Statics: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Vectors: dot & cross product

Magnitude
|a| = √(ax² + ay² + az²)
Unit vector
û = a/|a|
Components from an angle
Fx = F·cos θ, Fy = F·sin θ
Dot product
a·b = axbx + ayby + azbz = |a||b|cos θ
Scalar projection of a onto b
a·b/|b|
Work
W = F·d
Cross product
a × b = (aybz − azby, azbx − axbz, axby − aybx)
Areas
parallelogram |a × b|, triangle ½|a × b|
Moment about O
MO = r × F, r = A − O
Volume of a parallelepiped
V = |a·(b × c)|

Method

  1. Write every vector in components; for a force given by a magnitude and an angle, use F·cos θ and F·sin θ.
  2. For lengths and directions use the magnitude √(x² + y² + z²) and the unit vector a/|a|.
  3. Use the dot product for angles, projections, perpendicularity and work: a·b = |a||b|cos θ.
  4. Use the cross product for perpendicular vectors, areas and moments: write the three components carefully, keeping the order a × b.

Beam support reactions

Equilibrium
ΣFx = 0, ΣFy = 0, ΣM = 0
Uniform load
resultant w·L at the middle of the load
Moment
M = F·d

Method

  1. Draw a free-body diagram and replace each support by its reactions.
  2. Replace every distributed load by a single force at its centroid.
  3. Take moments about one support to find the reaction at the other.
  4. Use ΣFy = 0 to find the remaining reaction, and check with a second moment equation.

Truss: method of joints

Method of joints
ΣFx = 0, ΣFy = 0 at each joint
Method of sections
ΣM = 0 about a cut point
Member force
positive = tension, negative = compression

Method

  1. Find the support reactions for the whole truss.
  2. Method of joints: start at a joint with at most two unknown member forces and use ΣFx = 0 and ΣFy = 0.
  3. Method of sections: cut through the member you need and take moments about a point where the other unknown members meet.
  4. Assume tension; a negative answer means compression.

Frames & machines

Equilibrium of each member
ΣFx = 0, ΣFy = 0, ΣM = 0
Two-force member
force along the line through its two pins
Pin force
equal and opposite on the two members it joins
Magnitude of a pin force
F = √(Fx² + Fy²)
Lever, pliers, bell crank
Fin·a = Fout·b
Toggle
Flink = F/(2 sin θ), Q = F/(2 tan θ)
Uniform load
resultant w·L at the middle of the load

Method

  1. Draw the whole structure and find the support reactions if there are no more than three unknowns.
  2. Spot the two-force members: loaded only at two pins, their force acts along the line between the pins.
  3. Take the frame apart and draw every member on its own, with equal and opposite pin forces where members meet.
  4. For each member, take moments about a pin with unknown forces, then use ΣFx = 0 and ΣFy = 0; combine components into a magnitude at the end.

Shear force & bending moment

Shear and moment
V = ΣF on one side, M = ΣF·d on one side
Bending stress
σ = M·y/I
Rectangle
I = bh³/12
Section modulus
W = I/ymax
Simply supported, uniform load
Mmax = wL²/8

Method

  1. Find the support reactions from equilibrium of the whole beam.
  2. Cut the beam at the section you need and keep one side.
  3. Shear force: sum of the vertical forces on that side. Bending moment: sum of their moments about the cut.
  4. For the maximum moment, find where the shear force is zero.

Centroid & second moment of area

Centroid
ȳ = ΣAiyi/ΣAi
Rectangle
I = bh³/12
Parallel-axis theorem
I = Ic + A·d²
Composite section
I = Σ(Ic,i + Aidi²)

2Practice problems

1.Vectors: dot & cross productMedium
xyzab

Find the dot product a·b of a = (−7, 1, −7) and b = (−7, −1, 4).

a = (−7, 1, −7)b = (−7, −1, 4)
a·b =
2.Vectors: dot & cross productHard
xyzrFOA

A force F = (10, −30, 10) N acts at point A(−3, 2, −2). Coordinates are in metres. Find the x-component Mx of the moment of the force about the origin O(0, 0, 0).

F = (10, −30, 10) NA(−3, 2, −2) mO(0, 0, 0) m
Mx = N·m
3.Beam support reactionsMedium
P1​ = 70 kNP2​ = 80 kNABCRB​ = ?5 m1 m2 m

The beam has a pin at A and a roller at B, 6 m from A, and overhangs B to the free end C. Find the vertical reaction RB, taking upward as positive.

AB = 6 mAC = 8 mP1 = 70 kN at 5 mP2 = 80 kN at 8 m
RB = kN
4.Beam support reactionsHard
w = 3 kN/mP = 55 kNABCRB​ = ?0.5 m2 m2 m1.5 m

The beam has a pin at A and a roller at B, 4.5 m from A, and overhangs B to the free end C. It carries a point load P at 0.5 m from A and a uniformly distributed load w from 2.5 m to the free end at 6 m. Find the vertical reaction RB, taking upward as positive.

AB = 4.5 mAC = 6 mP = 55 kN at 0.5 mw = 3 kN/m from 2.5 to 6 m
RB = kN
5.Truss: method of jointsMedium
ABCDEFGH40 kN25 kN4 × 4 m3 m

Exactly one member of this truss carries no force under these loads. Which is the zero-force member? Click it in the diagram.

B: 40 kN ↓G: 25 kN ↓
  1. 1member AB
  2. 2member BC
  3. 3member CD
  4. 4member DE
  5. 5member FG
  6. 6member GH
  7. 7member AF
  8. 8member HE
  9. 9member BF
  10. 10member CG
  11. 11member DH
  12. 12member FC
  13. 13member HC
6.Truss: method of jointsHard
ABCDEFGH40 kN10 kN25 kN15 kN4 × 3 m4 m

Exactly one member of this truss carries no force under these loads. Which is the zero-force member? Click it in the diagram.

D: 40 kN ↓F: 10 kN ↓F: 25 kN →G: 15 kN ↓
  1. 1member AB
  2. 2member BC
  3. 3member CD
  4. 4member DE
  5. 5member FG
  6. 6member GH
  7. 7member AF
  8. 8member HE
  9. 9member BF
  10. 10member CG
  11. 11member DH
  12. 12member BG
  13. 13member DG
7.Frames & machinesMedium
OAB300 NQ100 mm80 mmFO​ = ?

The bell crank shown turns about the pin O. A vertical force of 300 N at A (100 mm from O) is balanced by a horizontal force at B (80 mm above O). Find the magnitude of the pin reaction FO.

F = 300 NOA = 100 mmOB = 80 mm
FO = N
8.Frames & machinesHard
15 kN4.8 m1.2 m1.2 mABCDE

The A-frame shown stands on a pin at A and a roller at B, 4.8 m apart. The legs meet at the pin C, 2.4 m high, and are tied by the horizontal bar DE at 1.2 m. A horizontal force of 15 kN to the right acts at C. Find the tension T in the tie.

P = 15 kNAB = 4.8 mheight of C = 2.4 mheight of DE = 1.2 m
T = kN
9.Shear force & bending momentMedium
M0​ = 55 kN·mAB3 m5 m

The simply supported beam carries a clockwise couple M0 = 55 kN·m at x = 3 m from A, and no other load. Find the bending moment Mx just to the right of the couple. Use sagging moments positive and upward shear on the left face positive.

L = 8 mM0 = 55 kN·m clockwise, at 3 m
Mx = kN·m
10.Shear force & bending momentHard
w = 5 kN/mABC6 m1.5 m

The beam rests on a pin at A and a roller at B and overhangs B by 1.5 m to the free end C. A uniformly distributed load w acts over the whole length A–C. Find the distance xc from A to the point of contraflexure between the supports (where the bending moment changes sign).

L = 7.5 mw = 5 kN/m from 0 to 7.5 msupports at x = 0 and x = 6 m
xc = m
11.Centroid & second moment of areaMedium
10070t = 10ȳ = ?dimensions in mm

A channel section lies with its open side up: a base plate 100 mm wide with two upright legs, 70 mm high overall. Base and legs are all 10 mm thick. Find the height ȳ of the centroid above the bottom edge.

b = 100 mmh = 70 mmt = 10 mm
ȳ = mm
12.Centroid & second moment of areaHard
120 mm240 mm144 mm30 × 30xIx​ = ?

