Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 100 km/h brakes with a constant deceleration of 3.5 m/s² until it stops. How long does braking take? Find t.
v₀ = 100 km/ha = −3.5 m/s²v = 0
t = s
2.KinematicsHard
A ball is thrown straight up at 13 m/s from the edge of a roof 10 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 13 m/sh₀ = 10 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A box slides across a level floor with an initial speed of 7.5 m/s and comes to rest after 19 m. Use g = 9.81 m/s². Find the coefficient of kinetic friction μ.
v₀ = 7.5 m/sd = 19 mg = 9.81 m/s²
μ =
4.Newton’s lawsHard
A 1.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 4 kg mass. The coefficient of kinetic friction between block and table is 0.3. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 1.5 kgm2 = 4 kgμ = 0.3g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 25° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 20 m/sθ = 25°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is launched at 25° above horizontal from the top of a 10 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 33 m/sθ = 25°h = 10 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A car travelling at 90 km/h on a level road brakes hard and skids to a stop with its wheels locked. The coefficient of kinetic friction between the tyres and the road is 0.8. Find the stopping distance d.
v = 90 km/hμ = 0.8g = 9.81 m/s²
d = m
8.Work & energyHard
A 3 kg block rests on a rough horizontal table (μ = 0.4). A light string runs from it over a smooth pulley at the edge of the table to a hanging 4 kg block. The system is released from rest. Find the speed v of the blocks after the hanging block has dropped 3 m.
m1 = 3 kgm2 = 4 kgμ = 0.4d = 3 mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 1600 kg car moving at 18 m/s runs into a stationary 1400 kg car and the two lock together. How much kinetic energy ΔK is lost in the collision?
m1 = 1600 kgv1 = 18 m/sm2 = 1400 kgv2 = 0
ΔK = J
10.Momentum & collisionsHard
At a crossing a 1200 kg car travelling east at 10 m/s collides with a 900 kg car travelling north at 15 m/s. The cars lock together. Find the direction θ of the wreck just after the collision, measured north of east.
m1 = 1200 kgv1 = 10 m/s (E)m2 = 900 kgv2 = 15 m/s (N)
θ = °
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of oil, with its top edge 4 m below the surface. Find the depth ycp of the centre of pressure below the surface.
d = 4 mH = 3 mb = 2 mρ = 880 kg/m³g = 9.81 m/s²
ycp = m
13.Continuity & BernoulliMedium
Water flows through a horizontal pipe that narrows from 100 mm to 40 mm. In the wide section the pressure is 230 kPa and the velocity is 1.75 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A horizontal venturi meter (inlet 150 mm, throat 75 mm) carries water. A mercury U-tube manometer connected between the inlet and the throat shows a level difference of 310 mm. The discharge coefficient is 0.96. Find the flow rate Q. Use ρ = 1000 kg/m³ for water, 13 600 kg/m³ for mercury and g = 9.81 m/s².
A heat engine works between a hot reservoir at 200 °C and a cold reservoir at 10 °C. Find the highest possible thermal efficiency ηmax.
TH = 200 °CTL = 10 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 21 °C while it is -10 °C outside, delivering 12 kW of heat to the house. Find the minimum power input Ẇmin.
TH = 21 °CTL = -10 °CQ̇H = 12 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
An object stands 40 cm in front of a thin converging lens with a focal length of 12 cm. Find the image distance di. Use the sign convention 1/f = 1/do + 1/di (f < 0 for a diverging lens, di < 0 for a virtual image).
do = 40 cmf = 12 cm
di = cm
20.Waves, sound & opticsHard
Light of wavelength 656 nm falls at right angles on a grating with 1200 lines per millimetre. Find the angle θ1 of the order-1 maximum.
