Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 45 km/h brakes with a constant deceleration of 3.5 m/s² until it stops. How long does braking take? Find t.
v₀ = 45 km/ha = −3.5 m/s²v = 0
t = s
2.KinematicsHard
A ball is thrown straight up at 6 m/s from the edge of a roof 35 m above the ground. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax above the ground.
v₀ = 6 m/sh₀ = 35 mg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
Masses of 4 kg and 1 kg hang on either side of a light, frictionless pulley, connected by a light string. The system is released from rest. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 4 kgm2 = 1 kgg = 9.81 m/s²
T = N
4.Newton’s lawsHard
A 5.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 3.5 kg mass. The coefficient of kinetic friction between block and table is 0.2. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 5.5 kgm2 = 3.5 kgμ = 0.2g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is kicked from level ground at 32 m/s and 35° above the horizontal towards a wall 20 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 32 m/sθ = 35°x = 20 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is launched at 45° above horizontal from the top of a 35 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 19 m/sθ = 45°h = 35 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A 1 kg block slides 18 m down a slope at 35° to the horizontal, with a coefficient of kinetic friction of 0.2. Find the work Wf done against friction.
m = 1 kgθ = 35°μ = 0.2d = 18 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 2.5 kg block is released from rest at height 3.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 1 m long (μ = 0.1) and then runs onto a spring (k = 2500 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 2.5 kgh = 3.5 mL = 1 mμ = 0.1k = 2500 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 1900 kg car moving at 23 m/s runs into a stationary 1200 kg car and the two lock together. How much kinetic energy ΔK is lost in the collision?
m1 = 1900 kgv1 = 23 m/sm2 = 1200 kgv2 = 0
ΔK = J
10.Momentum & collisionsHard
At a crossing a 1100 kg car travelling east at 22 m/s collides with a 1500 kg car travelling north at 8 m/s. The cars lock together. Find the direction θ of the wreck just after the collision, measured north of east.
m1 = 1100 kgv1 = 22 m/s (E)m2 = 1500 kgv2 = 8 m/s (N)
θ = °
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
Water drains from a large open tank through a sharp-edged orifice with a diameter of 30 mm. The water level is kept 2.5 m above the orifice and the discharge coefficient is 0.61. Find the flow rate Q. Use g = 9.81 m/s².
d = 30 mmh = 2.5 mCd = 0.61g = 9.81 m/s²
Q = L/s
14.Continuity & BernoulliHard
A horizontal venturi meter (inlet 200 mm, throat 150 mm) carries water. A mercury U-tube manometer connected between the inlet and the throat shows a level difference of 50 mm. The discharge coefficient is 0.98. Find the flow rate Q. Use ρ = 1000 kg/m³ for water, 13 600 kg/m³ for mercury and g = 9.81 m/s².
A heat engine works between a hot reservoir at 775 °C and a cold reservoir at 15 °C. Find the highest possible thermal efficiency ηmax.
TH = 775 °CTL = 15 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at 4 °C in a kitchen at 28 °C, removing heat from the cold space at 4 kW. Find the highest possible coefficient of performance COPmax.
TH = 28 °CTL = 4 °CQ̇L = 4 kW
COPmax =
19.Waves, sound & opticsMedium
A pipe open at both ends is 0.5 m long. The speed of sound is 343 m/s. Find the frequency f4 of its harmonic number 4.
v = 343 m/sn = 4L = 0.5 m
f4 = Hz
20.Waves, sound & opticsHard
Light of wavelength 633 nm falls on two slits 0.3 mm apart. The screen is 2.5 m away. Find the distance y2 from the central bright fringe to bright fringe number 2.
λ = 633 nmd = 0.3 mmL = 2.5 mm = 2
y2 = mm
3Solutions
1.Kinematics
Answer: t = 3.571 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 45/3.6 = 12.5 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 12.5/3.5 = 3.571 s
Answer
t = 3.571 s
2.Kinematics
Answer: hmax = 36.83 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Rise above the roof
0 = v₀² − 2·g·Δh → Δh = 6²/(2·9.81) = 1.835 m
Height above the ground
hmax = 35 + 1.835 = 36.83 m
Answer
hmax = 36.83 m
3.Newton’s laws
Answer: T = 15.7 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Acceleration
The net driving force is the difference of the weights; it moves the total mass.
a = (4 − 1)·9.81/(4 + 1) = 5.886 m/s²
Tension from the lighter mass
T − m2·g = m2·a → T = 1·(9.81 + 5.886) = 15.7 N
Answer
T = 15.7 N
4.Newton’s laws
Answer: T = 25.18 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 32·cos 35° = 26.21 m/s
t = x/vx = 20/26.21 = 0.763 s
Height at that time
y = 18.35·0.763 − ½·9.81·0.763² = 11.15 m
Answer
y = 11.15 m
The ball is still rising at the wall.
6.Projectile motion
Answer: x = 58.73 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 19·cos 45° = 13.44 m/s
vy = v0·sin θ = 19·sin 45° = 13.44 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 35 + 13.44·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (13.44 + √(180.5 + 686.7))/9.81 = 4.371 s
Horizontal distance
x = vx·t = 13.44·4.371 = 58.73 m
Answer
x = 58.73 m
7.Work & energy
Answer: Wf = 28.93 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 9.81·0.8192 = 8.036 N
F = μN = 0.2·8.036 = 1.607 N
Work against friction
Wf = F·d = 1.607·18 = 28.93 J
Answer
Wf = 28.93 J
8.Work & energy
Answer: x = 25.83 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 24.53·(3.5 − 0.1·1) = 83.39 J
Maximum compression
½kx² = 83.39 → x = √(2·83.39/2500) = 0.2583 m = 25.83 cm
Answer
x = 25.83 cm
9.Momentum & collisions
Answer: ΔK = 194535 J
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 1900·23/3100 = 14.1 m/s
Kinetic energy before and after
Kbefore = ½·1900·23² = 502550 J
Kafter = ½·3100·14.1² = 308015 J
Energy lost
ΔK = 502550 − 308015 = 194535 J
Answer
ΔK = 194535 J
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: θ = 26.38 °
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Momentum components
px = 1100·22 = 24200 kg·m/s
py = 1500·8 = 12000 kg·m/s
Direction
tan θ = py/px = 0.4959 → θ = 26.38°
Answer
θ = 26.38°
11.Hydrostatic force
Answer: F = 154.5 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 3/2 = 3.5 m
A = H·b = 3·1.5 = 4.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.5·4.5 = 154.5 kN
Answer
F = 154.5 kN
12.Hydrostatic force
Answer: F = 88.29 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 2/2 = 1.5 m
A = H·b = 2·3 = 6 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·1.5·6 = 88.29 kN
Answer
F = 88.29 kN
13.Continuity & Bernoulli
Answer: Q = 3.02 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Ideal jet velocity
√(2gh) = √(2·9.81·2.5) = 7.004 m/s
Actual flow rate
The discharge coefficient accounts for the contraction of the jet and friction at the edge.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Pressure difference from the manometer
Δp = (13600 − 1000)·9.81·0.05 = 6180 Pa
Throat velocity
Continuity and Bernoulli together give the ideal throat velocity.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 775 + 273.15 = 1048 K
TL = 15 + 273.15 = 288.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 288.1/1048 = 72.51 %
Answer
ηmax = 72.51 %
18.Heat engines & refrigerators
Answer: COPmax = 11.55
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 2L/n = 2·0.5/4 = 0.25 m
Frequency
f = v/λ = 343/0.25 = 1372 Hz
Answer
f4 = 1372 Hz
20.Waves, sound & optics
Answer: y2 = 10.55 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …