Power Systems and Electrical Machines: cram pack

Formula sheets, the key method steps for every topic and 10 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Three-phase power

Y connection
VL = √3·Vph, IL = Iph
Δ connection
VL = Vph, IL = √3·Iph
Total real power
P = √3·VL·IL·cos φ = 3·Iph²·R
Apparent and reactive power
S = √3·VL·IL, Q = P·tan φ
Correction capacitors
QC = P(tan φ1 − tan φ2), C = QC/(3ωV²)
Voltage across each capacitor
Δ: VL Y: VL/√3
Motor input
Pin = Pout/η

Transformers

Turns ratio
a = N1/N2 = V1/V2
Current ratio
I1/I2 = N2/N1 = 1/a
Rated current
I = S/V
Referred impedance
Z1′ = a²·ZL
Copper loss at part load
Pcu = x²·Pcu,fl
Efficiency
η = x·S·pf/(x·S·pf + Pcore + x²·Pcu,fl)
Maximum efficiency
x = √(Pcore/Pcu,fl)

AC power & power factor

Real power
P = V·I·cos φ
Reactive power
Q = V·I·sin φ
Apparent power
S = V·I = √(P² + Q²)
Power factor
pf = cos φ = P/S
Correction capacitor
QC = P(tan φ1 − tan φ2), C = QC/(ωV²)

AC impedance & phasors

Impedances
ZR = R, ZL = jωL, ZC = 1/(jωC)
Angular frequency
ω = 2πf
Magnitude and angle
|Z| = √(R² + X²), φ = atan(X/R)
Phasor Ohm’s law
V = I·Z

Method

  1. Convert the frequency: ω = 2πf.
  2. Find each reactance: XL = ωL and XC = 1/(ωC).
  3. Add impedances like resistors, with Z = R + jX.
  4. Find the magnitude |Z| = √(R² + X²) and the angle φ = atan(X/R), then use Ohm’s law with phasors.

DC motors

Armature circuit
V = E + IaRa
Back-EMF and torque
E = k·ω, T = k·Ia
Speed
ω = 2π·n/60, ω = (V − IaRa)/k
No-load speed and stall torque
ω0 = V/k, Tstall = k·V/Ra
Powers
Pin = V·Ia, Pdev = E·Ia = T·ω, Pout = Pdev − Prot
Starting
Istart = V/(Ra + Rst)
Speed regulation
SR = (n0 − nFL)/nFL
Maximum developed power
Pmax = V²/(4Ra)
Chopper drive
Va = D·Vdc

Method

  1. Draw the armature circuit: supply V, resistance Ra and the back-EMF E in series.
  2. Use V = E + Ia·Ra to link voltage, current and back-EMF.
  3. Use E = k·ω for speed and T = k·Ia for torque, with ω = 2π·n/60.
  4. For power and efficiency, start from V·Ia, subtract the copper loss Ia²·Ra and then the rotational losses.

2Practice problems

1.Three-phase powerMedium
ABCVL​ = 415 VNZ = 3 + j4 Ωper phase

A balanced Y-connected load with an impedance of 3 + j4 Ω per phase is connected to a balanced three-phase supply with a line-to-line voltage of 415 V. Find the total real power P absorbed by the load in kW.

VL = 415 VZ = 3 + j4 Ω per phase
P = kW
2.Three-phase powerHard
P = 200 kWφ1​S1​Q2​QC​

A balanced three-phase load takes 200 kW at a power factor of 0.8 lagging from a 400 V (line-to-line), 60 Hz supply. A three-phase capacitor bank in parallel with the load must raise the overall power factor to 0.98 lagging. The real power stays the same. The capacitors are connected in Y. Find the capacitance Cph of each capacitor in µF.

P = 200 kWpf1 = 0.8pf2 = 0.98VL = 400 Vf = 60 Hz
Cph = µF
3.TransformersMedium
2 Ω51

A 2 Ω resistor is connected across the secondary winding of an ideal transformer with a turns ratio N₁:N₂ = 5:1. Find the resistance R1′ seen looking into the primary winding.

N1:N2 = 5:1RL = 2 Ω
R1′ = Ω
4.TransformersHard
pf 0.9250 kVA, 50% load

A single-phase 250 kVA transformer has a core loss of 1000 W and a copper loss of 3000 W at rated load. It supplies 50% of its rated kVA at a power factor of 0.9 lagging. Find the total losses Ploss in watts at this load.

S = 250 kVAPcore = 1000 WPcu,fl = 3000 Wx = 0.5pf = 0.9
Ploss = W
5.AC power & power factorMedium
240 VZ9 + j12 ΩI

A load with impedance Z = 9 + j12 Ω is connected to a 240 V (rms) single-phase supply. Find the apparent power S.

V = 240 VZ = 9 + j12 Ω
S = VA
6.AC power & power factorHard
P = 40 kWQ1​S1​φ1​QC​

A single-phase load takes 40 kW at a power factor of 0.7 lagging from a 230 V, 60 Hz supply. A capacitor connected in parallel raises the power factor to 0.95. Find the new line current Inew.

