Formula sheets, the key method steps for every topic and 10 practice problems, with full solutions at the back.
A balanced Δ-connected load with an impedance of 12 + j5 Ω per phase is connected to a balanced three-phase supply with a line-to-line voltage of 415 V. Find the total real power P absorbed by the load in kW.
A balanced three-phase load takes 200 kW at a power factor of 0.78 lagging from a 480 V (line-to-line), 50 Hz supply. A three-phase capacitor bank in parallel with the load must raise the overall power factor to 0.92 lagging. The real power stays the same. The capacitors are connected in Δ. Find the capacitance Cph of each capacitor in µF.
An ideal transformer with a turns ratio N₁:N₂ = 5:1 has 600 V applied to its primary winding. A 40 Ω resistor is connected across the secondary winding. Find the primary current I1.
A single-phase 50 kVA transformer has a core loss of 400 W and a copper loss of 1000 W at rated load. At what load Sη,max, in kVA, is its efficiency highest?
A single-phase motor takes 22 kW at a power factor of 0.6 lagging from a 400 V supply. Find the reactive power Q it draws.
A single-phase load takes 15 kW at a power factor of 0.6 lagging from a 400 V, 50 Hz supply. A capacitor connected in parallel raises the power factor to 0.9. Find the new line current Inew.
A resistor and a capacitor are connected in parallel across a 120 V (rms), 200 Hz supply. Find the rms current I.
A series RLC circuit is connected to a 100 V (rms), 500 Hz supply. Find the resonant frequency f0 of the circuit.
A DC motor with k = 0.08 V·s/rad runs from 24 V. Neglecting all losses at no load, find its no-load speed n0 in rpm.
A DC chopper feeds a motor (k = 0.3 V·s/rad, Ra = 1.2 Ω) from a 120 V DC bus. The average armature voltage is D·120 V. Find the duty cycle D that runs the motor at 900 rpm with a load of 1.2 N·m.
Answer: P = 36.69 kW
Balanced three-phase systems: in a Y (star) connection the line-to-line voltage is √3 times the phase voltage, VL = √3·Vph, and the line current equals the phase current. In a Δ (delta) connection the line-to-line voltage equals the phase voltage and the line current is √3 times the phase current, IL = √3·Iph. The total power is three times the power of one phase: P = 3·Vph·Iph·cos φ = √3·VL·IL·cos φ.
Only the resistive part of each impedance absorbs real power.
Check: cos φ = R/|Z| = 0.9231, and √3·VL·IL·cos φ gives the same power.
Answer: Cph = 346.6 µF
Balanced three-phase systems: in a Y (star) connection the line-to-line voltage is √3 times the phase voltage, VL = √3·Vph, and the line current equals the phase current. In a Δ (delta) connection the line-to-line voltage equals the phase voltage and the line current is √3 times the phase current, IL = √3·Iph. The total power is three times the power of one phase: P = 3·Vph·Iph·cos φ = √3·VL·IL·cos φ. Power factor correction: capacitors supply reactive power locally, QC = P·(tan φ1 − tan φ2). Each of the three capacitors supplies QC/3 = V²·ω·C, where V is the voltage across that capacitor: VL in a Δ bank, VL/√3 in a Y bank.
The real power is unchanged, so each power factor fixes the reactive power: Q = P·tan φ.
In a Δ bank each capacitor is connected between two lines.
Answer: I1 = 0.6 A
Ideal transformer: the voltages are in the ratio of the turns and the currents in the inverse ratio: V₁/V₂ = N₁/N₂ = a and I₁/I₂ = N₂/N₁ = 1/a, so the power in equals the power out, V₁·I₁ = V₂·I₂. A load impedance Z on the secondary looks like a²·Z from the primary.
An ideal transformer has no losses: V₁·I₁ = V₂·I₂.
Check: the load seen from the primary is a²·RL = 1000 Ω, and 600/1000 gives the same current.
Answer: Sη,max = 31.62 kVA
Transformer losses: the core loss (hysteresis and eddy currents) depends on the voltage and is the same at any load. The copper loss in the windings goes with the current squared, so at a fraction x of rated load it is x²·Pcu,fl. Efficiency η = Pout/(Pout + Pcore + Pcu), with Pout = x·S·pf. The efficiency is highest at the load where the copper loss equals the core loss.
Answer: Q = 29.33 kvar
AC power: apparent power S = V·I (VA) splits into real power P = S·cos φ (W), which does useful work, and reactive power Q = S·sin φ (var), which moves back and forth between source and load. The power factor is cos φ. A capacitor in parallel supplies reactive power locally, so the line current drops for the same real power.
Answer: Inew = 41.67 A
AC power: apparent power S = V·I (VA) splits into real power P = S·cos φ (W), which does useful work, and reactive power Q = S·sin φ (var), which moves back and forth between source and load. The power factor is cos φ. A capacitor in parallel supplies reactive power locally, so the line current drops for the same real power.
The real power P does not change; only the reactive power drawn from the supply does.
Answer: I = 5.031 A
AC circuits with phasors: resistors, inductors and capacitors have impedances R, jωL and 1/(jωC), with ω = 2πf. In series, impedances add like resistances, but as complex numbers. Rms current and voltage follow Ohm’s law with |Z|.
Both branches are connected straight across the supply, so each sees the full voltage V.
The resistor current is in phase with V and the reactive current is 90° out of phase, so they add like the sides of a right triangle.
Answer: f0 = 239.9 Hz
AC circuits with phasors: resistors, inductors and capacitors have impedances R, jωL and 1/(jωC), with ω = 2πf. In series, impedances add like resistances, but as complex numbers. Rms current and voltage follow Ohm’s law with |Z|.
At resonance the inductive and capacitive reactances cancel: ωL = 1/(ωC). The supply frequency does not matter.
Answer: n0 = 2865 rpm
DC motor: the armature is a resistance Ra in series with the back-EMF E, so V = E + Ia·Ra. The back-EMF grows with speed, E = k·ω, and the torque with current, T = k·Ia, with the same motor constant k (V·s/rad = N·m/A) in SI units. Convert speeds with ω = 2π·n/60. The developed power is E·Ia = T·ω; the input power is V·Ia, and the copper loss Ia²Ra and the rotational loss make the difference. The speed falls in a straight line with torque, ω = V/k − Ra·T/k², from the no-load speed V/k to zero at the stall torque k·V/Ra. At standstill E = 0, so the starting current V/Ra is large unless a resistor limits it.
Answer: D = 27.56 %
DC motor: the armature is a resistance Ra in series with the back-EMF E, so V = E + Ia·Ra. The back-EMF grows with speed, E = k·ω, and the torque with current, T = k·Ia, with the same motor constant k (V·s/rad = N·m/A) in SI units. Convert speeds with ω = 2π·n/60. The developed power is E·Ia = T·ω; the input power is V·Ia, and the copper loss Ia²Ra and the rotational loss make the difference. The speed falls in a straight line with torque, ω = V/k − Ra·T/k², from the no-load speed V/k to zero at the stall torque k·V/Ra. At standstill E = 0, so the starting current V/Ra is large unless a resistor limits it.
ExamProblems · examproblems.com/courses/power-systems