision with a 5 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 1 kgm2 = 5 kgv1 = 11 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
A 15 g bullet is fired horizontally into a 3 kg block hanging from light strings 0.9 m long, and stays in it. The strings swing out to a largest angle of 15° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 15 gM = 3 kgL = 0.9 mθ = 15°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of oil, with its top edge 3 m below the surface. Find the resultant hydrostatic force F on the gate.
A pitot-static tube in a water pipe reads a difference of 26 kPa between the stagnation pressure and the static pressure. Find the water velocity v at the tip.
p0 − p = 26 kPaρ = 1000 kg/m³
v = m/s
14.Continuity & BernoulliHard
Water flows up through a pipe that narrows from 150 mm to 40 mm while rising 10 m. At section 1 the pressure is 200 kPa and the velocity is 0.5 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 625 °C and a cold reservoir at 10 °C. It takes in 1700 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 625 °CTL = 10 °CQH = 1700 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 20 °C while it is 0 °C outside, delivering 13 kW of heat to the house. Find the minimum power input Ẇmin.
TH = 20 °CTL = 0 °CQ̇H = 13 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
An object stands 20 cm in front of a thin converging lens with a focal length of 8 cm. Find the image distance di. Use the sign convention 1/f = 1/do + 1/di (f < 0 for a diverging lens, di < 0 for a virtual image).
do = 20 cmf = 8 cm
di = cm
20.Waves, sound & opticsHard
An object is 50 cm in front of a convex mirror with a radius of curvature of 50 cm. Find the image distance di, positive for an image in front of the mirror (real) and negative for one behind it (virtual).
do = 50 cmR = 50 cm
di = cm
3Solutions
1.Kinematics
Answer: s = 100 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 108/3.6 = 30 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 30²/(2·4.5) = 100 m
Answer
s = 100 m
2.Kinematics
Answer: t = 1.034 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Meeting time
Up is positive, the ground is y = 0.
30 − ½g·t² = 29·t − ½g·t² → t = 30/29 = 1.034 s
Answer
t = 1.034 s
3.Newton’s laws
Answer: a = 5.896 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 12·cos 55° = 6.883 m/s
t = x/vx = 11/6.883 = 1.598 s
Height at that time
y = 9.83·1.598 − ½·9.81·1.598² = 3.182 m
Answer
y = 3.182 m
The ball is already on its way down at the wall.
6.Projectile motion
Answer: t = 1.816 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 18·cos 20° = 16.91 m/s
vy = v0·sin θ = 18·sin 20° = 6.156 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 5 + 6.156·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (6.156 + √(37.9 + 98.1))/9.81 = 1.816 s
Answer
t = 1.816 s
7.Work & energy
Answer: Wf = 67.63 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 49.05·0.766 = 37.57 N
F = μN = 0.3·37.57 = 11.27 N
Work against friction
Wf = F·d = 11.27·6 = 67.63 J
Answer
Wf = 67.63 J
8.Work & energy
Answer: x = 27.3 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 49.05·(2 − 0.1·1) = 93.2 J
Maximum compression
½kx² = 93.2 → x = √(2·93.2/2500) = 0.273 m = 27.3 cm
Answer
x = 27.3 cm
9.Momentum & collisions
Answer: v′1 = −7.333 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (1 − 5)/(1 + 5)·11 = −7.333 m/s
v′2 = 2·1/(1 + 5)·11 = 3.667 m/s
Answer
v′1 = −7.333 m/s
The minus sign means the first glider bounces back.
10.Momentum & collisions
Answer: v = 155.9 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 0.9·(1 − cos 15°) = 0.03067 m
Speed after impact
V = √(2·9.81·0.03067) = 0.7757 m/s
Collision
v = (m + M)·V/m = 3.015·0.7757/0.015 = 155.9 m/s
Answer
v = 155.9 m/s
11.Hydrostatic force
Answer: F = 60.7 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 1.5/2 = 2.75 m
A = H·b = 1.5·1.5 = 2.25 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.75·2.25 = 60.7 kN
Answer
F = 60.7 kN
12.Hydrostatic force
Answer: F = 137.6 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 2.5/2 = 4.25 m
A = H·b = 2.5·1.5 = 3.75 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·4.25·3.75 = 137.6 kN
Answer
F = 137.6 kN
13.Continuity & Bernoulli
Answer: v = 7.211 m/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Bernoulli to the stagnation point
The flow comes to rest at the tip, so its kinetic energy shows up as extra pressure.
p0 − p = ½ρv²
v = √(2·26000/1000) = 7.211 m/s
Answer
v = 7.211 m/s
14.Continuity & Bernoulli
Answer: p2 = 77.31 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 625 + 273.15 = 898.1 K
TL = 10 + 273.15 = 283.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 283.1/898.1 = 68.47 %
Maximum work
Wmax = ηmax·QH = 0.6847·1700 = 1164 kJ
Answer
Wmax = 1164 kJ
18.Heat engines & refrigerators
Answer: Ẇmin = 0.8869 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇H/COP = 13/14.66 = 0.8869 kW
Answer
Ẇmin = 0.8869 kW
19.Waves, sound & optics
Answer: di = 13.33 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/8 − 1/20
di = 13.33 cm
Ray diagram
real, on the far side of the lens
Answer
di = 13.33 cm
20.Waves, sound & optics
Answer: di = −16.67 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.