Power Systems and Electrical Machines: cram pack

Formula sheets, the key method steps for every topic and 10 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Three-phase power

Y connection
VL = √3·Vph, IL = Iph
Δ connection
VL = Vph, IL = √3·Iph
Total real power
P = √3·VL·IL·cos φ = 3·Iph²·R
Apparent and reactive power
S = √3·VL·IL, Q = P·tan φ
Correction capacitors
QC = P(tan φ1 − tan φ2), C = QC/(3ωV²)
Voltage across each capacitor
Δ: VL Y: VL/√3
Motor input
Pin = Pout/η

Transformers

Turns ratio
a = N1/N2 = V1/V2
Current ratio
I1/I2 = N2/N1 = 1/a
Rated current
I = S/V
Referred impedance
Z1′ = a²·ZL
Copper loss at part load
Pcu = x²·Pcu,fl
Efficiency
η = x·S·pf/(x·S·pf + Pcore + x²·Pcu,fl)
Maximum efficiency
x = √(Pcore/Pcu,fl)

AC power & power factor

Real power
P = V·I·cos φ
Reactive power
Q = V·I·sin φ
Apparent power
S = V·I = √(P² + Q²)
Power factor
pf = cos φ = P/S
Correction capacitor
QC = P(tan φ1 − tan φ2), C = QC/(ωV²)

AC impedance & phasors

Impedances
ZR = R, ZL = jωL, ZC = 1/(jωC)
Angular frequency
ω = 2πf
Magnitude and angle
|Z| = √(R² + X²), φ = atan(X/R)
Phasor Ohm’s law
V = I·Z

Method

  1. Convert the frequency: ω = 2πf.
  2. Find each reactance: XL = ωL and XC = 1/(ωC).
  3. Add impedances like resistors, with Z = R + jX.
  4. Find the magnitude |Z| = √(R² + X²) and the angle φ = atan(X/R), then use Ohm’s law with phasors.

DC motors

Armature circuit
V = E + IaRa
Back-EMF and torque
E = k·ω, T = k·Ia
Speed
ω = 2π·n/60, ω = (V − IaRa)/k
No-load speed and stall torque
ω0 = V/k, Tstall = k·V/Ra
Powers
Pin = V·Ia, Pdev = E·Ia = T·ω, Pout = Pdev − Prot
Starting
Istart = V/(Ra + Rst)
Speed regulation
SR = (n0 − nFL)/nFL
Maximum developed power
Pmax = V²/(4Ra)
Chopper drive
Va = D·Vdc

Method

  1. Draw the armature circuit: supply V, resistance Ra and the back-EMF E in series.
  2. Use V = E + Ia·Ra to link voltage, current and back-EMF.
  3. Use E = k·ω for speed and T = k·Ia for torque, with ω = 2π·n/60.
  4. For power and efficiency, start from V·Ia, subtract the copper loss Ia²·Ra and then the rotational losses.

2Practice problems

1.Three-phase powerMedium
ABCVL​ = 208 VNZ = 15 + j20 Ωper phase

A balanced Y-connected load with an impedance of 15 + j20 Ω per phase is connected to a balanced three-phase supply with a line-to-line voltage of 208 V. Find the total real power P absorbed by the load in kW.

VL = 208 VZ = 15 + j20 Ω per phase
P = kW
2.Three-phase powerHard
P = 75 kWφ1​S1​Q2​QC​

A balanced three-phase load takes 75 kW at a power factor of 0.72 lagging from a 400 V (line-to-line), 50 Hz supply. A three-phase capacitor bank in parallel with the load must raise the overall power factor to 0.92 lagging. The real power stays the same. The capacitors are connected in Y. Find the capacitance Cph of each capacitor in µF.

