Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane starts from rest and accelerates uniformly at 3.25 m/s² along a runway. Find its speed v after 1200 m.
v₀ = 0a = 3.25 m/s²s = 1200 m
v = m/s
2.KinematicsHard
A model rocket is launched straight up from rest. Its engine gives it a constant upward acceleration of 26 m/s² for 1 s, after which the engine stops and the rocket moves freely. Ignore air resistance and use g = 9.81 m/s². How long after launch does it hit the ground? Find t.
a = 26 m/s²t1 = 1 sg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 2 kg block slides down a frictionless slope at 40° to the horizontal. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 2 kgθ = 40°μ = 0g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
Two blocks on a level floor are joined by a light horizontal string. A horizontal force of 90 N pulls the front 1 kg block; the 11 kg block is towed behind. The coefficient of kinetic friction is 0.25 for both blocks. Use g = 9.81 m/s². Find the acceleration a of the blocks.
m1 = 11 kgm2 = 1 kgF = 90 Nμ = 0.25g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched from level ground at 28 m/s and must land 75 m away. Ignore air resistance and use g = 9.81 m/s². Find the smaller of the two possible launch angles θ.
v₀ = 28 m/sR = 75 mg = 9.81 m/s²
θ = °
6.Projectile motionHard
A ball is thrown from ground level at 38 m/s and 30° above the horizontal. It lands on the flat roof of a building 8 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 38 m/sθ = 30°hroof = 8 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A block slides from rest down a slope at 40° to the horizontal. The coefficient of kinetic friction is 0.4. Find its speed v after it has slid 7 m along the slope.
θ = 40°μ = 0.4d = 7 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 3 kg block rests on a rough horizontal table (μ = 0.2). A light string runs from it over a smooth pulley at the edge of the table to a hanging 6 kg block. The system is released from rest. Find the speed v of the blocks after the hanging block has dropped 1.5 m.
m1 = 3 kgm2 = 6 kgμ = 0.2d = 1.5 mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 2.5 kg glider moving at 10 m/s makes a perfectly elastic head-on collision with a 2 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 2.5 kgm2 = 2 kgv1 = 10 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 0.1 kg ball hits a wall at 20 m/s and bounces straight back at 16 m/s. The contact lasts 50 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.1 kgvin = 20 m/svout = 16 m/sΔt = 50 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 2 mH = 2 mb = 2 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 3 m wide sits in the wall of a tank of oil, with its top edge 3 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 3 mH = 3 mb = 3 mρ = 880 kg/m³g = 9.81 m/s²
F = kN
13.Continuity & BernoulliMedium
Water flows through a horizontal pipe that narrows from 75 mm to 50 mm. In the wide section the pressure is 130 kPa and the velocity is 0.5 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 100 mm to 50 mm while rising 5 m. At section 1 the pressure is 330 kPa and the velocity is 0.75 m/s. Ignoring losses, find the pressure p2 at section 2.
A reversible refrigerator keeps a cold room at 5 °C by removing 4.5 kW of heat, and rejects heat to the surroundings at 20 °C. Find the rate Q̇H at which it rejects heat.
TL = 5 °CTH = 20 °CQ̇L = 4.5 kW
Q̇H = kW
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 20 °C while it is 2 °C outside, delivering 8 kW of heat to the house. Find the highest possible coefficient of performance COPmax.
TH = 20 °CTL = 2 °CQ̇H = 8 kW
COPmax =
19.Waves, sound & opticsMedium
An object stands 10 cm in front of a thin converging lens with a focal length of 30 cm. Find the magnification m (negative for an inverted image).
do = 10 cmf = 30 cm
m =
20.Waves, sound & opticsHard
Light of wavelength 405 nm falls at right angles on a grating with 200 lines per millimetre. Find the angle θ3 of the order-3 maximum.
N = 200 mm⁻¹λ = 405 nmm = 3
θ3 = °
3Solutions
1.Kinematics
Answer: v = 88.32 m/s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Speed after the distance
v = √(2·a·s) = √(2·3.25·1200) = 88.32 m/s
Answer
v = 88.32 m/s
(317.9 km/h)
2.Kinematics
Answer: t = 6.761 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Powered phase
v₁ = 26·1 = 26 m/s
h₁ = ½·26·1² = 13 m
Free flight to the ground
Solve −h₁ = v₁·t₂ − ½·g·t₂² for the positive root.
t₂ = (26 + √(26² + 2·9.81·13))/9.81 = 5.761 s
t = 1 + 5.761 = 6.761 s
Answer
t = 6.761 s
3.Newton’s laws
Answer: a = 6.306 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Range formula
R = v₀²·sin 2θ/g → sin 2θ = 9.81·75/28² = 0.9385
Angle
2θ = 69.79° → θ = 34.9°
Answer
θ = 34.9°
The other solution is 90° − θ = 55.1°.
6.Projectile motion
Answer: x = 111.7 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 32.91 m/s, vy = 19 m/s
Time to land on the roof
Larger root: the ball is descending.
8 = 19·t − 4.905·t²
t = (19 + √(19² − 2·9.81·8))/9.81 = 3.393 s
Horizontal distance
x = vx·t = 32.91·3.393 = 111.7 m
Answer
x = 111.7 m
7.Work & energy
Answer: v = 6.797 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·7·(0.6428 − 0.4·0.766)) = 6.797 m/s
Answer
v = 6.797 m/s
8.Work & energy
Answer: v = 4.202 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy released and lost
m₂g·d = 58.86·1.5 = 88.29 J
μ·m₁g·d = 0.2·29.43·1.5 = 8.829 J
Kinetic energy of both blocks
½(m₁ + m₂)v² = 79.46 → v = √(2·79.46/9) = 4.202 m/s
Answer
v = 4.202 m/s
9.Momentum & collisions
Answer: v′2 = 11.11 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (2.5 − 2)/(2.5 + 2)·10 = 1.111 m/s
v′2 = 2·2.5/(2.5 + 2)·10 = 11.11 m/s
Answer
v′2 = 11.11 m/s
10.Momentum & collisions
Answer: J = 3.6 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.1·(16 + 20) = 3.6 N·s
Answer
J = 3.6 N·s
11.Hydrostatic force
Answer: F = 117.7 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 2/2 = 3 m
A = H·b = 2·2 = 4 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3·4 = 117.7 kN
Answer
F = 117.7 kN
12.Hydrostatic force
Answer: F = 349.6 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 3/2 = 4.5 m
A = H·b = 3·3 = 9 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·4.5·9 = 349.6 kN
Answer
F = 349.6 kN
13.Continuity & Bernoulli
Answer: p2 = 129.5 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 20 + 273.15 = 293.1 K
TL = 5 + 273.15 = 278.1 K
Reversible heat ratio
Q̇H = Q̇L·TH/TL = 4.5·293.1/278.1 = 4.743 kW
Answer
Q̇H = 4.743 kW
Power input: Ẇ = 0.2427 kW.
18.Heat engines & refrigerators
Answer: COPmax = 16.29
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/30 − 1/10
di = −15 cm
Magnification
m = −di/do = −(−15)/10 = 1.5
Answer
m = 1.5
20.Waves, sound & optics
Answer: θ3 = 14.06 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …