Power Systems and Electrical Machines: cram pack

Formula sheets, the key method steps for every topic and 10 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Three-phase power

Y connection
VL = √3·Vph, IL = Iph
Δ connection
VL = Vph, IL = √3·Iph
Total real power
P = √3·VL·IL·cos φ = 3·Iph²·R
Apparent and reactive power
S = √3·VL·IL, Q = P·tan φ
Correction capacitors
QC = P(tan φ1 − tan φ2), C = QC/(3ωV²)
Voltage across each capacitor
Δ: VL Y: VL/√3
Motor input
Pin = Pout/η

Transformers

Turns ratio
a = N1/N2 = V1/V2
Current ratio
I1/I2 = N2/N1 = 1/a
Rated current
I = S/V
Referred impedance
Z1′ = a²·ZL
Copper loss at part load
Pcu = x²·Pcu,fl
Efficiency
η = x·S·pf/(x·S·pf + Pcore + x²·Pcu,fl)
Maximum efficiency
x = √(Pcore/Pcu,fl)

AC power & power factor

Real power
P = V·I·cos φ
Reactive power
Q = V·I·sin φ
Apparent power
S = V·I = √(P² + Q²)
Power factor
pf = cos φ = P/S
Correction capacitor
QC = P(tan φ1 − tan φ2), C = QC/(ωV²)

AC impedance & phasors

Impedances
ZR = R, ZL = jωL, ZC = 1/(jωC)
Angular frequency
ω = 2πf
Magnitude and angle
|Z| = √(R² + X²), φ = atan(X/R)
Phasor Ohm’s law
V = I·Z

Method

  1. Convert the frequency: ω = 2πf.
  2. Find each reactance: XL = ωL and XC = 1/(ωC).
  3. Add impedances like resistors, with Z = R + jX.
  4. Find the magnitude |Z| = √(R² + X²) and the angle φ = atan(X/R), then use Ohm’s law with phasors.

DC motors

Armature circuit
V = E + IaRa
Back-EMF and torque
E = k·ω, T = k·Ia
Speed
ω = 2π·n/60, ω = (V − IaRa)/k
No-load speed and stall torque
ω0 = V/k, Tstall = k·V/Ra
Powers
Pin = V·Ia, Pdev = E·Ia = T·ω, Pout = Pdev − Prot
Starting
Istart = V/(Ra + Rst)
Speed regulation
SR = (n0 − nFL)/nFL
Maximum developed power
Pmax = V²/(4Ra)
Chopper drive
Va = D·Vdc

Method

  1. Draw the armature circuit: supply V, resistance Ra and the back-EMF E in series.
  2. Use V = E + Ia·Ra to link voltage, current and back-EMF.
  3. Use E = k·ω for speed and T = k·Ia for torque, with ω = 2π·n/60.
  4. For power and efficiency, start from V·Ia, subtract the copper loss Ia²·Ra and then the rotational losses.

2Practice problems

1.Three-phase powerMedium
ABCVL​ = 480 VIL​ = ?M110 kW, η = 92%cos φ = 0.88

A three-phase induction motor delivers 110 kW of mechanical output power at full load. At this load its efficiency is 92% and its power factor is 0.88 lagging. The supply has a line-to-line voltage of 480 V. Find the line current IL.

Pout = 110 kWη = 92%cos φ = 0.88VL = 480 V
IL = A
2.Three-phase powerHard
P = 100 kWφ1​S1​Q2​QC​ = ?

A balanced three-phase load takes 100 kW at a power factor of 0.72 lagging from a 400 V (line-to-line), 60 Hz supply. A three-phase capacitor bank in parallel with the load must raise the overall power factor to 0.9 lagging. The real power stays the same. Find the total reactive power QC the capacitor bank must supply, in kvar.

P = 100 kWpf1 = 0.72pf2 = 0.9VL = 400 Vf = 60 Hz
QC = kvar
3.TransformersMedium
RL​ = 12 Ω51600 VV2​I1​ = ?I2​

An ideal transformer with a turns ratio N₁:N₂ = 5:1 has 600 V applied to its primary winding. A 12 Ω resistor is connected across the secondary winding. Find the primary current I1.

N1:N2 = 5:1V1 = 600 VRL = 12 Ω
I1 = A
4.TransformersHard
pf 0.9500 kVA, 75% load

A single-phase 500 kVA transformer has a core loss of 3000 W and a copper loss of 4500 W at rated load. It supplies 75% of its rated kVA at a power factor of 0.9 lagging. Find the total losses Ploss in watts at this load.

S = 500 kVAPcore = 3000 WPcu,fl = 4500 Wx = 0.75pf = 0.9
Ploss = W
5.AC power & power factorMedium
230 VZ12 + j9 ΩI

A load with impedance Z = 12 + j9 Ω is connected to a 230 V (rms) single-phase supply. Find the apparent power S.

