In the print window, choose “Save as PDF” to keep a copy on your device.
1Formulas and methods
Three-phase power
Y connection
VL = √3·Vph, IL = Iph
Δ connection
VL = Vph, IL = √3·Iph
Total real power
P = √3·VL·IL·cos φ = 3·Iph²·R
Apparent and reactive power
S = √3·VL·IL, Q = P·tan φ
Correction capacitors
QC = P(tan φ1 − tan φ2), C = QC/(3ωV²)
Voltage across each capacitor
Δ: VL Y: VL/√3
Motor input
Pin = Pout/η
Transformers
Turns ratio
a = N1/N2 = V1/V2
Current ratio
I1/I2 = N2/N1 = 1/a
Rated current
I = S/V
Referred impedance
Z1′ = a²·ZL
Copper loss at part load
Pcu = x²·Pcu,fl
Efficiency
η = x·S·pf/(x·S·pf + Pcore + x²·Pcu,fl)
Maximum efficiency
x = √(Pcore/Pcu,fl)
AC power & power factor
Real power
P = V·I·cos φ
Reactive power
Q = V·I·sin φ
Apparent power
S = V·I = √(P² + Q²)
Power factor
pf = cos φ = P/S
Correction capacitor
QC = P(tan φ1 − tan φ2), C = QC/(ωV²)
AC impedance & phasors
Impedances
ZR = R, ZL = jωL, ZC = 1/(jωC)
Angular frequency
ω = 2πf
Magnitude and angle
|Z| = √(R² + X²), φ = atan(X/R)
Phasor Ohm’s law
V = I·Z
Method
Convert the frequency: ω = 2πf.
Find each reactance: XL = ωL and XC = 1/(ωC).
Add impedances like resistors, with Z = R + jX.
Find the magnitude |Z| = √(R² + X²) and the angle φ = atan(X/R), then use Ohm’s law with phasors.
DC motors
Armature circuit
V = E + IaRa
Back-EMF and torque
E = k·ω, T = k·Ia
Speed
ω = 2π·n/60, ω = (V − IaRa)/k
No-load speed and stall torque
ω0 = V/k, Tstall = k·V/Ra
Powers
Pin = V·Ia, Pdev = E·Ia = T·ω, Pout = Pdev − Prot
Starting
Istart = V/(Ra + Rst)
Speed regulation
SR = (n0 − nFL)/nFL
Maximum developed power
Pmax = V²/(4Ra)
Chopper drive
Va = D·Vdc
Method
Draw the armature circuit: supply V, resistance Ra and the back-EMF E in series.
Use V = E + Ia·Ra to link voltage, current and back-EMF.
Use E = k·ω for speed and T = k·Ia for torque, with ω = 2π·n/60.
For power and efficiency, start from V·Ia, subtract the copper loss Ia²·Ra and then the rotational losses.
2Practice problems
1.Three-phase powerMedium
A balanced Δ-connected load with an impedance of 18 + j24 Ω per phase is connected to a balanced three-phase supply with a line-to-line voltage of 400 V. Find the total real power P absorbed by the load in kW.
VL = 400 VZ = 18 + j24 Ω per phase
P = kW
2.Three-phase powerHard
A balanced three-phase load takes 50 kW at a power factor of 0.8 lagging from a 690 V (line-to-line), 50 Hz supply. A three-phase capacitor bank in parallel with the load must raise the overall power factor to 0.95 lagging. The real power stays the same. The capacitors are connected in Δ. Find the capacitance Cph of each capacitor in µF.
P = 50 kWpf1 = 0.8pf2 = 0.95VL = 690 Vf = 50 Hz
Cph = µF
3.TransformersMedium
An ideal transformer with a turns ratio N₁:N₂ = 4:1 has 480 V applied to its primary winding. A 30 Ω resistor is connected across the secondary winding. Find the primary current I1.
N1:N2 = 4:1V1 = 480 VRL = 30 Ω
I1 = A
4.TransformersHard
A single-phase 50 kVA transformer has a core loss of 150 W and a copper loss of 225 W at rated load. At what load Sη,max, in kVA, is its efficiency highest?
S = 50 kVAPcore = 150 WPcu,fl = 225 W
Sη,max = kVA
5.AC power & power factorMedium
An inductive load takes 11.5 A and 1104 W from a 120 V (rms) single-phase supply. Model it as a resistance R in series with a reactance X. Find R.