P = 40 kWpf1 = 0.7pf2 = 0.95V = 230 Vf = 60 Hz
Inew = A
7.AC impedance & phasorsMedium
12 V100 HzR = 30 ΩL = 250 mHC = 47 µFI

A series RLC circuit is connected to a 12 V (rms), 100 Hz supply. Find the real power P taken from the supply.

V = 12 V (rms)f = 100 HzR = 30 ΩL = 250 mHC = 47 µF
P = W
8.AC impedance & phasorsHard
10 Vf0​R = 2 ΩL = 20 mHC = 4.7 µF

A series RLC circuit is driven by a 10 V (rms) source whose frequency is set to the resonant frequency of the circuit. Find the rms voltage VL across the inductor.

V = 10 V (rms)R = 2 ΩL = 20 mHC = 4.7 µF
VL = V
9.DC motorsMedium
+−110 VRa​ = 1.2 ΩIa​ = 6 AM+−EωT

A DC motor draws 6 A from a 110 V supply. Its armature resistance is 1.2 Ω and its rotational (friction, windage and iron) losses are 37 W. Find its efficiency η.

V = 110 VIa = 6 ARa = 1.2 ΩProt = 37 W
η = %
10.DC motorsHard
+−220 VRs​ = ?Ra​ = 1.5 ΩM+−En = 300 rpmT = 9 N·m

A DC motor (k = 1.5 V·s/rad, Ra = 1.5 Ω) on a fixed 220 V supply drives a load of 9 N·m. Find the series resistance Rs that slows it down to 300 rpm.

V = 220 Vk = 1.5 V·s/radRa = 1.5 ΩT = 9 N·mn = 300 rpm
Rs = Ω

3Solutions

1.Three-phase power

Answer: P = 20.67 kW

Balanced three-phase systems: in a Y (star) connection the line-to-line voltage is √3 times the phase voltage, VL = √3·Vph, and the line current equals the phase current. In a Δ (delta) connection the line-to-line voltage equals the phase voltage and the line current is √3 times the phase current, IL = √3·Iph. The total power is three times the power of one phase: P = 3·Vph·Iph·cos φ = √3·VL·IL·cos φ.

Phase voltage

Vph = 415/√3 = 239.6 V

Phase current

|Z| = √(3² + 4²) = 5 Ω
Iph = 239.6/5 = 47.92 A

Total real power

Only the resistive part of each impedance absorbs real power.

P = 3·Iph²·R = 3·47.92²·3 = 20.67 kW

Answer

P = 20.67 kW

Check: cos φ = R/|Z| = 0.6, and √3·VL·IL·cos φ gives the same power.

2.Three-phase power

Answer: Cph = 1814 µF

Balanced three-phase systems: in a Y (star) connection the line-to-line voltage is √3 times the phase voltage, VL = √3·Vph, and the line current equals the phase current. In a Δ (delta) connection the line-to-line voltage equals the phase voltage and the line current is √3 times the phase current, IL = √3·Iph. The total power is three times the power of one phase: P = 3·Vph·Iph·cos φ = √3·VL·IL·cos φ. Power factor correction: capacitors supply reactive power locally, QC = P·(tan φ1 − tan φ2). Each of the three capacitors supplies QC/3 = V²·ω·C, where V is the voltage across that capacitor: VL in a Δ bank, VL/√3 in a Y bank.

Reactive power before and after

The real power is unchanged, so each power factor fixes the reactive power: Q = P·tan φ.

Q1 = 200·tan(acos 0.8) = 200·0.75 = 150 kvar
Q2 = 200·tan(acos 0.98) = 200·0.2031 = 40.61 kvar

Reactive power from the capacitors

QC = Q1 − Q2 = 109.4 kvar

Capacitance per phase

In a Y bank each capacitor is connected between a line and the star point.

V = 400/√3 = 230.9 V, ω = 2π·60 = 377 rad/s
Cph = (QC/3)/(ω·V²) = 36463/(377·230.9²) = 1814 µF

Answer

Cph = 1814 µF
3.Transformers

Answer: R1′ = 50 Ω

Ideal transformer: the voltages are in the ratio of the turns and the currents in the inverse ratio: V₁/V₂ = N₁/N₂ = a and I₁/I₂ = N₂/N₁ = 1/a, so the power in equals the power out, V₁·I₁ = V₂·I₂. A load impedance Z on the secondary looks like a²·Z from the primary.

Referred resistance

The voltage goes up by a and the current down by a, so the ratio V/I goes up by a².

R1′ = a²·RL = 5²·2 = 50 Ω

Answer

R1′ = 50 Ω
4.Transformers

Answer: Ploss = 1750 W

Transformer losses: the core loss (hysteresis and eddy currents) depends on the voltage and is the same at any load. The copper loss in the windings goes with the current squared, so at a fraction x of rated load it is x²·Pcu,fl. Efficiency η = Pout/(Pout + Pcore + Pcu), with Pout = x·S·pf. The efficiency is highest at the load where the copper loss equals the core loss.

