Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane needs a speed of 180 km/h to take off and the usable runway is 1600 m long. Starting from rest, what constant acceleration a does it need?
v₀ = 0v = 180 km/hs = 1600 m
a = m/s²
2.KinematicsHard
Ball A is dropped from rest from a height of 10 m. At the same instant ball B is thrown straight up from the ground directly below at 14 m/s. Ignore air resistance and use g = 9.81 m/s². When do the balls meet? Find t.
H = 10 mv0B = 14 m/sg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 4 kg block slides down a slope at 30° to the horizontal. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 4 kgθ = 30°μ = 0.2g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 4 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 2 kg mass. The coefficient of kinetic friction between block and table is 0.25. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 4 kgm2 = 2 kgμ = 0.25g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 65° above horizontal from level ground. Ignore air resistance. Find the maximum height H the ball reaches.
v0 = 38 m/sθ = 65°g = 9.81 m/s²
H = m
6.Projectile motionHard
A ball is launched at 15 m/s and 15° above the horizontal from the top of a 15 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the speed v with which it hits the ground.
v₀ = 15 m/sθ = 15°h = 15 mg = 9.81 m/s²
v = m/s
7.Work & energyMedium
A block slides from rest down a slope at 40° to the horizontal. The coefficient of kinetic friction is 0.15. Find its speed v after it has slid 8 m along the slope.
θ = 40°μ = 0.15d = 8 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 4 kg block is released from rest at height 2.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 4.5 m long (μ = 0.2) and then runs onto a spring (k = 2500 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 4 kgh = 2.5 mL = 4.5 mμ = 0.2k = 2500 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 3 kg glider moving at 5 m/s makes a perfectly elastic head-on collision with a 2.5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 3 kgm2 = 2.5 kgv1 = 5 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 0.3 kg ball hits a wall at 28 m/s and bounces straight back at 16 m/s. The contact lasts 10 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.3 kgvin = 28 m/svout = 16 m/sΔt = 10 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 3 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows through a horizontal pipe that narrows from 75 mm to 50 mm. In the wide section the pressure is 330 kPa and the velocity is 3 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 75 mm to 50 mm while rising 10 m. At section 1 the pressure is 400 kPa and the velocity is 0.5 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 650 °C and a cold reservoir at 5 °C. Find the highest possible thermal efficiency ηmax.
TH = 650 °CTL = 5 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A Carnot heat engine receives 60 kW of heat from a source at 550 °C and rejects heat to the surroundings at 20 °C. All of its work drives a Carnot refrigerator that removes heat from a freezer at -20 °C and also rejects heat to the surroundings at 20 °C. Find the rate Q̇L at which heat is removed from the freezer.
TH = 550 °CT0 = 20 °CTL = -20 °CQ̇H = 60 kW
Q̇L = kW
19.Waves, sound & opticsMedium
Light travels in crown glass (n = 1.50) towards a flat boundary with glycerol (n = 1.47). Find the critical angle θc beyond which it is totally reflected.
n1 = 1.50n2 = 1.47
θc = °
20.Waves, sound & opticsHard
An object is 4 cm in front of a convex mirror with a radius of curvature of 30 cm. Find the image distance di, positive for an image in front of the mirror (real) and negative for one behind it (virtual).
do = 4 cmR = 30 cm
di = cm
3Solutions
1.Kinematics
Answer: a = 0.7813 m/s²
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v = 180/3.6 = 50 m/s
Acceleration
a = v²/(2s) = 50²/(2·1600) = 0.7813 m/s²
Answer
a = 0.7813 m/s²
2.Kinematics
Answer: t = 0.7143 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Meeting time
Up is positive, the ground is y = 0.
10 − ½g·t² = 14·t − ½g·t² → t = 10/14 = 0.7143 s
Answer
t = 0.7143 s
3.Newton’s laws
Answer: a = 3.206 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 38·cos 65° = 16.06 m/s
vy = v0·sin θ = 38·sin 65° = 34.44 m/s
Highest point
At the top the vertical velocity is zero: vy² = 2gH.
H = vy²/(2g) = 34.44²/(2·9.81) = 60.45 m
Answer
H = 60.45 m
6.Projectile motion
Answer: v = 22.79 m/s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 15·cos 15° = 14.49 m/s
vy0 = 15·sin 15° = 3.882 m/s
Vertical speed at impact
Energy or v² = v₀² + 2as in the vertical direction.
vy = √(3.882² + 2·9.81·15) = 17.59 m/s
Impact speed
v = √(14.49² + 17.59²) = 22.79 m/s
Answer
v = 22.79 m/s
Check with energy: v² = v₀² + 2gh.
7.Work & energy
Answer: v = 9.103 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·8·(0.6428 − 0.15·0.766)) = 9.103 m/s
Answer
v = 9.103 m/s
8.Work & energy
Answer: x = 22.41 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 39.24·(2.5 − 0.2·4.5) = 62.78 J
Maximum compression
½kx² = 62.78 → x = √(2·62.78/2500) = 0.2241 m = 22.41 cm
Answer
x = 22.41 cm
9.Momentum & collisions
Answer: v′2 = 5.455 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (3 − 2.5)/(3 + 2.5)·5 = 0.4545 m/s
v′2 = 2·3/(3 + 2.5)·5 = 5.455 m/s
Answer
v′2 = 5.455 m/s
10.Momentum & collisions
Answer: J = 13.2 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.3·(16 + 28) = 13.2 N·s
Answer
J = 13.2 N·s
11.Hydrostatic force
Answer: F = 60.7 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 1.5/2 = 2.75 m
A = H·b = 1.5·1.5 = 2.25 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.75·2.25 = 60.7 kN
Answer
F = 60.7 kN
12.Hydrostatic force
Answer: ycp = 4.373 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 2.5/2 = 4.25 m
A = H·b = 2.5·1.5 = 3.75 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·4.25·3.75 = 156.3 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 650 + 273.15 = 923.1 K
TL = 5 + 273.15 = 278.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 278.1/923.1 = 69.87 %
Answer
ηmax = 69.87 %
18.Heat engines & refrigerators
Answer: Q̇L = 244.5 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 550 + 273.15 = 823.1 K
T0 = 20 + 273.15 = 293.1 K
TL = -20 + 273.15 = 253.1 K
Engine work
η = 1 − 293.1/823.1 = 0.6439
Ẇ = 0.6439·60 = 38.63 kW
Heat removed by the refrigerator
COPR = 253.1/(293.1 − 253.1) = 6.329
Q̇L = 6.329·38.63 = 244.5 kW
Answer
Q̇L = 244.5 kW
19.Waves, sound & optics
Answer: θc = 78.52 °
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Refraction at 90°
sin θc = n₂/n₁ = 1.47/1.50 = 0.98
Critical angle
θc = arcsin(0.98) = 78.52°
Answer
θc = 78.52°
20.Waves, sound & optics
Answer: di = −3.158 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.