Power Systems and Electrical Machines: cram pack

Formula sheets, the key method steps for every topic and 10 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Three-phase power

Y connection
VL = √3·Vph, IL = Iph
Δ connection
VL = Vph, IL = √3·Iph
Total real power
P = √3·VL·IL·cos φ = 3·Iph²·R
Apparent and reactive power
S = √3·VL·IL, Q = P·tan φ
Correction capacitors
QC = P(tan φ1 − tan φ2), C = QC/(3ωV²)
Voltage across each capacitor
Δ: VL Y: VL/√3
Motor input
Pin = Pout/η

Transformers

Turns ratio
a = N1/N2 = V1/V2
Current ratio
I1/I2 = N2/N1 = 1/a
Rated current
I = S/V
Referred impedance
Z1′ = a²·ZL
Copper loss at part load
Pcu = x²·Pcu,fl
Efficiency
η = x·S·pf/(x·S·pf + Pcore + x²·Pcu,fl)
Maximum efficiency
x = √(Pcore/Pcu,fl)

AC power & power factor

Real power
P = V·I·cos φ
Reactive power
Q = V·I·sin φ
Apparent power
S = V·I = √(P² + Q²)
Power factor
pf = cos φ = P/S
Correction capacitor
QC = P(tan φ1 − tan φ2), C = QC/(ωV²)

AC impedance & phasors

Impedances
ZR = R, ZL = jωL, ZC = 1/(jωC)
Angular frequency
ω = 2πf
Magnitude and angle
|Z| = √(R² + X²), φ = atan(X/R)
Phasor Ohm’s law
V = I·Z

Method

  1. Convert the frequency: ω = 2πf.
  2. Find each reactance: XL = ωL and XC = 1/(ωC).
  3. Add impedances like resistors, with Z = R + jX.
  4. Find the magnitude |Z| = √(R² + X²) and the angle φ = atan(X/R), then use Ohm’s law with phasors.

DC motors

Armature circuit
V = E + IaRa
Back-EMF and torque
E = k·ω, T = k·Ia
Speed
ω = 2π·n/60, ω = (V − IaRa)/k
No-load speed and stall torque
ω0 = V/k, Tstall = k·V/Ra
Powers
Pin = V·Ia, Pdev = E·Ia = T·ω, Pout = Pdev − Prot
Starting
Istart = V/(Ra + Rst)
Speed regulation
SR = (n0 − nFL)/nFL
Maximum developed power
Pmax = V²/(4Ra)
Chopper drive
Va = D·Vdc

Method

  1. Draw the armature circuit: supply V, resistance Ra and the back-EMF E in series.
  2. Use V = E + Ia·Ra to link voltage, current and back-EMF.
  3. Use E = k·ω for speed and T = k·Ia for torque, with ω = 2π·n/60.
  4. For power and efficiency, start from V·Ia, subtract the copper loss Ia²·Ra and then the rotational losses.

2Practice problems

1.Three-phase powerMedium
ABCVL​ = 690 VIL​ = ?M22 kW, η = 91%cos φ = 0.8

A three-phase induction motor delivers 22 kW of mechanical output power at full load. At this load its efficiency is 91% and its power factor is 0.8 lagging. The supply has a line-to-line voltage of 690 V. Find the line current IL.

Pout = 22 kWη = 91%cos φ = 0.8VL = 690 V
IL = A
2.Three-phase powerHard
P = 250 kWφ1​S1​Q2​QC​

A balanced three-phase load takes 250 kW at a power factor of 0.7 lagging from a 415 V (line-to-line), 50 Hz supply. A three-phase capacitor bank in parallel with the load must raise the overall power factor to 0.9 lagging. The real power stays the same. The capacitors are connected in Δ. Find the capacitance Cph of each capacitor in µF.

P = 250 kWpf1 = 0.7pf2 = 0.9VL = 415 Vf = 50 Hz
Cph = µF
3.TransformersMedium
2 ΩN1​N2​50 Ω

An amplifier with an output resistance of 50 Ω drives a 2 Ω loudspeaker through an ideal transformer. For maximum power transfer the loudspeaker must look like 50 Ω from the amplifier. Find the turns ratio a = N₁/N₂.

Rs = 50 ΩRL = 2 Ω
a =
4.TransformersHard
pf 0.95200 kVA, η = 97%

A single-phase 200 kVA transformer has a core loss of 1200 W. At rated load and a power factor of 0.95 lagging its efficiency is 97%. Find the full-load copper loss Pcu,fl in watts.

S = 200 kVAPcore = 1200 Wpf = 0.95η = 97%
Pcu,fl = W
5.AC power & power factorMedium
P = 28 kWQSφ

A single-phase motor takes 28 kW at a power factor of 0.8 lagging from a 400 V supply. Find the line current I.