P = 75 kWpf1 = 0.72pf2 = 0.92VL = 400 Vf = 50 Hz
Cph = µF
3.TransformersMedium
RL​ = 30 Ω1012400 VV2​I1​ = ?I2​

An ideal transformer with a turns ratio N₁:N₂ = 10:1 has 2400 V applied to its primary winding. A 30 Ω resistor is connected across the secondary winding. Find the primary current I1.

N1:N2 = 10:1V1 = 2400 VRL = 30 Ω
I1 = A
4.TransformersHard
pf 0.9550 kVA, η = 96.5%

A single-phase 50 kVA transformer has a core loss of 200 W. At rated load and a power factor of 0.95 lagging its efficiency is 96.5%. Find the full-load copper loss Pcu,fl in watts.

S = 50 kVAPcore = 200 Wpf = 0.95η = 96.5%
Pcu,fl = W
5.AC power & power factorMedium
P = 32 kWQSφ

A single-phase motor takes 32 kW at a power factor of 0.9 lagging from a 230 V supply. Find the line current I.

P = 32 kWpf = 0.9V = 230 V
I = A
6.AC power & power factorHard
P1​ = 29 kWQ1​S1​φ

A 50 kVA single-phase transformer supplies a load of 29 kW at a power factor of 0.75 lagging. How much extra real power ΔP can be added as a resistive (unity power factor) load before the transformer reaches its kVA rating?

Smax = 50 kVAP1 = 29 kWpf1 = 0.75
ΔP = kW
7.AC impedance & phasorsMedium
50 V1000 HzR = 10 ΩL = 50 mHC = 1 µF

A series RLC circuit is connected to a 50 V (rms), 1000 Hz supply. Find the phase angle φ of the impedance, in degrees (positive when the current lags the voltage).

V = 50 V (rms)f = 1000 HzR = 10 ΩL = 50 mHC = 1 µF
φ = °
8.AC impedance & phasorsHard
10 Vf0​R = 50 ΩL = 50 mHC = 0.22 µF

A series RLC circuit is driven by a 10 V (rms) source whose frequency is set to the resonant frequency of the circuit. Find the rms voltage VL across the inductor.

V = 10 V (rms)R = 50 ΩL = 50 mHC = 0.22 µF
VL = V
9.DC motorsMedium
T (N·m)n (rpm)0.8 N·mn0​nFL​

A DC motor (k = 0.2 V·s/rad, Ra = 0.8 Ω) runs from 24 V. At full load it draws 4 A. Neglecting the no-load current, find its speed regulation SR = (n₀ − nFL)/nFL in percent.

V = 24 Vk = 0.2 V·s/radRa = 0.8 ΩIFL = 4 A
SR = %
10.DC motorsHard
+−48 VD = ?Ra​ = 2 ΩM+−En = 1000 rpmT = 0.24 N·m

A DC chopper feeds a motor (k = 0.12 V·s/rad, Ra = 2 Ω) from a 48 V DC bus. The average armature voltage is D·48 V. Find the duty cycle D that runs the motor at 1000 rpm with a load of 0.24 N·m.

Vdc = 48 Vk = 0.12 V·s/radRa = 2 ΩT = 0.24 N·mn = 1000 rpm
D = %

3Solutions

1.Three-phase power

Answer: P = 1.038 kW

Balanced three-phase systems: in a Y (star) connection the line-to-line voltage is √3 times the phase voltage, VL = √3·Vph, and the line current equals the phase current. In a Δ (delta) connection the line-to-line voltage equals the phase voltage and the line current is √3 times the phase current, IL = √3·Iph. The total power is three times the power of one phase: P = 3·Vph·Iph·cos φ = √3·VL·IL·cos φ.

Phase voltage

Vph = 208/√3 = 120.1 V

Phase current

|Z| = √(15² + 20²) = 25 Ω
Iph = 120.1/25 = 4.804 A

Total real power

Only the resistive part of each impedance absorbs real power.

P = 3·Iph²·R = 3·4.804²·15 = 1.038 kW

Answer

P = 1.038 kW

Check: cos φ = R/|Z| = 0.6, and √3·VL·IL·cos φ gives the same power.

2.Three-phase power

Answer: Cph = 802.5 µF

Balanced three-phase systems: in a Y (star) connection the line-to-line voltage is √3 times the phase voltage, VL = √3·Vph, and the line current equals the phase current. In a Δ (delta) connection the line-to-line voltage equals the phase voltage and the line current is √3 times the phase current, IL = √3·Iph. The total power is three times the power of one phase: P = 3·Vph·Iph·cos φ = √3·VL·IL·cos φ. Power factor correction: capacitors supply reactive power locally, QC = P·(tan φ1 − tan φ2). Each of the three capacitors supplies QC/3 = V²·ω·C, where V is the voltage across that capacitor: VL in a Δ bank, VL/√3 in a Y bank.

Reactive power before and after

The real power is unchanged, so each power factor fixes the reactive power: Q = P·tan φ.

Q1 = 75·tan(acos 0.72) = 75·0.9639 = 72.29 kvar
Q2 = 75·tan(acos 0.92) = 75·0.426 = 31.95 kvar

Reactive power from the capacitors

QC = Q1 − Q2 = 40.34 kvar

Capacitance per phase

In a Y bank each capacitor is connected between a line and the star point.

V = 400/√3 = 230.9 V, ω = 2π·50 = 314.2 rad/s
Cph = (QC/3)/(ω·V²) = 13446/(314.2·230.9²) = 802.5 µF

Answer

Cph = 802.5 µF
3.Transformers

Answer: I1 = 0.8 A

Ideal transformer: the voltages are in the ratio of the turns and the currents in the inverse ratio: V₁/V₂ = N₁/N₂ = a and I₁/I₂ = N₂/N₁ = 1/a, so the power in equals the power out, V₁·I₁ = V₂·I₂. A load impedance Z on the secondary looks like a²·Z from the primary.

Secondary voltage and current

V2 = 2400/10 = 240 V
I2 = 240/30 = 8 A

Primary current

An ideal transformer has no losses: V₁·I₁ = V₂·I₂.

I1 = I2/10 = 0.8 A

Answer

I1 = 0.8 A

Check: the load seen from the primary is a²·RL = 3000 Ω, and 2400/3000 gives the same current.

4.Transformers

Answer: Pcu,fl = 1523 W

Transformer losses: the core loss (hysteresis and eddy currents) depends on the voltage and is the same at any load. The copper loss in the windings goes with the current squared, so at a fraction x of rated load it is x²·Pcu,fl. Efficiency η = Pout/(Pout + Pcore + Pcu), with Pout = x·S·pf. The efficiency is highest at the load where the copper loss equals the core loss.

Output and input power

Pout = 50·0.95 = 47.5 kW
Pin = 47500/0.965 = 49223 W

Total and copper losses

Ploss = 49223 − 47500 = 1723 W
Pcu,fl = 1723 − 200 = 1523 W

Answer

Pcu,fl = 1523 W
5.AC power & power factor

Answer: I = 154.6 A

AC power: apparent power S = V·I (VA) splits into real power P = S·cos φ (W), which does useful work, and reactive power Q = S·sin φ (var), which moves back and forth between source and load. The power factor is cos φ. A capacitor in parallel supplies reactive power locally, so the line current drops for the same real power.

Line current

Only the real part of the power does work, so divide by the power factor.

I = P/(V·cos φ) = 32000/(230·0.9) = 154.6 A

Answer

I = 154.6 A
6.AC power & power factor

Answer: ΔP = 13.96 kW

AC power: apparent power S = V·I (VA) splits into real power P = S·cos φ (W), which does useful work, and reactive power Q = S·sin φ (var), which moves back and forth between source and load. The power factor is cos φ. A capacitor in parallel supplies reactive power locally, so the line current drops for the same real power.

Reactive power of the existing load

Q1 = 29·tan(arccos 0.75) = 25.58 kvar

Largest total real power

At full rating S = Smax, and Q is unchanged by the resistive load.

P = √(Smax² − Q1²) = √(50² − 25.58²) = 42.96 kW

Extra real power

ΔP = 42.96 − 29 = 13.96 kW

Answer

ΔP = 13.96 kW
7.AC impedance & phasors

Answer: φ = 86.31 °

AC circuits with phasors: resistors, inductors and capacitors have impedances R, jωL and 1/(jωC), with ω = 2πf. In series, impedances add like resistances, but as complex numbers. Rms current and voltage follow Ohm’s law with |Z|.

Reactances

ω = 2πf = 2π·1000 = 6283 rad/s
XL = ωL = 6283·0.05 = 314.2 Ω
XC = 1/(ωC) = 1/(6283·1·10⁻⁶) = 159.2 Ω

Impedance

In series the impedances add as complex numbers: Z = R + j(XL − XC).

|Z| = √(R² + (XL − XC)²) = √(10² + (155)²) = 155.3 Ω

Phase angle

φ = arctan((XL − XC)/R) = arctan(155/10) = 86.31°

Answer

φ = 86.31°
8.AC impedance & phasors

Answer: VL = 95.35 V

AC circuits with phasors: resistors, inductors and capacitors have impedances R, jωL and 1/(jωC), with ω = 2πf. In series, impedances add like resistances, but as complex numbers. Rms current and voltage follow Ohm’s law with |Z|.

Resonance

At resonance the reactances cancel, so the impedance is just R.

ω₀ = 1/√(LC) = 1/√(0.05·0.22·10⁻⁶) = 9535 rad/s
I = V/R = 10/50 = 0.2 A

Voltage across the inductor

XL = ω₀L = 9535·0.05 = 476.7 Ω
VL = I·XL = 0.2·476.7 = 95.35 V

Answer

VL = 95.35 V

This is Q = 9.535 times the supply voltage.

9.DC motors

Answer: SR = 15.38 %

DC motor: the armature is a resistance Ra in series with the back-EMF E, so V = E + Ia·Ra. The back-EMF grows with speed, E = k·ω, and the torque with current, T = k·Ia, with the same motor constant k (V·s/rad = N·m/A) in SI units. Convert speeds with ω = 2π·n/60. The developed power is E·Ia = T·ω; the input power is V·Ia, and the copper loss Ia²Ra and the rotational loss make the difference. The speed falls in a straight line with torque, ω = V/k − Ra·T/k², from the no-load speed V/k to zero at the stall torque k·V/Ra. At standstill E = 0, so the starting current V/Ra is large unless a resistor limits it.

No-load and full-load speed

n₀ = 60·24/(2π·0.2) = 1146 rpm
nFL = 60·(24 − 4·0.8)/(2π·0.2) = 993.1 rpm

Speed regulation

SR = (1146 − 993.1)/993.1·100 = 15.38 %

Answer

SR = 15.38 %
10.DC motors

Answer: D = 34.51 %

DC motor: the armature is a resistance Ra in series with the back-EMF E, so V = E + Ia·Ra. The back-EMF grows with speed, E = k·ω, and the torque with current, T = k·Ia, with the same motor constant k (V·s/rad = N·m/A) in SI units. Convert speeds with ω = 2π·n/60. The developed power is E·Ia = T·ω; the input power is V·Ia, and the copper loss Ia²Ra and the rotational loss make the difference. The speed falls in a straight line with torque, ω = V/k − Ra·T/k², from the no-load speed V/k to zero at the stall torque k·V/Ra. At standstill E = 0, so the starting current V/Ra is large unless a resistor limits it.

Required armature voltage

Va = 0.12·104.7 + 2·2 = 16.57 V

Duty cycle

D = 16.57/48 = 34.51 %

Answer

D = 34.51 %

ExamProblems · examproblems.com/courses/power-systems