Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 54 km/h brakes with a constant deceleration of 7.5 m/s² until it stops. How long does braking take? Find t.
v₀ = 54 km/ha = −7.5 m/s²v = 0
t = s
2.KinematicsHard
A ball is thrown straight up at 6 m/s from the edge of a roof 25 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 6 m/sh₀ = 25 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 3 kg block slides down a slope at 40° to the horizontal. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 3 kgθ = 40°μ = 0.15g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 35° with a speed of 12 m/s. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 12 m/sθ = 35°μ = 0.15g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is launched from level ground at 32 m/s and must land 60 m away. Ignore air resistance and use g = 9.81 m/s². Find the smaller of the two possible launch angles θ.
v₀ = 32 m/sR = 60 mg = 9.81 m/s²
θ = °
6.Projectile motionHard
A ball is thrown from ground level at 29 m/s and 35° above the horizontal. It lands on the flat roof of a building 4 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 29 m/sθ = 35°hroof = 4 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A toy launcher has a vertical spring of stiffness 2000 N/m. A 0.1 kg ball is placed on it and the spring is compressed by 2 cm, then released. Ignoring air resistance and the spring’s mass, find the height h the ball rises, measured from its position when the spring was compressed.
m = 0.1 kgk = 2000 N/mx = 2 cmg = 9.81 m/s²
h = m
8.Work & energyHard
A 2.5 kg block is released from rest at height 1.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 5 m long (μ = 0.1) and then runs onto a spring (k = 5000 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 2.5 kgh = 1.5 mL = 5 mμ = 0.1k = 5000 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 2 kg glider moving at 5 m/s makes a perfectly elastic head-on collision with a 4 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 2 kgm2 = 4 kgv1 = 5 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 1500 kg car runs into a parked 1900 kg car. The wrecks lock together and skid 8.5 m before stopping. The coefficient of kinetic friction between tyres and road is 0.75. Use g = 9.81 m/s². Find the speed v1 of the first car just before the collision.
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of glycerin, with its top edge 4 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water drains from a large open tank through a sharp-edged orifice with a diameter of 20 mm. The water level is kept 5.5 m above the orifice and the discharge coefficient is 0.65. Find the flow rate Q. Use g = 9.81 m/s².
d = 20 mmh = 5.5 mCd = 0.65g = 9.81 m/s²
Q = L/s
14.Continuity & BernoulliHard
Water flows up through a pipe that narrows from 150 mm to 100 mm while rising 10 m. At section 1 the pressure is 280 kPa and the velocity is 1.75 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 725 °C and a cold reservoir at 5 °C. Find the highest possible thermal efficiency ηmax.
TH = 725 °CTL = 5 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A Carnot heat engine receives 60 kW of heat from a source at 950 °C and rejects heat to the surroundings at 20 °C. All of its work drives a Carnot refrigerator that removes heat from a freezer at -30 °C and also rejects heat to the surroundings at 20 °C. Find the rate Q̇L at which heat is removed from the freezer.
TH = 950 °CT0 = 20 °CTL = -30 °CQ̇H = 60 kW
Q̇L = kW
19.Waves, sound & opticsMedium
A string fixed at both ends must have its fundamental (first harmonic) at 188 Hz; waves travel on it at 150 m/s. Find its length L.
v = 150 m/sn = 1f1 = 188 Hz
L = m
20.Waves, sound & opticsHard
An object is 50 cm in front of a concave mirror with a radius of curvature of 24 cm. Find the image distance di, positive for an image in front of the mirror (real) and negative for one behind it (virtual).
do = 50 cmR = 24 cm
di = cm
3Solutions
1.Kinematics
Answer: t = 2 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 54/3.6 = 15 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 15/7.5 = 2 s
Answer
t = 2 s
2.Kinematics
Answer: t = 2.951 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−25 = 6·t − ½·9.81·t²
4.905·t² − 6·t − 25 = 0
Solve the quadratic
Only the positive root is physical.
t = (6 + √(6² + 2·9.81·25))/9.81 = 2.951 s
Answer
t = 2.951 s
3.Newton’s laws
Answer: a = 5.179 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 35° + 0.15·cos 35°) = 6.832 m/s²
Distance
d = v₀²/(2a) = 12²/(2·6.832) = 10.54 m
Answer
d = 10.54 m
5.Projectile motion
Answer: θ = 17.54 °
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Range formula
R = v₀²·sin 2θ/g → sin 2θ = 9.81·60/32² = 0.5748
Angle
2θ = 35.09° → θ = 17.54°
Answer
θ = 17.54°
The other solution is 90° − θ = 72.46°.
6.Projectile motion
Answer: x = 74.37 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 23.76 m/s, vy = 16.63 m/s
Time to land on the roof
Larger root: the ball is descending.
4 = 16.63·t − 4.905·t²
t = (16.63 + √(16.63² − 2·9.81·4))/9.81 = 3.131 s
Horizontal distance
x = vx·t = 23.76·3.131 = 74.37 m
Answer
x = 74.37 m
7.Work & energy
Answer: h = 0.4077 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 2 cm = 0.02 m
½kx² = ½·2000·0.02² = 0.4 J
Height
m·g = 0.1·9.81 = 0.981 N
h = ½kx²/(mg) = 0.4/0.981 = 0.4077 m
Answer
h = 0.4077 m
8.Work & energy
Answer: x = 9.905 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 24.53·(1.5 − 0.1·5) = 24.53 J
Maximum compression
½kx² = 24.53 → x = √(2·24.53/5000) = 0.09905 m = 9.905 cm
Answer
x = 9.905 cm
9.Momentum & collisions
Answer: v′2 = 3.333 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (2 − 4)/(2 + 4)·5 = −1.667 m/s
v′2 = 2·2/(2 + 4)·5 = 3.333 m/s
Answer
v′2 = 3.333 m/s
10.Momentum & collisions
Answer: v1 = 25.35 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Ideal jet velocity
√(2gh) = √(2·9.81·5.5) = 10.39 m/s
Actual flow rate
The discharge coefficient accounts for the contraction of the jet and friction at the edge.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 293.1 K, T2 = 443.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 5·(250/800)·(443.1/293.1) = 2.362 L
Answer
V2 = 2.362 L
17.Heat engines & refrigerators
Answer: ηmax = 72.13 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 725 + 273.15 = 998.1 K
TL = 5 + 273.15 = 278.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 278.1/998.1 = 72.13 %
Answer
ηmax = 72.13 %
18.Heat engines & refrigerators
Answer: Q̇L = 221.8 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 950 + 273.15 = 1223 K
T0 = 20 + 273.15 = 293.1 K
TL = -30 + 273.15 = 243.1 K
Engine work
η = 1 − 293.1/1223 = 0.7603
Ẇ = 0.7603·60 = 45.62 kW
Heat removed by the refrigerator
COPR = 243.1/(293.1 − 243.1) = 4.863
Q̇L = 4.863·45.62 = 221.8 kW
Answer
Q̇L = 221.8 kW
19.Waves, sound & optics
Answer: L = 0.3989 m
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength
λ = v/f = 150/188 = 0.7979 m
Length
L = nλ/2 = 1·0.7979/2 = 0.3989 m
Answer
L = 0.3989 m
20.Waves, sound & optics
Answer: di = 15.79 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.