P = 28 kWpf = 0.8V = 400 V
I = A
6.AC power & power factorHard
12 V50 HzRs​ = 5 ΩXs​ = j10 ΩZL​ = ?

A 12 V (rms), 50 Hz source has an internal impedance Zs = 5 + j10 Ω. The load impedance ZL can be chosen freely. The load for maximum power is built from a resistor in series with a capacitor. Find the capacitance C.

Vs = 12 V (rms)f = 50 HzZs = 5 + j10 Ω
C = µF
7.AC impedance & phasorsMedium
Vf0​ = 200 HzRL = ?C = 47 µF

A series RLC circuit with C = 47 µF must resonate at 200 Hz. Find the inductance L needed.

f0 = 200 HzC = 47 µF
L = mH
8.AC impedance & phasorsHard
230 V200 HzR = 100 ΩL = 20 mHC = 1 µF+−VC​

A series RLC circuit is connected to a 230 V (rms), 200 Hz supply. Find the rms voltage VC across the capacitor.

V = 230 V (rms)f = 200 HzR = 100 ΩL = 20 mHC = 1 µF
VC = V
9.DC motorsMedium
T (N·m)n (rpm)n0​ = ?

A DC motor with k = 0.2 V·s/rad runs from 24 V. Neglecting all losses at no load, find its no-load speed n0 in rpm.

V = 24 Vk = 0.2 V·s/rad
n0 = rpm
10.DC motorsHard
+−220 VD = ?Ra​ = 1.2 ΩM+−En = 400 rpmT = 6 N·m

A DC chopper feeds a motor (k = 1.2 V·s/rad, Ra = 1.2 Ω) from a 220 V DC bus. The average armature voltage is D·220 V. Find the duty cycle D that runs the motor at 400 rpm with a load of 6 N·m.

Vdc = 220 Vk = 1.2 V·s/radRa = 1.2 ΩT = 6 N·mn = 400 rpm
D = %

3Solutions

1.Three-phase power

Answer: IL = 25.29 A

Balanced three-phase systems: in a Y (star) connection the line-to-line voltage is √3 times the phase voltage, VL = √3·Vph, and the line current equals the phase current. In a Δ (delta) connection the line-to-line voltage equals the phase voltage and the line current is √3 times the phase current, IL = √3·Iph. The total power is three times the power of one phase: P = 3·Vph·Iph·cos φ = √3·VL·IL·cos φ.

Electrical input power

Pin = Pout/η = 22/0.91 = 24.18 kW

Line current

IL = Pin/(√3·VL·cos φ) = 24176/(√3·690·0.8) = 25.29 A

Answer

IL = 25.29 A
2.Three-phase power

Answer: Cph = 825.4 µF

Balanced three-phase systems: in a Y (star) connection the line-to-line voltage is √3 times the phase voltage, VL = √3·Vph, and the line current equals the phase current. In a Δ (delta) connection the line-to-line voltage equals the phase voltage and the line current is √3 times the phase current, IL = √3·Iph. The total power is three times the power of one phase: P = 3·Vph·Iph·cos φ = √3·VL·IL·cos φ. Power factor correction: capacitors supply reactive power locally, QC = P·(tan φ1 − tan φ2). Each of the three capacitors supplies QC/3 = V²·ω·C, where V is the voltage across that capacitor: VL in a Δ bank, VL/√3 in a Y bank.

Reactive power before and after

The real power is unchanged, so each power factor fixes the reactive power: Q = P·tan φ.

Q1 = 250·tan(acos 0.7) = 250·1.02 = 255.1 kvar
Q2 = 250·tan(acos 0.9) = 250·0.4843 = 121.1 kvar

Reactive power from the capacitors

QC = Q1 − Q2 = 134 kvar

Capacitance per phase

In a Δ bank each capacitor is connected between two lines.

V = 415 V, ω = 2π·50 = 314.2 rad/s
Cph = (QC/3)/(ω·V²) = 44657/(314.2·415²) = 825.4 µF

Answer

Cph = 825.4 µF
3.Transformers

Answer: a = 5

Ideal transformer: the voltages are in the ratio of the turns and the currents in the inverse ratio: V₁/V₂ = N₁/N₂ = a and I₁/I₂ = N₂/N₁ = 1/a, so the power in equals the power out, V₁·I₁ = V₂·I₂. A load impedance Z on the secondary looks like a²·Z from the primary.

Match the referred load

a²·2 = 50
a = √(50/2) = √25 = 5

Answer

a = 5
4.Transformers

Answer: Pcu,fl = 4676 W

Transformer losses: the core loss (hysteresis and eddy currents) depends on the voltage and is the same at any load. The copper loss in the windings goes with the current squared, so at a fraction x of rated load it is x²·Pcu,fl. Efficiency η = Pout/(Pout + Pcore + Pcu), with Pout = x·S·pf. The efficiency is highest at the load where the copper loss equals the core loss.