N = 1200 mm⁻¹λ = 656 nmm = 1
θ1 = °
3Solutions
1.Kinematics
Answer: t = 7.937 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 100/3.6 = 27.78 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 27.78/3.5 = 7.937 s
Answer
t = 7.937 s
2.Kinematics
Answer: t = 3.273 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−10 = 13·t − ½·9.81·t²
4.905·t² − 13·t − 10 = 0
Solve the quadratic
Only the positive root is physical.
t = (13 + √(13² + 2·9.81·10))/9.81 = 3.273 s
Answer
t = 3.273 s
3.Newton’s laws
Answer: μ = 0.1509
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
a = v₀²/(2d) = 7.5²/(2·19) = 1.48 m/s²
Friction coefficient
μ·m·g = m·a → μ = a/g = 1.48/9.81 = 0.1509
Answer
μ = 0.1509
4.Newton’s laws
Answer: a = 6.332 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 20·cos 25° = 18.13 m/s
vy = v0·sin θ = 20·sin 25° = 8.452 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·8.452/9.81 = 1.723 s
Horizontal distance
x = vx·t = 18.13·1.723 = 31.24 m
Answer
x = 31.24 m
6.Projectile motion
Answer: t = 3.437 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 33·cos 25° = 29.91 m/s
vy = v0·sin θ = 33·sin 25° = 13.95 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 10 + 13.95·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (13.95 + √(194.5 + 196.2))/9.81 = 3.437 s
Answer
t = 3.437 s
7.Work & energy
Answer: d = 39.82 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Speed in base units
v = 90/3.6 = 25 m/s
Energy balance
½mv² = μmg·d → d = v²/(2μg) = 25²/(2·0.8·9.81) = 39.82 m
Answer
d = 39.82 m
Doubling the speed makes the stopping distance four times longer.
8.Work & energy
Answer: v = 4.852 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy released and lost
m₂g·d = 39.24·3 = 117.7 J
μ·m₁g·d = 0.4·29.43·3 = 35.32 J
Kinetic energy of both blocks
½(m₁ + m₂)v² = 82.4 → v = √(2·82.4/7) = 4.852 m/s
Answer
v = 4.852 m/s
9.Momentum & collisions
Answer: ΔK = 120960 J
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 1600·18/3000 = 9.6 m/s
Kinetic energy before and after
Kbefore = ½·1600·18² = 259200 J
Kafter = ½·3000·9.6² = 138240 J
Energy lost
ΔK = 259200 − 138240 = 120960 J
Answer
ΔK = 120960 J
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: θ = 48.37 °
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Momentum components
px = 1200·10 = 12000 kg·m/s
py = 900·15 = 13500 kg·m/s
Direction
tan θ = py/px = 1.125 → θ = 48.37°
Answer
θ = 48.37°
11.Hydrostatic force
Answer: F = 29.43 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 1/2 = 2 m
A = H·b = 1·1.5 = 1.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2·1.5 = 29.43 kN
Answer
F = 29.43 kN
12.Hydrostatic force
Answer: ycp = 5.636 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 3/2 = 5.5 m
A = H·b = 3·2 = 6 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·5.5·6 = 284.9 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Pressure difference from the manometer
Δp = (13600 − 1000)·9.81·0.31 = 38318 Pa
Throat velocity
Continuity and Bernoulli together give the ideal throat velocity.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 313.1 K, T2 = 443.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 20·(300/500)·(443.1/313.1) = 16.98 L
Answer
V2 = 16.98 L
17.Heat engines & refrigerators
Answer: ηmax = 40.16 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 200 + 273.15 = 473.1 K
TL = 10 + 273.15 = 283.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 283.1/473.1 = 40.16 %
Answer
ηmax = 40.16 %
18.Heat engines & refrigerators
Answer: Ẇmin = 1.265 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇H/COP = 12/9.489 = 1.265 kW
Answer
Ẇmin = 1.265 kW
19.Waves, sound & optics
Answer: di = 17.14 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/12 − 1/40
di = 17.14 cm
Ray diagram
real, on the far side of the lens
Answer
di = 17.14 cm
20.Waves, sound & optics
Answer: θ1 = 51.92 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …