Statics: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Vectors: dot & cross product

Magnitude
|a| = √(ax² + ay² + az²)
Unit vector
û = a/|a|
Components from an angle
Fx = F·cos θ, Fy = F·sin θ
Dot product
a·b = axbx + ayby + azbz = |a||b|cos θ
Scalar projection of a onto b
a·b/|b|
Work
W = F·d
Cross product
a × b = (aybz − azby, azbx − axbz, axby − aybx)
Areas
parallelogram |a × b|, triangle ½|a × b|
Moment about O
MO = r × F, r = A − O
Volume of a parallelepiped
V = |a·(b × c)|

Method

  1. Write every vector in components; for a force given by a magnitude and an angle, use F·cos θ and F·sin θ.
  2. For lengths and directions use the magnitude √(x² + y² + z²) and the unit vector a/|a|.
  3. Use the dot product for angles, projections, perpendicularity and work: a·b = |a||b|cos θ.
  4. Use the cross product for perpendicular vectors, areas and moments: write the three components carefully, keeping the order a × b.

Beam support reactions

Equilibrium
ΣFx = 0, ΣFy = 0, ΣM = 0
Uniform load
resultant w·L at the middle of the load
Moment
M = F·d

Method

  1. Draw a free-body diagram and replace each support by its reactions.
  2. Replace every distributed load by a single force at its centroid.
  3. Take moments about one support to find the reaction at the other.
  4. Use ΣFy = 0 to find the remaining reaction, and check with a second moment equation.

Truss: method of joints

Method of joints
ΣFx = 0, ΣFy = 0 at each joint
Method of sections
ΣM = 0 about a cut point
Member force
positive = tension, negative = compression

Method

  1. Find the support reactions for the whole truss.
  2. Method of joints: start at a joint with at most two unknown member forces and use ΣFx = 0 and ΣFy = 0.
  3. Method of sections: cut through the member you need and take moments about a point where the other unknown members meet.
  4. Assume tension; a negative answer means compression.

Frames & machines

Equilibrium of each member
ΣFx = 0, ΣFy = 0, ΣM = 0
Two-force member
force along the line through its two pins
Pin force
equal and opposite on the two members it joins
Magnitude of a pin force
F = √(Fx² + Fy²)
Lever, pliers, bell crank
Fin·a = Fout·b
Toggle
Flink = F/(2 sin θ), Q = F/(2 tan θ)
Uniform load
resultant w·L at the middle of the load

Method

  1. Draw the whole structure and find the support reactions if there are no more than three unknowns.
  2. Spot the two-force members: loaded only at two pins, their force acts along the line between the pins.
  3. Take the frame apart and draw every member on its own, with equal and opposite pin forces where members meet.
  4. For each member, take moments about a pin with unknown forces, then use ΣFx = 0 and ΣFy = 0; combine components into a magnitude at the end.

Shear force & bending moment

Shear and moment
V = ΣF on one side, M = ΣF·d on one side
Bending stress
σ = M·y/I
Rectangle
I = bh³/12
Section modulus
W = I/ymax
Simply supported, uniform load
Mmax = wL²/8

Method

  1. Find the support reactions from equilibrium of the whole beam.
  2. Cut the beam at the section you need and keep one side.
  3. Shear force: sum of the vertical forces on that side. Bending moment: sum of their moments about the cut.
  4. For the maximum moment, find where the shear force is zero.

Centroid & second moment of area

Centroid
ȳ = ΣAiyi/ΣAi
Rectangle
I = bh³/12
Parallel-axis theorem
I = Ic + A·d²
Composite section
I = Σ(Ic,i + Aidi²)

2Practice problems

1.Vectors: dot & cross productMedium
xyzab

Find the value of k for which the vectors a = (−2, −1, 3) and b = (2, −6, k) are perpendicular.

a = (−2, −1, 3)b = (2, −6, k)
k =
2.Vectors: dot & cross productHard
xyzabc

Find the volume V of the parallelepiped whose edges from one corner are a = (1, −5, 5), b = (−4, 2, 1) and c = (0, −1, 3).

a = (1, −5, 5)b = (−4, 2, 1)c = (0, −1, 3)
V =
3.Beam support reactionsMedium
P1​ = 50 kNP2​ = 20 kNABCRA​ = ?1.5 m1 m1.5 m

The beam has a pin at A and a roller at B, 2.5 m from A, and overhangs B to the free end C. Find the vertical reaction RA, taking upward as positive.

AB = 2.5 mAC = 4 mP1 = 50 kN at 1.5 mP2 = 20 kN at 4 m
RA = kN
4.Beam support reactionsHard
w0​ = 12 kN/mP = 70 kNABMA​ = ?1.5 m2.5 m

The cantilever beam is fixed to the wall at A. It carries a linearly varying load that is zero at the wall and rises to 12 kN/m at the free end B, plus a point load P at 1.5 m from the wall. Find the magnitude of the reaction moment MA at the wall.

L = 4 mw0 = 12 kN/mP = 70 kN at 1.5 m
MA = kN·m
5.Truss: method of jointsMedium
ABBCACACB25 kN8 m1 m3 m

Use the method of joints to find the force FBC in member BC. Give tension as positive and compression as negative.

span = 8 mheight = 3 mB is 1 m from Avertical load = 25 kN
FBC = kN
6.Truss: method of jointsHard
ABBCACACB60 kN25 kN4 m3 m2 m

Use the method of joints to find the force FBC in member BC. Give tension as positive and compression as negative.

span = 4 mheight = 2 mB is 3 m from Avertical load = 60 kNhorizontal load = 25 kN ←
FBC = kN
7.Frames & machinesMedium
15 kN4 m4 m1.8 mABCK

The frame shown has pins at A, B and C; A and C are fixed to the ground 4 m apart, and B is 4 m above the ground and 1.8 m to the right of A. A vertical load of 15 kN acts on member AB at K, 0.72 m (horizontally) from A. Find the force FBC in member BC.

P = 15 kNL = 4 mH = 4 mhorizontal distance A to B = 1.8 mhorizontal distance A to K = 0.72 m
FBC = kN
8.Frames & machinesHard
w = 5 kN/m15 kN1 m1.5 m1.5 mABCD

The beam AB of the wall bracket shown is pinned at A and propped by the strut CD (C is 1.5 m below A). The beam carries a uniform load of 5 kN/m over its full length and a point load of 15 kN at its free end B. Find the force FCD in the strut.

w = 5 kN/mP = 15 kNAD = 1 mAB = 2.5 mAC = 1.5 m
FCD = kN
9.Shear force & bending momentMedium
P1​ = 50 kNP2​ = 50 kNABC3 m5 m2 m

The beam rests on a pin at A and a roller at B and overhangs B by 2 m to the free end C. It carries a point load P1 between the supports and a point load P2 at C. Find the bending moment MB at support B. Use sagging moments positive and upward shear on the left face positive.

L = 10 mP1 = 50 kN at 3 mP2 = 50 kN at 10 msupports at x = 0 and x = 8 m
MB = kN·m
10.Shear force & bending momentHard
w = 12 kN/mAB7 m1 m

The simply supported beam carries a uniformly distributed load over part of its span. Find the distance x0 from A to the section where the bending moment is largest.

L = 8 mw = 12 kN/m from 0 to 7 m
x0 = m
11.Centroid & second moment of areaMedium
240100t = 20xdimensions in mm

A channel section lies with its open side up: a base plate 240 mm wide with two upright legs, 100 mm high overall. Base and legs are all 20 mm thick. Find its second moment of area Ix about the horizontal axis x through its centroid.

b = 240 mmh = 100 mmt = 20 mm
Ix = × 10⁶ mm⁴
12.Centroid & second moment of areaHard
1202018020xM = 20 kN·mdimensions in mm

The T-section is used as a beam with the flange on top and carries a sagging bending moment of 20 kN·m. Find the size of the bending stress σtop at the top edge.

bf = 120 mmtf = 20 mmtw = 20 mmhw = 180 mmM = 20 kN·m
σtop = MPa

3Solutions

1.Vectors: dot & cross product

Answer: k = −0.6667

Dot product: a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.

Dot product equals zero

a·b = (−2)·2 + (−1)·(−6) + 3·k = 0
2 + 3·k = 0

Solve for k

k = −2/3 = −0.6667

Answer

k = −0.6667
2.Vectors: dot & cross product

Answer: V = 33

Cross product: a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.

Cross product b × c

(b × c)x = bycz − bzcy = 2·3 − 1·(−1) = 7
(b × c)y = bzcx − bxcz = 1·0 − (−4)·3 = 12
(b × c)z = bxcy − bycx = (−4)·(−1) − 2·0 = 4

Dot product with a

a·(b × c) = 1·7 + (−5)·12 + 5·4 = −33
V = |−33| = 33

Answer

V = 33
3.Beam support reactions

Answer: RA = 8 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Replace each distributed load by its resultant (its area) acting at the centroid of the load diagram, and take moments about a support to remove that support’s reaction from the equation.

Moments about A

Counter-clockwise positive.

ΣMA = 0: RB·2.5 = 50·1.5 + 20·4
RB = 155/2.5 = 62 kN

Vertical equilibrium

RA = 50 + 20 − 62 = 8 kN

Answer

RA = 8 kN
4.Beam support reactions

Answer: MA = 169 kN·m

Cantilever equilibrium: a fixed support can push up and also resist rotation, so it gives a vertical reaction RA and a reaction moment MA. ΣFy = 0 gives RA, and moments about the wall give MA = Σ(load × distance from the wall). A distributed load acts as its resultant at the centroid of the load diagram.

Resultant of the triangular load

W = ½·12·4 = 24 kN
x̄ = 2L/3 = 2.667 m

Moment about the wall

MA = W·x̄ + P·a = 24·2.667 + 70·1.5 = 169 kN·m

Answer

MA = 169 kN·m
5.Truss: method of joints

Answer: FBC = −7.933 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB25 kNAy​Cy​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·8 = 25·1 → Cy = 3.125 kN
ΣFy = 0: Ay = 25 − 3.125 = 21.88 kN

Joint C

The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.

sin γ = 3/7.616 = 0.3939, cos γ = 7/7.616 = 0.9191
ΣFy = 0: Cy + FBC·sin γ = 0 → FBC = −3.125/0.3939 = −7.933 kN

Answer

FBC = −7.933 kN (compression)
6.Truss: method of joints

Answer: FBC = −36.34 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB60 kN25 kNAy​Cy​Ax​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·4 = 60·3 − 25·2 → Cy = 32.5 kN
ΣFy = 0: Ay = 60 − 32.5 = 27.5 kN
ΣFx = 0: Ax = 25 kN

Joint C

The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.

sin γ = 2/2.236 = 0.8944, cos γ = 1/2.236 = 0.4472
ΣFy = 0: Cy + FBC·sin γ = 0 → FBC = −32.5/0.8944 = −36.34 kN

Answer

FBC = −36.34 kN (compression)
7.Frames & machines

Answer: FBC = 3.081 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Two-force member BC

BC = √(2.2² + 4²) = 4.565 m

Whole frame: moments about A

The ground pushes on BC at C along CB; its horizontal component passes through A, only the vertical one has a moment.

FBC·(4/4.565)·4 = 15·0.72
FBC = 3.081 kN (compression)

Answer

FBC = 3.081 kN
8.Frames & machines

Answer: FCD = 63.85 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Resultant of the uniform load

w·L = 5·2.5 = 12.5 kN at 1.25 m

Moments about A for the beam

FCD·0.8321·1 = 12.5·1.25 + 15·2.5 = 53.13 kN·m
FCD = 63.85 kN

Answer

FCD = 63.85 kN
9.Shear force & bending moment

Answer: MB = −100 kN·m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.

Support reactions

Equilibrium of the whole beam. The overhang load also acts about A.

ΣMA = 0: RB·8 = 50·3 + 50·10
RB = 650/8 = 81.25 kN
ΣFy = 0: RA = 100 − 81.25 = 18.75 kN

Cut at B and keep the overhang

Only P2 acts on the overhang, with lever arm a. It bends the beam upward over the support (hogging).

MB = −P2·a = −50·2 = −100 kN·m

Answer

MB = −100 kN·m
10.Shear force & bending moment

Answer: x0 = 3.938 m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut. Maximum moment: since dM/dx = V, the bending moment has its peak where the shear force passes through zero, either at a point load or inside a distributed load.

Support reactions

Equilibrium of the whole beam.

UDL resultant: W = w·ℓ = 12·7 = 84 kN, acting at x̄ = 3.5 m
ΣMA = 0: RB·8 = 12·7·3.5
RB = 294/8 = 36.75 kN
ΣFy = 0: RA = 84 − 36.75 = 47.25 kN

Zero shear

The shear force starts at RA, stays constant over any unloaded part and falls with slope w inside the load.

RA − w·(x0 − 0) = 0
x0 = 0 + 47.25/12 = 3.938 m

Answer

x0 = 3.938 m
11.Centroid & second moment of area

Answer: Ix = 6.667 × 10⁶ mm⁴

Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.

Split into rectangles

Take the base at full width and the two legs above it (height h − t), so nothing is counted twice.

base: A1 = 240·20 = 4800 mm², y1 = 10 mm
two legs: A2 = 2·20·80 = 3200 mm², y2 = 20 + 80/2 = 60 mm

Centroid

ȳ = (4800·10 + 3200·60)/8000 = 30 mm

Parallel-axis theorem

base: 240·20³/12 + 4800·(10 − 30)² = 2.08 × 10⁶ mm⁴
two legs: 2·20·80³/12 + 3200·(60 − 30)² = 4.587 × 10⁶ mm⁴
Ix = 2.08 × 10⁶ + 4.587 × 10⁶
Ix = 6.667 × 10⁶ mm⁴ = 6.667 × 10⁶ mm⁴

Answer

Ix = 6.667 × 10⁶ mm⁴
12.Centroid & second moment of area

Answer: σtop = 57.85 MPa

Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.

Split into two rectangles

Measure every y from the bottom edge.

flange: Af = 120·20 = 2400 mm², yf = 180 + 20/2 = 190 mm
web: Aw = 20·180 = 3600 mm², yw = 180/2 = 90 mm

Centroid

ȳ = (Afyf + Awyw)/(Af + Aw) = (2400·190 + 3600·90)/6000 = 130 mm

Parallel-axis theorem

flange: 120·20³/12 + 2400·(190 − 130)² = 8.72 × 10⁶ mm⁴
web: 20·180³/12 + 3600·(90 − 130)² = 1.548 × 10⁷ mm⁴
Ix = 8.72 × 10⁶ + 1.548 × 10⁷ = 2.42 × 10⁷ mm⁴

Bending stress

The top edge is h − ȳ from the axis.

y = 200 − 130 = 70 mm
σ = M·y/I = 2 × 10⁷·70/2.42 × 10⁷ = 57.85 MPa

Answer

σtop = 57.85 MPa

ExamProblems · examproblems.com/courses/statics