Copper loss at this load

Pcu = x²·Pcu,fl = 0.25·3000 = 750 W

Total losses

The core loss is the same at any load.

Ploss = 1000 + 750 = 1750 W

Answer

Ploss = 1750 W

The efficiency at this load is η = 98.47%.

5.AC power & power factor

Answer: S = 3840 VA

AC power: apparent power S = V·I (VA) splits into real power P = S·cos φ (W), which does useful work, and reactive power Q = S·sin φ (var), which moves back and forth between source and load. The power factor is cos φ. A capacitor in parallel supplies reactive power locally, so the line current drops for the same real power.

Current

|Z| = √(9² + 12²) = 15 Ω
I = V/|Z| = 240/15 = 16 A

Apparent power

S = V·I = 240·16 = 3840 VA

Answer

S = 3840 VA
6.AC power & power factor

Answer: Inew = 183.1 A

AC power: apparent power S = V·I (VA) splits into real power P = S·cos φ (W), which does useful work, and reactive power Q = S·sin φ (var), which moves back and forth between source and load. The power factor is cos φ. A capacitor in parallel supplies reactive power locally, so the line current drops for the same real power.

Reactive power before and after

The real power P does not change; only the reactive power drawn from the supply does.

Q1 = P·tan φ1 = 40·tan(45.57°) = 40.81 kvar
Q2 = P·tan φ2 = 40·tan(18.19°) = 13.15 kvar
QC = Q1 − Q2 = 27.66 kvar

New line current

Inew = P/(V·cos φ2) = 40000/(230·0.95) = 183.1 A

Answer

Inew = 183.1 A
7.AC impedance & phasors

Answer: P = 0.2686 W

AC circuits with phasors: resistors, inductors and capacitors have impedances R, jωL and 1/(jωC), with ω = 2πf. In series, impedances add like resistances, but as complex numbers. Rms current and voltage follow Ohm’s law with |Z|.

Reactances

XL = 157.1 Ω, XC = 33.86 Ω

Impedance

|Z| = √(30² + (123.2)²) = 126.8 Ω

Real power

Inductors and capacitors only store and return energy; the resistor absorbs all of the real power.

I = 12/126.8 = 0.09462 A
P = I²·R = 0.09462²·30 = 0.2686 W

Answer

P = 0.2686 W
8.AC impedance & phasors

Answer: VL = 326.2 V

AC circuits with phasors: resistors, inductors and capacitors have impedances R, jωL and 1/(jωC), with ω = 2πf. In series, impedances add like resistances, but as complex numbers. Rms current and voltage follow Ohm’s law with |Z|.

Resonance

At resonance the reactances cancel, so the impedance is just R.

ω₀ = 1/√(LC) = 1/√(0.02·4.7·10⁻⁶) = 3262 rad/s
I = V/R = 10/2 = 5 A

Voltage across the inductor

XL = ω₀L = 3262·0.02 = 65.23 Ω
VL = I·XL = 5·65.23 = 326.2 V

Answer

VL = 326.2 V

This is Q = 32.62 times the supply voltage.

9.DC motors

Answer: η = 87.85 %

DC motor: the armature is a resistance Ra in series with the back-EMF E, so V = E + Ia·Ra. The back-EMF grows with speed, E = k·ω, and the torque with current, T = k·Ia, with the same motor constant k (V·s/rad = N·m/A) in SI units. Convert speeds with ω = 2π·n/60. The developed power is E·Ia = T·ω; the input power is V·Ia, and the copper loss Ia²Ra and the rotational loss make the difference. The speed falls in a straight line with torque, ω = V/k − Ra·T/k², from the no-load speed V/k to zero at the stall torque k·V/Ra. At standstill E = 0, so the starting current V/Ra is large unless a resistor limits it.

Powers

Pin = 110·6 = 660 W
Pdev = 102.8·6 = 616.8 W
Pout = 616.8 − 37 = 579.8 W

Efficiency

η = 579.8/660·100 = 87.85 %

Answer

η = 87.85 %
10.DC motors

Answer: Rs = 27.31 Ω

DC motor: the armature is a resistance Ra in series with the back-EMF E, so V = E + Ia·Ra. The back-EMF grows with speed, E = k·ω, and the torque with current, T = k·Ia, with the same motor constant k (V·s/rad = N·m/A) in SI units. Convert speeds with ω = 2π·n/60. The developed power is E·Ia = T·ω; the input power is V·Ia, and the copper loss Ia²Ra and the rotational loss make the difference. The speed falls in a straight line with torque, ω = V/k − Ra·T/k², from the no-load speed V/k to zero at the stall torque k·V/Ra. At standstill E = 0, so the starting current V/Ra is large unless a resistor limits it.

Current and back-EMF

Ia = 9/1.5 = 6 A
E = 1.5·31.42 = 47.12 V

Series resistance

Ra + Rs = (220 − 47.12)/6 = 28.81 Ω
Rs = 27.31 Ω

Answer

Rs = 27.31 Ω

The resistor wastes 983.3 W; a chopper controls the speed with far less loss.

ExamProblems · examproblems.com/courses/power-systems