Statics: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Vectors: dot & cross product

Magnitude
|a| = √(ax² + ay² + az²)
Unit vector
û = a/|a|
Components from an angle
Fx = F·cos θ, Fy = F·sin θ
Dot product
a·b = axbx + ayby + azbz = |a||b|cos θ
Scalar projection of a onto b
a·b/|b|
Work
W = F·d
Cross product
a × b = (aybz − azby, azbx − axbz, axby − aybx)
Areas
parallelogram |a × b|, triangle ½|a × b|
Moment about O
MO = r × F, r = A − O
Volume of a parallelepiped
V = |a·(b × c)|

Method

  1. Write every vector in components; for a force given by a magnitude and an angle, use F·cos θ and F·sin θ.
  2. For lengths and directions use the magnitude √(x² + y² + z²) and the unit vector a/|a|.
  3. Use the dot product for angles, projections, perpendicularity and work: a·b = |a||b|cos θ.
  4. Use the cross product for perpendicular vectors, areas and moments: write the three components carefully, keeping the order a × b.

Beam support reactions

Equilibrium
ΣFx = 0, ΣFy = 0, ΣM = 0
Uniform load
resultant w·L at the middle of the load
Moment
M = F·d

Method

  1. Draw a free-body diagram and replace each support by its reactions.
  2. Replace every distributed load by a single force at its centroid.
  3. Take moments about one support to find the reaction at the other.
  4. Use ΣFy = 0 to find the remaining reaction, and check with a second moment equation.

Truss: method of joints

Method of joints
ΣFx = 0, ΣFy = 0 at each joint
Method of sections
ΣM = 0 about a cut point
Member force
positive = tension, negative = compression

Method

  1. Find the support reactions for the whole truss.
  2. Method of joints: start at a joint with at most two unknown member forces and use ΣFx = 0 and ΣFy = 0.
  3. Method of sections: cut through the member you need and take moments about a point where the other unknown members meet.
  4. Assume tension; a negative answer means compression.

Frames & machines

Equilibrium of each member
ΣFx = 0, ΣFy = 0, ΣM = 0
Two-force member
force along the line through its two pins
Pin force
equal and opposite on the two members it joins
Magnitude of a pin force
F = √(Fx² + Fy²)
Lever, pliers, bell crank
Fin·a = Fout·b
Toggle
Flink = F/(2 sin θ), Q = F/(2 tan θ)
Uniform load
resultant w·L at the middle of the load

Method

  1. Draw the whole structure and find the support reactions if there are no more than three unknowns.
  2. Spot the two-force members: loaded only at two pins, their force acts along the line between the pins.
  3. Take the frame apart and draw every member on its own, with equal and opposite pin forces where members meet.
  4. For each member, take moments about a pin with unknown forces, then use ΣFx = 0 and ΣFy = 0; combine components into a magnitude at the end.

Shear force & bending moment

Shear and moment
V = ΣF on one side, M = ΣF·d on one side
Bending stress
σ = M·y/I
Rectangle
I = bh³/12
Section modulus
W = I/ymax
Simply supported, uniform load
Mmax = wL²/8

Method

  1. Find the support reactions from equilibrium of the whole beam.
  2. Cut the beam at the section you need and keep one side.
  3. Shear force: sum of the vertical forces on that side. Bending moment: sum of their moments about the cut.
  4. For the maximum moment, find where the shear force is zero.

Centroid & second moment of area

Centroid
ȳ = ΣAiyi/ΣAi
Rectangle
I = bh³/12
Parallel-axis theorem
I = Ic + A·d²
Composite section
I = Σ(Ic,i + Aidi²)

2Practice problems

1.Vectors: dot & cross productMedium
xyzab

Find the value of k for which the vectors a = (6, −3, 5) and b = (k, 5, −4) are perpendicular.

a = (6, −3, 5)b = (k, 5, −4)
k =
2.Vectors: dot & cross productHard
xyzabc

Find the volume V of the parallelepiped whose edges from one corner are a = (1, −2, −3), b = (5, 4, 0) and c = (4, −1, 3).

a = (1, −2, −3)b = (5, 4, 0)c = (4, −1, 3)
V =
3.Beam support reactionsMedium
P1​ = 15 kNP2​ = 15 kNABRA​ = ?RB​1.5 m1 m1.5 m

The simply supported beam has a pin at A and a roller at B. Find the vertical support reaction RA.