A 120 mm × 240 mm plate has a rectangular cut-out 30 mm wide and 30 mm high, centred on the vertical centre line with its centre 144 mm above the bottom. Find the second moment of area Ix about the horizontal axis through the centroid.

b = 120 mmh = 240 mmcut-out: 30 × 30 mmhole centre: y = 144 mm
Ix = × 10⁶ mm⁴

3Solutions

1.Vectors: dot & cross product

Answer: a·b = 20

Dot product: a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.

Multiply matching components and add

a·b = (−7)·(−7) + 1·(−1) + (−7)·4 = 49 + (−1) + (−28) = 20

Answer

a·b = 20

Positive: the angle between the vectors is less than 90°.

2.Vectors: dot & cross product

Answer: Mx = −40 N·m

Cross product: a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.

Position vector from O to A

r = A − O = (−3, 2, −2) − (0, 0, 0) = (−3, 2, −2) m

Moment M = r × F

(r × F)x = ryFz − rzFy = 2·10 − (−2)·(−30) = −40 N·m
(r × F)y = rzFx − rxFz = (−2)·10 − (−3)·10 = 10 N·m
(r × F)z = rxFy − ryFx = (−3)·(−30) − 2·10 = 70 N·m

Requested component

Mx = −40 N·m

Answer

Mx = −40 N·m
3.Beam support reactions

Answer: RB = 165 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Replace each distributed load by its resultant (its area) acting at the centroid of the load diagram, and take moments about a support to remove that support’s reaction from the equation.

Moments about A

Counter-clockwise positive.

ΣMA = 0: RB·6 = 70·5 + 80·8
RB = 990/6 = 165 kN

Vertical equilibrium

RA = 70 + 80 − 165 = −15 kN

Answer

RB = 165 kN

RA is negative: the pin at A has to hold the beam down.

4.Beam support reactions

Answer: RB = 16.03 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Replace each distributed load by its resultant (its area) acting at the centroid of the load diagram, and take moments about a support to remove that support’s reaction from the equation.

Resultant of the distributed load

W = 3·3.5 = 10.5 kN, x̄ = (2.5 + 6)/2 = 4.25 m

Equilibrium

Moments about A, counter-clockwise positive. Then vertical force balance.

ΣMA = 0: RB·4.5 = 55·0.5 + 10.5·4.25
RB = 72.13/4.5 = 16.03 kN
RA = 65.5 − 16.03 = 49.47 kN

Answer

RB = 16.03 kN
5.Truss: method of joints

Answer: member DH

Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.

Joint D

CD and DE lie on one straight line and the joint carries no load. Balancing forces across that line leaves only DH.

ΣF⊥ = 0 → FDH = 0

Check with the method of joints

Solving all joints gives these member forces (T = tension, C = compression).

AB: 56.67 kN (T), BC: 56.67 kN (T), CD: 30 kN (T), DE: 30 kN (T), FG: 60 kN (C), GH: 60 kN (C), AF: 70.83 kN (C), HE: 37.5 kN (C), BF: 40 kN (T), CG: 25 kN (C), DH: 0, FC: 4.167 kN (T), HC: 37.5 kN (T)

Answer

Zero-force member: DH
6.Truss: method of joints

Answer: member CG

Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.

Joint C

BC and CD lie on one straight line and the joint carries no load. Balancing forces across that line leaves only CG.

ΣF⊥ = 0 → FCG = 0

Check with the method of joints

Solving all joints gives these member forces (T = tension, C = compression).

