A DC motor draws 15 A from a 110 V supply. Its armature resistance is 0.25 Ω and its rotational (friction, windage and iron) losses are 128 W. Find its efficiency η.
V = 110 VIa = 15 ARa = 0.25 ΩProt = 128 W
η = %
4.DC motorsHard
A separately excited DC motor (k = 0.75 V·s/rad at full field, Ra = 1.2 Ω, V = 120 V) drives a constant load torque of 3 N·m. The field flux is reduced to 90 % of its full value. Find the new speed n.
Two loads are connected in parallel to a 230 V single-phase supply: a 16 kW load at a power factor of 0.85 lagging and an 18 kW load at a power factor of 0.95 lagging. Find the overall power factor cos φ seen by the supply.
A 50 V (rms), 1000 Hz source has an internal impedance Zs = 8 + j3 Ω. The load impedance ZL can be chosen freely. Find the maximum real power Pmax that can be delivered to the load.
Vs = 50 V (rms)f = 1000 HzZs = 8 + j3 Ω
Pmax = W
7.Three-phase powerMedium
A three-phase induction motor delivers 22 kW of mechanical output power at full load. At this load its efficiency is 88% and its power factor is 0.9 lagging. The supply has a line-to-line voltage of 480 V. Find the line current IL.
Pout = 22 kWη = 88%cos φ = 0.9VL = 480 V
IL = A
8.Three-phase powerHard
A balanced three-phase load takes 50 kW at a power factor of 0.72 lagging from a 480 V (line-to-line), 50 Hz supply. A three-phase capacitor bank in parallel with the load must raise the overall power factor to 0.92 lagging. The real power stays the same. Find the total reactive power QC the capacitor bank must supply, in kvar.
P = 50 kWpf1 = 0.72pf2 = 0.92VL = 480 Vf = 50 Hz
QC = kvar
3Solutions
1.DC-DC converters
Answer: Imax = 1.054 A
DC-DC converters: a switch S turns on for the fraction D of each period T = 1/f. In steady state the average inductor voltage is zero (volt-second balance), which gives the ideal conversion ratios in continuous conduction: buck Vo = D·Vin, boost Vo = Vin/(1 − D), inverting buck-boost |Vo| = Vin·D/(1 − D). An ideal converter keeps the power: Vin·Iin = Vo·Io. While S is on the inductor current rises by ΔIL = VL·D·T/L, with VL = Vin − Vo for the buck and Vin for the boost and buck-boost. The output ripple is ΔVo = ΔIL/(8fC) for the buck and Io·D/(fC) for the boost and buck-boost. The inductor current just touches zero (the CCM boundary) when the average inductor current equals ΔIL/2.
Duty cycle
D = 10.5/15 = 0.7
Average and ripple current
Io = 10.5/12 = 0.875 A
ΔIL = VL·D/(L·f) = 4.5·0.7/(220·10⁻⁶·40·10³) = 0.358 A
Peak current
Imax = 0.875 + 0.358/2 = 1.054 A
Answer
Imax = 1.054 A
2.DC-DC converters
Answer: ΔVo = 83.78 mV
DC-DC converters: a switch S turns on for the fraction D of each period T = 1/f. In steady state the average inductor voltage is zero (volt-second balance), which gives the ideal conversion ratios in continuous conduction: buck Vo = D·Vin, boost Vo = Vin/(1 − D), inverting buck-boost |Vo| = Vin·D/(1 − D). An ideal converter keeps the power: Vin·Iin = Vo·Io. While S is on the inductor current rises by ΔIL = VL·D·T/L, with VL = Vin − Vo for the buck and Vin for the boost and buck-boost. The output ripple is ΔVo = ΔIL/(8fC) for the buck and Io·D/(fC) for the boost and buck-boost. The inductor current just touches zero (the CCM boundary) when the average inductor current equals ΔIL/2.
Duty cycle
D = 7.2/24 = 0.3
Inductor ripple current
ΔIL = (24 − 7.2)·0.3/(100·10⁻⁶·40·10³) = 1.26 A
Output ripple
ΔVo = 1.26/(8·40·10³·47·10⁻⁶) = 83.78 mV
Answer
ΔVo = 83.78 mV
3.DC motors
Answer: η = 88.83 %
DC motor: the armature is a resistance Ra in series with the back-EMF E, so V = E + Ia·Ra. The back-EMF grows with speed, E = k·ω, and the torque with current, T = k·Ia, with the same motor constant k (V·s/rad = N·m/A) in SI units. Convert speeds with ω = 2π·n/60. The developed power is E·Ia = T·ω; the input power is V·Ia, and the copper loss Ia²Ra and the rotational loss make the difference. The speed falls in a straight line with torque, ω = V/k − Ra·T/k², from the no-load speed V/k to zero at the stall torque k·V/Ra. At standstill E = 0, so the starting current V/Ra is large unless a resistor limits it.