L = 4 mP1 = 15 kN at 1.5 mP2 = 15 kN at 2.5 m
RA = kN
4.Beam support reactionsHard
w = 12 kN/mP = 20 kNABRA​ = ?RB​2 m1 m1 m

The simply supported beam has a pin at A and a roller at B. Find the vertical support reaction RA.

L = 4 mP = 20 kN at 3 mw = 12 kN/m from 2 to 4 m
RA = kN
5.Truss: method of jointsMedium
ABCDEFGH15 kN20 kN15 kN10 kN15 kN4 × 3 m3 m

Exactly one member of this truss carries no force under these loads. Which is the zero-force member? Click it in the diagram.

B: 15 kN ↓C: 20 kN ↓F: 15 kN ↓G: 10 kN ↓H: 15 kN ↓
  1. 1member AB
  2. 2member BC
  3. 3member CD
  4. 4member DE
  5. 5member FG
  6. 6member GH
  7. 7member AF
  8. 8member HE
  9. 9member BF
  10. 10member CG
  11. 11member DH
  12. 12member FC
  13. 13member HC
6.Truss: method of jointsHard
ABCDEFGH35 kN20 kN40 kN35 kN20 kN35 kN4 × 4 m3 m

Exactly one member of this truss carries no force under these loads. Which is the zero-force member? Click it in the diagram.

B: 35 kN ↓C: 20 kN ↓D: 40 kN ↓F: 35 kN ↓F: 20 kN →H: 35 kN ↓
  1. 1member AB
  2. 2member BC
  3. 3member CD
  4. 4member DE
  5. 5member FG
  6. 6member GH
  7. 7member AF
  8. 8member HE
  9. 9member BF
  10. 10member CG
  11. 11member DH
  12. 12member FC
  13. 13member HC
7.Frames & machinesMedium
12 kN8 m4 m3.6 mABCK

The frame shown has pins at A, B and C; A and C are fixed to the ground 8 m apart, and B is 4 m above the ground and 3.6 m to the right of A. A vertical load of 12 kN acts on member AB at K, 2.16 m (horizontally) from A. Find the force FBC in member BC.

P = 12 kNL = 8 mH = 4 mhorizontal distance A to B = 3.6 mhorizontal distance A to K = 2.16 m
FBC = kN
8.Frames & machinesHard
5 kN2 kN6 m4 m2.7 mABCK

The frame shown has pins at A, B and C; A and C are fixed to the ground 6 m apart, and B is 4 m high and 2.7 m to the right of A. Member AB carries a vertical load of 5 kN at K, 0.675 m (horizontally) from A, and a horizontal load of 2 kN to the right acts at B on member AB. Find the size of the horizontal reaction Ax at A.

P = 5 kNQ = 2 kNL = 6 mH = 4 mhorizontal distance A to B = 2.7 mhorizontal distance A to K = 0.675 m
Ax = kN
9.Shear force & bending momentMedium
35 kN10 kNABCDEFG1 m1 m1 m1 m1 m1 m

The marks A to G split the beam into six equal parts. At which mark is the bending moment largest in size, sagging or hogging? Click it in the diagram.

35 kN @ 4 m10 kN @ 5 m
  1. 1A (x = 0 m)
  2. 2B (x = 1 m)
  3. 3C (x = 2 m)
  4. 4D (x = 3 m)
  5. 5E (x = 4 m)
  6. 6F (x = 5 m)
  7. 7G (x = 6 m)
10.Shear force & bending momentHard
6 kN/m25 kN40 kNABCDEFG1 m1 m1 m1 m1 m1 m

The marks A to G split the beam into six equal parts. At which mark is the bending moment largest in size, sagging or hogging? Click it in the diagram.