AB: 37.5 kN (T), BC: 42.5 kN (T), CD: 42.5 kN (T), DE: 36.25 kN (T), FG: 37.5 kN (C), GH: 36.25 kN (C), AF: 20.83 kN (C), HE: 60.42 kN (C), BF: 6.667 kN (T), CG: 0, DH: 48.33 kN (T), BG: 8.333 kN (C), DG: 10.42 kN (C)

Answer

Zero-force member: CG
7.Frames & machines

Answer: FO = 480.2 N

Machines: pliers, levers, linkages and clamps turn an input force into a larger or a differently directed output force. Draw one part as a free body and take moments about its pivot: the pin force drops out, and Fin·a = Fout·b gives the mechanical advantage a/b. The pin force then follows from ΣF = 0 on the same part. In a toggle, two links meet at a shallow angle θ; each link is a two-force member, so a small force F at the joint creates large link forces F/(2 sin θ) and a clamping force F/(2 tan θ).

Force at B

Q = 300·100/80 = 375 N

Pin reaction

Ox = 375 N, Oy = 300 N
FO = √(375² + 300²) = 480.2 N

Answer

FO = 480.2 N
8.Frames & machines

Answer: T = 15 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Whole frame: moments about A

By·4.8 = 15·2.4
By = 7.5 kN

Leg BC: moments about C

7.5·2.4 = T·1.2
T = 15 kN

Answer

T = 15 kN

A positive T means the tie is in tension, as assumed.

9.Shear force & bending moment

Answer: Mx = 34.38 kN·m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut. An applied couple makes the bending moment diagram jump by the size of the couple.

Support reactions

Moments about A, counter-clockwise positive: RB·L − M0 = 0. Vertical balance: RA + RB = 0.

RB = M0/L = 55/8 = 6.875 kN (upward)
RA = −RB = −6.875 kN (downward)

Cut just right of the couple

The left part now contains RA and the couple.

Mx = RA·a + M0 = −6.875·3 + 55 = 34.38 kN·m

Answer

Mx = 34.38 kN·m
10.Shear force & bending moment

Answer: xc = 5.625 m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut. Maximum moment: since dM/dx = V, the bending moment has its peak where the shear force passes through zero, either at a point load or inside a distributed load.

Support reactions

Equilibrium of the whole beam, including the load on the overhang.

UDL resultant: W = w·ℓ = 5·7.5 = 37.5 kN, acting at x̄ = 3.75 m
ΣMA = 0: RB·6 = 5·7.5·3.75
RB = 140.6/6 = 23.44 kN
ΣFy = 0: RA = 37.5 − 23.44 = 14.06 kN

Zero moment

Between the supports M(x) = RA·x − w·x²/2. Apart from x = 0 it is zero at x = 2RA/w.

RA·xc − w·xc²/2 = 0
xc = 2·14.06/5 = 5.625 m

Answer

xc = 5.625 m
11.Centroid & second moment of area

Answer: ȳ = 24.09 mm

Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.

Split into rectangles

Take the base at full width and the two legs above it (height h − t), so nothing is counted twice.

base: A1 = 100·10 = 1000 mm², y1 = 5 mm
two legs: A2 = 2·10·60 = 1200 mm², y2 = 10 + 60/2 = 40 mm

Centroid

ȳ = (1000·5 + 1200·40)/2200 = 24.09 mm

Answer

ȳ = 24.09 mm
12.Centroid & second moment of area

Answer: Ix = 137.6 × 10⁶ mm⁴

Sections with holes: treat a hole as a negative area. The centroid is ȳ = (A₁y₁ − A₂y₂)/(A₁ − A₂), with A₁, y₁ for the full plate and A₂, y₂ for the hole. For the second moment of area about the centroidal axis, use the parallel-axis theorem for each part and subtract the hole: I = (Ic1 + A₁d₁²) − (Ic2 + A₂d₂²), where d is the distance from each part's own centroid to the axis through ȳ. A rectangle has Ic = bh³/12 and a circle Ic = πd⁴/64.

Centroid

ȳ = (28800·120 − 900·144)/(28800 − 900) = 119.2 mm

Full plate about ȳ

120·240³/12 + 28800·0.7742² = 138.3 × 10⁶ mm⁴

Hole about ȳ

30·30³/12 + 900·24.77² = 0.6199 × 10⁶ mm⁴

Subtract

Ix = 137.6 × 10⁶ mm⁴

Answer

Ix = 137.6 × 10⁶ mm⁴

ExamProblems · examproblems.com/courses/statics