V = 230 VZ = 12 + j9 Ω
S = VA
6.AC power & power factorHard
P = 30 kWQ1​S1​φ1​QC​

A single-phase load takes 30 kW at a power factor of 0.8 lagging from a 240 V, 50 Hz supply. A capacitor connected in parallel raises the power factor to 0.92. Find the reactive power QC the capacitor must supply.

P = 30 kWpf1 = 0.8pf2 = 0.92V = 240 Vf = 50 Hz
QC = kvar
7.AC impedance & phasorsMedium
10 V200 HzR = 60 ΩL = 200 mHC = 1 µF

A series RLC circuit is connected to a 10 V (rms), 200 Hz supply. Find the phase angle φ of the impedance, in degrees (positive when the current lags the voltage).

V = 10 V (rms)f = 200 HzR = 60 ΩL = 200 mHC = 1 µF
φ = °
8.AC impedance & phasorsHard
50 V200 HzR1​ = 50 ΩR2​ = 30 ΩC = 47 µF

A resistor R1 is connected in series with a parallel combination of R2 and a capacitor C, across a 50 V (rms), 200 Hz supply. Find the magnitude of the impedance |Z|.

V = 50 V (rms)f = 200 HzR1 = 50 ΩR2 = 30 ΩC = 47 µF
|Z| = Ω
9.DC motorsMedium
+−VRa​M+−En = 1000 rpmT = ?

A DC motor delivers 2.2 kW of mechanical power at 1000 rpm. Find the shaft torque T.

P = 2.2 kWn = 1000 rpm
T = N·m
10.DC motorsHard
+−48 VRa​ = 0.8 ΩM+−EωT

A small DC motor has an armature resistance of 0.8 Ω and runs from 48 V. Neglecting rotational losses, find the largest mechanical power Pmax it can develop at any speed.

V = 48 VRa = 0.8 Ω
Pmax = W

3Solutions

1.Three-phase power

Answer: IL = 163.4 A

Balanced three-phase systems: in a Y (star) connection the line-to-line voltage is √3 times the phase voltage, VL = √3·Vph, and the line current equals the phase current. In a Δ (delta) connection the line-to-line voltage equals the phase voltage and the line current is √3 times the phase current, IL = √3·Iph. The total power is three times the power of one phase: P = 3·Vph·Iph·cos φ = √3·VL·IL·cos φ.

Electrical input power

Pin = Pout/η = 110/0.92 = 119.6 kW

Line current

IL = Pin/(√3·VL·cos φ) = 119565/(√3·480·0.88) = 163.4 A

Answer

IL = 163.4 A
2.Three-phase power

Answer: QC = 47.95 kvar

Balanced three-phase systems: in a Y (star) connection the line-to-line voltage is √3 times the phase voltage, VL = √3·Vph, and the line current equals the phase current. In a Δ (delta) connection the line-to-line voltage equals the phase voltage and the line current is √3 times the phase current, IL = √3·Iph. The total power is three times the power of one phase: P = 3·Vph·Iph·cos φ = √3·VL·IL·cos φ. Power factor correction: capacitors supply reactive power locally, QC = P·(tan φ1 − tan φ2). Each of the three capacitors supplies QC/3 = V²·ω·C, where V is the voltage across that capacitor: VL in a Δ bank, VL/√3 in a Y bank.

Reactive power before and after

The real power is unchanged, so each power factor fixes the reactive power: Q = P·tan φ.

Q1 = 100·tan(acos 0.72) = 100·0.9639 = 96.39 kvar
Q2 = 100·tan(acos 0.9) = 100·0.4843 = 48.43 kvar

Reactive power from the capacitors

QC = Q1 − Q2 = 47.95 kvar

Answer

QC = 47.95 kvar
3.Transformers

Answer: I1 = 2 A

Ideal transformer: the voltages are in the ratio of the turns and the currents in the inverse ratio: V₁/V₂ = N₁/N₂ = a and I₁/I₂ = N₂/N₁ = 1/a, so the power in equals the power out, V₁·I₁ = V₂·I₂. A load impedance Z on the secondary looks like a²·Z from the primary.

Secondary voltage and current

V2 = 600/5 = 120 V
I2 = 120/12 = 10 A

Primary current

An ideal transformer has no losses: V₁·I₁ = V₂·I₂.

I1 = I2/5 = 2 A

Answer

I1 = 2 A

Check: the load seen from the primary is a²·RL = 300 Ω, and 600/300 gives the same current.

4.Transformers

Answer: Ploss = 5531 W

Transformer losses: the core loss (hysteresis and eddy currents) depends on the voltage and is the same at any load. The copper loss in the windings goes with the current squared, so at a fraction x of rated load it is x²·Pcu,fl. Efficiency η = Pout/(Pout + Pcore + Pcu), with Pout = x·S·pf. The efficiency is highest at the load where the copper loss equals the core loss.

Copper loss at this load

Pcu = x²·Pcu,fl = 0.5625·4500 = 2531 W

Total losses

The core loss is the same at any load.

Ploss = 3000 + 2531 = 5531 W

Answer

Ploss = 5531 W

The efficiency at this load is η = 98.39%.