Output and input power

Pout = 200·0.95 = 190 kW
Pin = 190000/0.97 = 195876 W

Total and copper losses

Ploss = 195876 − 190000 = 5876 W
Pcu,fl = 5876 − 1200 = 4676 W

Answer

Pcu,fl = 4676 W
5.AC power & power factor

Answer: I = 87.5 A

AC power: apparent power S = V·I (VA) splits into real power P = S·cos φ (W), which does useful work, and reactive power Q = S·sin φ (var), which moves back and forth between source and load. The power factor is cos φ. A capacitor in parallel supplies reactive power locally, so the line current drops for the same real power.

Line current

Only the real part of the power does work, so divide by the power factor.

I = P/(V·cos φ) = 28000/(400·0.8) = 87.5 A

Answer

I = 87.5 A
6.AC power & power factor

Answer: C = 318.3 µF

AC power: apparent power S = V·I (VA) splits into real power P = S·cos φ (W), which does useful work, and reactive power Q = S·sin φ (var), which moves back and forth between source and load. The power factor is cos φ. A capacitor in parallel supplies reactive power locally, so the line current drops for the same real power.

Conjugate match

The load reactance cancels the source reactance, and the load resistance equals the source resistance.

ZL = Zs* = 5 − j10 Ω

Capacitance

XC = 10 Ω → C = 1/(2π·50·10) = 318.3 µF

Answer

C = 318.3 µF
7.AC impedance & phasors

Answer: L = 13.47 mH

AC circuits with phasors: resistors, inductors and capacitors have impedances R, jωL and 1/(jωC), with ω = 2πf. In series, impedances add like resistances, but as complex numbers. Rms current and voltage follow Ohm’s law with |Z|.

Resonance condition

At resonance the inductive and capacitive reactances cancel: ωL = 1/(ωC).

ω₀ = 2π·200 = 1257 rad/s
L = 1/(ω₀²·C) = 1/(1257²·47·10⁻⁶) = 13.47 mH

Answer

L = 13.47 mH
8.AC impedance & phasors

Answer: VC = 235.5 V

AC circuits with phasors: resistors, inductors and capacitors have impedances R, jωL and 1/(jωC), with ω = 2πf. In series, impedances add like resistances, but as complex numbers. Rms current and voltage follow Ohm’s law with |Z|.

Reactances

ω = 2πf = 2π·200 = 1257 rad/s
XL = ωL = 1257·0.02 = 25.13 Ω
XC = 1/(ωC) = 1/(1257·1·10⁻⁶) = 795.8 Ω

Impedance

In series the impedances add as complex numbers: Z = R + j(XL − XC).

|Z| = √(R² + (XL − XC)²) = √(100² + (−770.6)²) = 777.1 Ω

Current

The same current flows through every element of a series circuit.

I = V/|Z| = 230/777.1 = 0.296 A

Voltage across the capacitor

VC = I·XC = 0.296·795.8 = 235.5 V

Answer

VC = 235.5 V
9.DC motors

Answer: n0 = 1146 rpm

DC motor: the armature is a resistance Ra in series with the back-EMF E, so V = E + Ia·Ra. The back-EMF grows with speed, E = k·ω, and the torque with current, T = k·Ia, with the same motor constant k (V·s/rad = N·m/A) in SI units. Convert speeds with ω = 2π·n/60. The developed power is E·Ia = T·ω; the input power is V·Ia, and the copper loss Ia²Ra and the rotational loss make the difference. The speed falls in a straight line with torque, ω = V/k − Ra·T/k², from the no-load speed V/k to zero at the stall torque k·V/Ra. At standstill E = 0, so the starting current V/Ra is large unless a resistor limits it.

No-load speed

ω₀ = V/k = 24/0.2 = 120 rad/s
n0 = 60·120/(2π) = 1146 rpm

Answer

n0 = 1146 rpm
10.DC motors

Answer: D = 25.58 %

DC motor: the armature is a resistance Ra in series with the back-EMF E, so V = E + Ia·Ra. The back-EMF grows with speed, E = k·ω, and the torque with current, T = k·Ia, with the same motor constant k (V·s/rad = N·m/A) in SI units. Convert speeds with ω = 2π·n/60. The developed power is E·Ia = T·ω; the input power is V·Ia, and the copper loss Ia²Ra and the rotational loss make the difference. The speed falls in a straight line with torque, ω = V/k − Ra·T/k², from the no-load speed V/k to zero at the stall torque k·V/Ra. At standstill E = 0, so the starting current V/Ra is large unless a resistor limits it.

Required armature voltage

Va = 1.2·41.89 + 5·1.2 = 56.27 V

Duty cycle

D = 56.27/220 = 25.58 %

Answer

D = 25.58 %

ExamProblems · examproblems.com/courses/power-systems