25 kN @ 0 m40 kN @ 6 m6 kN/m, 1–4 m
  1. 1A (x = 0 m)
  2. 2B (x = 1 m)
  3. 3C (x = 2 m)
  4. 4D (x = 3 m)
  5. 5E (x = 4 m)
  6. 6F (x = 5 m)
  7. 7G (x = 6 m)
11.Centroid & second moment of areaMedium
xD = 230d = 214dimensions in mm

A circular tube has outside diameter D = 230 mm and inside diameter d = 214 mm. Find its radius of gyration r about the horizontal centroidal axis.

D = 230 mmd = 214 mm
r = mm
12.Centroid & second moment of areaHard
3001024014xM = 20 kN·mdimensions in mm

The T-section is used as a beam with the flange on top and carries a sagging bending moment of 20 kN·m. Find the size of the bending stress σtop at the top edge.

bf = 300 mmtf = 10 mmtw = 14 mmhw = 240 mmM = 20 kN·m
σtop = MPa

3Solutions

1.Vectors: dot & cross product

Answer: k = 5.833

Dot product: a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.

Dot product equals zero

a·b = 6·k + (−3)·5 + 5·(−4) = 0
−35 + 6·k = 0

Solve for k

k = −(−35)/6 = 5.833

Answer

k = 5.833
2.Vectors: dot & cross product

Answer: V = 105

Cross product: a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.

Cross product b × c

(b × c)x = bycz − bzcy = 4·3 − 0·(−1) = 12
(b × c)y = bzcx − bxcz = 0·4 − 5·3 = −15
(b × c)z = bxcy − bycx = 5·(−1) − 4·4 = −21

Dot product with a

a·(b × c) = 1·12 + (−2)·(−15) + (−3)·(−21) = 105
V = |105| = 105

Answer

V = 105
3.Beam support reactions

Answer: RA = 15 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.

P1​ = 15 kNP2​ = 15 kNABRA​RB​1.5 m1 m1.5 m

Free-body diagram

Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.

Equilibrium

Moments about A, counter-clockwise positive. Then vertical force balance.

ΣMA = 0: RB·4 = 15·1.5 + 15·2.5
RB = 60/4 = 15 kN
ΣFy = 0: RA = 30 − 15 = 15 kN

Answer

RA = 15 kN
4.Beam support reactions

Answer: RA = 11 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.

w = 12 kN/mP = 20 kNABRA​RB​2 m1 m1 m

Free-body diagram

Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.

Equilibrium

Moments about A, counter-clockwise positive. Then vertical force balance.

UDL resultant: W = w·ℓ = 12·2 = 24 kN, acting at x̄ = 3 m
ΣMA = 0: RB·4 = 20·3 + 12·2·3
RB = 132/4 = 33 kN
ΣFy = 0: RA = 44 − 33 = 11 kN

Answer

RA = 11 kN
5.Truss: method of joints

Answer: member DH

Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.

Joint D

CD and DE lie on one straight line and the joint carries no load. Balancing forces across that line leaves only DH.

ΣF⊥ = 0 → FDH = 0

Check with the method of joints

Solving all joints gives these member forces (T = tension, C = compression).

AB: 41.25 kN (T), BC: 41.25 kN (T), CD: 33.75 kN (T), DE: 33.75 kN (T), FG: 52.5 kN (C), GH: 52.5 kN (C), AF: 58.34 kN (C), HE: 47.73 kN (C), BF: 15 kN (T), CG: 10 kN (C), DH: 0, FC: 15.91 kN (T), HC: 26.52 kN (T)

Answer

Zero-force member: DH
6.Truss: method of joints

Answer: member CG

Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.

Joint G

FG and GH lie on one straight line and the joint carries no load. Balancing forces across that line leaves only CG.

ΣF⊥ = 0 → FCG = 0

Check with the method of joints

Solving all joints gives these member forces (T = tension, C = compression).

AB: 123.3 kN (T), BC: 123.3 kN (T), CD: 116.7 kN (T), DE: 116.7 kN (T), FG: 133.3 kN (C), GH: 133.3 kN (C), AF: 129.2 kN (C), HE: 145.8 kN (C), BF: 35 kN (T), CG: 0, DH: 40 kN (T), FC: 12.5 kN (T), HC: 20.83 kN (T)

Answer

Zero-force member: CG
7.Frames & machines

Answer: FBC = 4.817 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Two-force member BC

BC = √(4.4² + 4²) = 5.946 m

Whole frame: moments about A

The ground pushes on BC at C along CB; its horizontal component passes through A, only the vertical one has a moment.