V = 120 VI = 11.5 AP = 1104 W
R = Ω
6.AC power & power factorHard
A 50 V (rms), 1000 Hz source has an internal impedance Zs = 20 + j6 Ω. The load impedance ZL can be chosen freely. Find the maximum real power Pmax that can be delivered to the load.
Vs = 50 V (rms)f = 1000 HzZs = 20 + j6 Ω
Pmax = W
7.AC impedance & phasorsMedium
A resistor and an inductor are connected in parallel across a 50 V (rms), 50 Hz supply. Find the rms current I.
V = 50 V (rms)f = 50 HzR = 30 ΩL = 20 mH
I = A
8.AC impedance & phasorsHard
A series RLC circuit has R = 2 Ω, L = 5 mH and C = 2.2 µF. Find its bandwidth B (the width of the band between the half-power frequencies), in Hz.
R = 2 ΩL = 5 mHC = 2.2 µF
B = Hz
9.DC motorsMedium
A DC motor (k = 0.2 N·m/A, Ra = 1.5 Ω) runs from 24 V and drives a load torque of 0.4 N·m. Find its speed n in rpm.
V = 24 Vk = 0.2 N·m/ARa = 1.5 ΩT = 0.4 N·m
n = rpm
10.DC motorsHard
A separately excited DC motor on 220 V (Ra = 1.2 Ω) runs at 1800 rpm with an armature current of 10 A. The load changes and the current becomes 5 A, with the field unchanged. Find the new speed n2.
V = 220 VRa = 1.2 Ωn1 = 1800 rpmIa1 = 10 AIa2 = 5 A
n2 = rpm
3Solutions
1.Three-phase power
Answer: P = 9.6 kW
Balanced three-phase systems: in a Y (star) connection the line-to-line voltage is √3 times the phase voltage, VL = √3·Vph, and the line current equals the phase current. In a Δ (delta) connection the line-to-line voltage equals the phase voltage and the line current is √3 times the phase current, IL = √3·Iph. The total power is three times the power of one phase: P = 3·Vph·Iph·cos φ = √3·VL·IL·cos φ.
Phase voltage
Vph = VL = 400 V
Phase current
|Z| = √(18² + 24²) = 30 Ω
Iph = 400/30 = 13.33 A
Total real power
Only the resistive part of each impedance absorbs real power.
P = 3·Iph²·R = 3·13.33²·18 = 9.6 kW
Answer
P = 9.6 kW
Check: cos φ = R/|Z| = 0.6, and √3·VL·IL·cos φ gives the same power.
2.Three-phase power
Answer: Cph = 46.95 µF
Balanced three-phase systems: in a Y (star) connection the line-to-line voltage is √3 times the phase voltage, VL = √3·Vph, and the line current equals the phase current. In a Δ (delta) connection the line-to-line voltage equals the phase voltage and the line current is √3 times the phase current, IL = √3·Iph. The total power is three times the power of one phase: P = 3·Vph·Iph·cos φ = √3·VL·IL·cos φ. Power factor correction: capacitors supply reactive power locally, QC = P·(tan φ1 − tan φ2). Each of the three capacitors supplies QC/3 = V²·ω·C, where V is the voltage across that capacitor: VL in a Δ bank, VL/√3 in a Y bank.
Reactive power before and after
The real power is unchanged, so each power factor fixes the reactive power: Q = P·tan φ.
Q1 = 50·tan(acos 0.8) = 50·0.75 = 37.5 kvar
Q2 = 50·tan(acos 0.95) = 50·0.3287 = 16.43 kvar
Reactive power from the capacitors
QC = Q1 − Q2 = 21.07 kvar
Capacitance per phase
In a Δ bank each capacitor is connected between two lines.
Ideal transformer: the voltages are in the ratio of the turns and the currents in the inverse ratio: V₁/V₂ = N₁/N₂ = a and I₁/I₂ = N₂/N₁ = 1/a, so the power in equals the power out, V₁·I₁ = V₂·I₂. A load impedance Z on the secondary looks like a²·Z from the primary.
Secondary voltage and current
V2 = 480/4 = 120 V
I2 = 120/30 = 4 A
Primary current
An ideal transformer has no losses: V₁·I₁ = V₂·I₂.
I1 = I2/4 = 1 A
Answer
I1 = 1 A
Check: the load seen from the primary is a²·RL = 480 Ω, and 480/480 gives the same current.
4.Transformers
Answer: Sη,max = 40.82 kVA
Transformer losses: the core loss (hysteresis and eddy currents) depends on the voltage and is the same at any load. The copper loss in the windings goes with the current squared, so at a fraction x of rated load it is x²·Pcu,fl. Efficiency η = Pout/(Pout + Pcore + Pcu), with Pout = x·S·pf. The efficiency is highest at the load where the copper loss equals the core loss.