Powers
Pin = 110·15 = 1650 W
Pdev = 106.3·15 = 1594 W
Pout = 1594 − 128 = 1466 W
Efficiency
η = 1466/1650·100 = 88.83 %
Answer
η = 88.83 %
4.DC motors
Answer: n = 1622 rpm
DC motor: the armature is a resistance Ra in series with the back-EMF E, so V = E + Ia·Ra. The back-EMF grows with speed, E = k·ω, and the torque with current, T = k·Ia, with the same motor constant k (V·s/rad = N·m/A) in SI units. Convert speeds with ω = 2π·n/60. The developed power is E·Ia = T·ω; the input power is V·Ia, and the copper loss Ia²Ra and the rotational loss make the difference. The speed falls in a straight line with torque, ω = V/k − Ra·T/k², from the no-load speed V/k to zero at the stall torque k·V/Ra. At standstill E = 0, so the starting current V/Ra is large unless a resistor limits it.
Field weakening is how a DC drive runs above its base speed.
5.AC power & power factor
Answer: cos φ = 0.9065
AC power: apparent power S = V·I (VA) splits into real power P = S·cos φ (W), which does useful work, and reactive power Q = S·sin φ (var), which moves back and forth between source and load. The power factor is cos φ. A capacitor in parallel supplies reactive power locally, so the line current drops for the same real power.
Reactive power of each load
A lagging load takes reactive power (Q > 0); a leading load supplies it (Q < 0).
Q1 = 16·tan(arccos 0.85) = 9.916 kvar
Q2 = 18·tan(arccos 0.95) = 5.916 kvar
Totals
P = 16 + 18 = 34 kW
Q = 9.916 + 5.916 = 15.83 kvar
S = √(34² + 15.83²) = 37.51 kVA
Overall power factor
cos φ = P/S = 34/37.51 = 0.9065 lagging
Answer
cos φ = 0.9065
6.AC power & power factor
Answer: Pmax = 78.13 W
AC power: apparent power S = V·I (VA) splits into real power P = S·cos φ (W), which does useful work, and reactive power Q = S·sin φ (var), which moves back and forth between source and load. The power factor is cos φ. A capacitor in parallel supplies reactive power locally, so the line current drops for the same real power.
Conjugate match
The load reactance cancels the source reactance, and the load resistance equals the source resistance.
ZL = Zs* = 8 − j3 Ω
Maximum power
I = Vs/(2Rs) = 50/16 = 3.125 A
Pmax = I²·RL = Vs²/(4Rs) = 50²/(4·8) = 78.13 W
Answer
Pmax = 78.13 W
7.Three-phase power
Answer: IL = 33.41 A
Balanced three-phase systems: in a Y (star) connection the line-to-line voltage is √3 times the phase voltage, VL = √3·Vph, and the line current equals the phase current. In a Δ (delta) connection the line-to-line voltage equals the phase voltage and the line current is √3 times the phase current, IL = √3·Iph. The total power is three times the power of one phase: P = 3·Vph·Iph·cos φ = √3·VL·IL·cos φ.
Electrical input power
Pin = Pout/η = 22/0.88 = 25 kW
Line current
IL = Pin/(√3·VL·cos φ) = 25000/(√3·480·0.9) = 33.41 A
Answer
IL = 33.41 A
8.Three-phase power
Answer: QC = 26.89 kvar
Balanced three-phase systems: in a Y (star) connection the line-to-line voltage is √3 times the phase voltage, VL = √3·Vph, and the line current equals the phase current. In a Δ (delta) connection the line-to-line voltage equals the phase voltage and the line current is √3 times the phase current, IL = √3·Iph. The total power is three times the power of one phase: P = 3·Vph·Iph·cos φ = √3·VL·IL·cos φ. Power factor correction: capacitors supply reactive power locally, QC = P·(tan φ1 − tan φ2). Each of the three capacitors supplies QC/3 = V²·ω·C, where V is the voltage across that capacitor: VL in a Δ bank, VL/√3 in a Y bank.
Reactive power before and after
The real power is unchanged, so each power factor fixes the reactive power: Q = P·tan φ.