FBC·(4/5.946)·8 = 12·2.16
FBC = 4.817 kN (compression)

Answer

FBC = 4.817 kN
8.Frames & machines

Answer: Ax = 0.4359 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Direction of BC

BC = 5.186 m, cos = 0.6364, sin = 0.7714

Whole frame: moments about A

FBC·0.7714·6 = 5·0.675 + 2·4
FBC = 2.458 kN

Horizontal balance

Ax + 2 − 2.458·0.6364 = 0
Ax = −0.4359 kN → |Ax| = 0.4359 kN

Answer

Ax = 0.4359 kN

The minus sign means Ax points to the left.

9.Shear force & bending moment

Answer: E (x = 4 m)

Largest bending moment: M changes slope wherever the shear force changes, so its peaks sit where the shear force crosses zero: under a point load, inside a distributed load, or over a support of an overhang. At a fixed support of a cantilever the moment is largest at the wall. Compare the size of M at those places, sagging or hogging.

Support reactions

Take moments about one support, then use the vertical force balance.

R1 = 13.33 kN, R2 = 31.67 kN

Bending moment at every mark

Sum the moments of all forces on one side of the cut. Sagging is positive, hogging negative.

MA = 0, MB = 13.33, MC = 26.67, MD = 40, ME = 53.33 kN·m, MF = 31.67, MG = 0

Answer

Mark E: ME = 53.33 kN·m
10.Shear force & bending moment

Answer: E (x = 4 m)

Largest bending moment: M changes slope wherever the shear force changes, so its peaks sit where the shear force crosses zero: under a point load, inside a distributed load, or over a support of an overhang. At a fixed support of a cantilever the moment is largest at the wall. Compare the size of M at those places, sagging or hogging.

Support reactions

Take moments about one support, then use the vertical force balance.

R1 = 15.67 kN, R2 = 67.33 kN

Bending moment at every mark

Sum the moments of all forces on one side of the cut. Sagging is positive, hogging negative.

MA = 0, MB = −25, MC = −37.33, MD = −55.67, ME = −80 kN·m, MF = −40, MG = 0

Answer

Mark E: ME = −80 kN·m
11.Centroid & second moment of area

Answer: r = 78.54 mm

Second moment of area: for a rectangle about its own centroidal axis I = bh³/12, and about its base bh³/3 (parallel-axis theorem I = Ic + A·d²). A hole is handled by subtracting its I, as long as both parts share the same axis. The elastic section modulus is S = I/c, where c is the distance to the extreme fibre. The radius of gyration r = √(I/A) is the distance at which the whole area would give the same I; it is used in column buckling.

Net area and second moment of area

A = π(D² − d²)/4 = 5579 mm²
I = π(D⁴ − d⁴)/64 = 3.442 × 10⁷ mm⁴

Radius of gyration

r = √(I/A) = √(3.442 × 10⁷/5579) = 78.54 mm

Answer

r = 78.54 mm
12.Centroid & second moment of area

Answer: σtop = 34.72 MPa

Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.

Split into two rectangles

Measure every y from the bottom edge.

flange: Af = 300·10 = 3000 mm², yf = 240 + 10/2 = 245 mm
web: Aw = 14·240 = 3360 mm², yw = 240/2 = 120 mm

Centroid

ȳ = (Afyf + Awyw)/(Af + Aw) = (3000·245 + 3360·120)/6360 = 179 mm

Parallel-axis theorem

flange: 300·10³/12 + 3000·(245 − 179)² = 1.311 × 10⁷ mm⁴
web: 14·240³/12 + 3360·(120 − 179)² = 2.781 × 10⁷ mm⁴
Ix = 1.311 × 10⁷ + 2.781 × 10⁷ = 4.092 × 10⁷ mm⁴

Bending stress

The top edge is h − ȳ from the axis.

y = 250 − 179 = 71.04 mm
σ = M·y/I = 2 × 10⁷·71.04/4.092 × 10⁷ = 34.72 MPa

Answer

σtop = 34.72 MPa

ExamProblems · examproblems.com/courses/statics