5.AC power & power factor

Answer: S = 3527 VA

AC power: apparent power S = V·I (VA) splits into real power P = S·cos φ (W), which does useful work, and reactive power Q = S·sin φ (var), which moves back and forth between source and load. The power factor is cos φ. A capacitor in parallel supplies reactive power locally, so the line current drops for the same real power.

Current

|Z| = √(12² + 9²) = 15 Ω
I = V/|Z| = 230/15 = 15.33 A

Apparent power

S = V·I = 230·15.33 = 3527 VA

Answer

S = 3527 VA
6.AC power & power factor

Answer: QC = 9.72 kvar

AC power: apparent power S = V·I (VA) splits into real power P = S·cos φ (W), which does useful work, and reactive power Q = S·sin φ (var), which moves back and forth between source and load. The power factor is cos φ. A capacitor in parallel supplies reactive power locally, so the line current drops for the same real power.

Reactive power before and after

The real power P does not change; only the reactive power drawn from the supply does.

Q1 = P·tan φ1 = 30·tan(36.87°) = 22.5 kvar
Q2 = P·tan φ2 = 30·tan(23.07°) = 12.78 kvar
QC = Q1 − Q2 = 9.72 kvar

Answer

QC = 9.72 kvar
7.AC impedance & phasors

Answer: φ = −83.71 °

AC circuits with phasors: resistors, inductors and capacitors have impedances R, jωL and 1/(jωC), with ω = 2πf. In series, impedances add like resistances, but as complex numbers. Rms current and voltage follow Ohm’s law with |Z|.

Reactances

ω = 2πf = 2π·200 = 1257 rad/s
XL = ωL = 1257·0.2 = 251.3 Ω
XC = 1/(ωC) = 1/(1257·1·10⁻⁶) = 795.8 Ω

Impedance

In series the impedances add as complex numbers: Z = R + j(XL − XC).

|Z| = √(R² + (XL − XC)²) = √(60² + (−544.4)²) = 547.7 Ω

Phase angle

φ = arctan((XL − XC)/R) = arctan(−544.4/60) = −83.71°

Answer

φ = −83.71°
8.AC impedance & phasors

Answer: |Z| = 58.67 Ω

AC circuits with phasors: resistors, inductors and capacitors have impedances R, jωL and 1/(jωC), with ω = 2πf. In series, impedances add like resistances, but as complex numbers. Rms current and voltage follow Ohm’s law with |Z|.

Reactance

XC = 1/(2π·200·47·10⁻⁶) = 16.93 Ω

Parallel combination

Multiply top and bottom by the complex conjugate to split Zp into real and imaginary parts.

Zp = R₂·(−jXC)/(R₂ − jXC) = (R₂·XC² − jR₂²·XC)/(R₂² + XC²)
Zp = 7.247 − j12.84 Ω

Total impedance

Z = 50 + 7.247 − j12.84 = 57.25 − j12.84 Ω
|Z| = √(57.25² + 12.84²) = 58.67 Ω

Answer

|Z| = 58.67 Ω
9.DC motors

Answer: T = 21.01 N·m

DC motor: the armature is a resistance Ra in series with the back-EMF E, so V = E + Ia·Ra. The back-EMF grows with speed, E = k·ω, and the torque with current, T = k·Ia, with the same motor constant k (V·s/rad = N·m/A) in SI units. Convert speeds with ω = 2π·n/60. The developed power is E·Ia = T·ω; the input power is V·Ia, and the copper loss Ia²Ra and the rotational loss make the difference. The speed falls in a straight line with torque, ω = V/k − Ra·T/k², from the no-load speed V/k to zero at the stall torque k·V/Ra. At standstill E = 0, so the starting current V/Ra is large unless a resistor limits it.

Speed in rad/s

ω = 2π·1000/60 = 104.7 rad/s

Torque

T = P/ω = 2200/104.7 = 21.01 N·m

Answer

T = 21.01 N·m
10.DC motors

Answer: Pmax = 720 W

DC motor: the armature is a resistance Ra in series with the back-EMF E, so V = E + Ia·Ra. The back-EMF grows with speed, E = k·ω, and the torque with current, T = k·Ia, with the same motor constant k (V·s/rad = N·m/A) in SI units. Convert speeds with ω = 2π·n/60. The developed power is E·Ia = T·ω; the input power is V·Ia, and the copper loss Ia²Ra and the rotational loss make the difference. The speed falls in a straight line with torque, ω = V/k − Ra·T/k², from the no-load speed V/k to zero at the stall torque k·V/Ra. At standstill E = 0, so the starting current V/Ra is large unless a resistor limits it.

Power as a function of the back-EMF

P(E) = E·(V − E)/Ra
dP/dE = 0 → E = V/2 = 24 V

Maximum power

Pmax = (V/2)²/Ra = V²/(4Ra) = 48²/(4·0.8) = 720 W

Answer

Pmax = 720 W

At this point the efficiency is only 50 %, so real motors run well above half speed.

ExamProblems · examproblems.com/courses/power-systems