Copper loss equals core loss
x²·225 = 150 → x = √(150/225) = 0.8165
Load at maximum efficiency
Sη,max = x·S = 0.8165·50 = 40.82 kVA
Answer
Sη,max = 40.82 kVA
5.AC power & power factor
Answer: R = 8.348 Ω
AC power: apparent power S = V·I (VA) splits into real power P = S·cos φ (W), which does useful work, and reactive power Q = S·sin φ (var), which moves back and forth between source and load. The power factor is cos φ. A capacitor in parallel supplies reactive power locally, so the line current drops for the same real power.
Resistance from the real power
R = P/I² = 1104/11.5² = 8.348 Ω
Answer
R = 8.348 Ω
6.AC power & power factor
Answer: Pmax = 31.25 W
AC power: apparent power S = V·I (VA) splits into real power P = S·cos φ (W), which does useful work, and reactive power Q = S·sin φ (var), which moves back and forth between source and load. The power factor is cos φ. A capacitor in parallel supplies reactive power locally, so the line current drops for the same real power.
Conjugate match
The load reactance cancels the source reactance, and the load resistance equals the source resistance.
ZL = Zs* = 20 − j6 Ω
Maximum power
I = Vs/(2Rs) = 50/40 = 1.25 A
Pmax = I²·RL = Vs²/(4Rs) = 50²/(4·20) = 31.25 W
Answer
Pmax = 31.25 W
7.AC impedance & phasors
Answer: I = 8.13 A
AC circuits with phasors: resistors, inductors and capacitors have impedances R, jωL and 1/(jωC), with ω = 2πf. In series, impedances add like resistances, but as complex numbers. Rms current and voltage follow Ohm’s law with |Z|.
Reactance
XL = ωL = 2π·50·0.02 = 6.283 Ω
Branch currents
Both branches are connected straight across the supply, so each sees the full voltage V.
IR = V/R = 50/30 = 1.667 A
IX = V/XL = 50/6.283 = 7.958 A
Total current
The resistor current is in phase with V and the reactive current is 90° out of phase, so they add like the sides of a right triangle.
I = √(IR² + IX²) = √(1.667² + 7.958²) = 8.13 A
Answer
I = 8.13 A
8.AC impedance & phasors
Answer: B = 63.66 Hz
AC circuits with phasors: resistors, inductors and capacitors have impedances R, jωL and 1/(jωC), with ω = 2πf. In series, impedances add like resistances, but as complex numbers. Rms current and voltage follow Ohm’s law with |Z|.
Resonant frequency
f0 = 1/(2π·√(0.005·2.2·10⁻⁶)) = 1517 Hz
Quality factor
Q compares the reactance at resonance with the resistance: Q = ω₀L/R.
DC motor: the armature is a resistance Ra in series with the back-EMF E, so V = E + Ia·Ra. The back-EMF grows with speed, E = k·ω, and the torque with current, T = k·Ia, with the same motor constant k (V·s/rad = N·m/A) in SI units. Convert speeds with ω = 2π·n/60. The developed power is E·Ia = T·ω; the input power is V·Ia, and the copper loss Ia²Ra and the rotational loss make the difference. The speed falls in a straight line with torque, ω = V/k − Ra·T/k², from the no-load speed V/k to zero at the stall torque k·V/Ra. At standstill E = 0, so the starting current V/Ra is large unless a resistor limits it.
Armature current
Ia = T/k = 0.4/0.2 = 2 A
Back-EMF and speed
E = 24 − 2·1.5 = 21 V
ω = E/k = 105 rad/s → n = 1003 rpm
Answer
n = 1003 rpm
10.DC motors
Answer: n2 = 1852 rpm
DC motor: the armature is a resistance Ra in series with the back-EMF E, so V = E + Ia·Ra. The back-EMF grows with speed, E = k·ω, and the torque with current, T = k·Ia, with the same motor constant k (V·s/rad = N·m/A) in SI units. Convert speeds with ω = 2π·n/60. The developed power is E·Ia = T·ω; the input power is V·Ia, and the copper loss Ia²Ra and the rotational loss make the difference. The speed falls in a straight line with torque, ω = V/k − Ra·T/k², from the no-load speed V/k to zero at the stall torque k·V/Ra. At standstill E = 0, so the starting current V/Ra is large unless a resistor limits it.