In the print window, choose “Save as PDF” to keep a copy on your device.
1Formulas and methods
Vectors: dot & cross product
Magnitude
|a| = √(ax² + ay² + az²)
Unit vector
û = a/|a|
Components from an angle
Fx = F·cos θ, Fy = F·sin θ
Dot product
a·b = axbx + ayby + azbz = |a||b|cos θ
Scalar projection of a onto b
a·b/|b|
Work
W = F·d
Cross product
a × b = (aybz − azby, azbx − axbz, axby − aybx)
Areas
parallelogram |a × b|, triangle ½|a × b|
Moment about O
MO = r × F, r = A − O
Volume of a parallelepiped
V = |a·(b × c)|
Method
Write every vector in components; for a force given by a magnitude and an angle, use F·cos θ and F·sin θ.
For lengths and directions use the magnitude √(x² + y² + z²) and the unit vector a/|a|.
Use the dot product for angles, projections, perpendicularity and work: a·b = |a||b|cos θ.
Use the cross product for perpendicular vectors, areas and moments: write the three components carefully, keeping the order a × b.
Beam support reactions
Equilibrium
ΣFx = 0, ΣFy = 0, ΣM = 0
Uniform load
resultant w·L at the middle of the load
Moment
M = F·d
Method
Draw a free-body diagram and replace each support by its reactions.
Replace every distributed load by a single force at its centroid.
Take moments about one support to find the reaction at the other.
Use ΣFy = 0 to find the remaining reaction, and check with a second moment equation.
Truss: method of joints
Method of joints
ΣFx = 0, ΣFy = 0 at each joint
Method of sections
ΣM = 0 about a cut point
Member force
positive = tension, negative = compression
Method
Find the support reactions for the whole truss.
Method of joints: start at a joint with at most two unknown member forces and use ΣFx = 0 and ΣFy = 0.
Method of sections: cut through the member you need and take moments about a point where the other unknown members meet.
Assume tension; a negative answer means compression.
Frames & machines
Equilibrium of each member
ΣFx = 0, ΣFy = 0, ΣM = 0
Two-force member
force along the line through its two pins
Pin force
equal and opposite on the two members it joins
Magnitude of a pin force
F = √(Fx² + Fy²)
Lever, pliers, bell crank
Fin·a = Fout·b
Toggle
Flink = F/(2 sin θ), Q = F/(2 tan θ)
Uniform load
resultant w·L at the middle of the load
Method
Draw the whole structure and find the support reactions if there are no more than three unknowns.
Spot the two-force members: loaded only at two pins, their force acts along the line between the pins.
Take the frame apart and draw every member on its own, with equal and opposite pin forces where members meet.
For each member, take moments about a pin with unknown forces, then use ΣFx = 0 and ΣFy = 0; combine components into a magnitude at the end.
Shear force & bending moment
Shear and moment
V = ΣF on one side, M = ΣF·d on one side
Bending stress
σ = M·y/I
Rectangle
I = bh³/12
Section modulus
W = I/ymax
Simply supported, uniform load
Mmax = wL²/8
Method
Find the support reactions from equilibrium of the whole beam.
Cut the beam at the section you need and keep one side.
Shear force: sum of the vertical forces on that side. Bending moment: sum of their moments about the cut.
For the maximum moment, find where the shear force is zero.
Centroid & second moment of area
Centroid
ȳ = ΣAiyi/ΣAi
Rectangle
I = bh³/12
Parallel-axis theorem
I = Ic + A·d²
Composite section
I = Σ(Ic,i + Aidi²)
2Practice problems
1.Vectors: dot & cross productMedium
Find the scalar projection compb a of a = (−5, −5, −6) onto b = (−2, −6, 3), that is, the component of a in the direction of b.
a = (−5, −5, −6)b = (−2, −6, 3)
compb a =
2.Vectors: dot & cross productHard
The unit vector n̂ is perpendicular to both a = (−5, 5, 1) and b = (−3, −1, 5) and has a positive z-component. Find its y-component n̂y.
a = (−5, 5, 1)b = (−3, −1, 5)n̂z > 0
n̂y =
3.Beam support reactionsMedium
The simply supported beam has a pin at A and a roller at B. It carries a point load P at 1 m from A and a counter-clockwise couple M at 1.5 m from A. Find the vertical reaction RA, taking upward as positive.
L = 5 mP = 20 kN at 1 mM = 25 kN·m (counter-clockwise) at 1.5 m
RA = kN
4.Beam support reactionsHard
The simply supported beam has a pin at A and a roller at B. A load P acts at 9 m from A, inclined at 40° to the horizontal, and a vertical load Q acts at 3 m from A. Find the magnitude of the total reaction force RA at the pin A.
L = 10 mP = 55 kN at 9 m, θ = 40°Q = 60 kN at 3 m
RA = kN
5.Truss: method of jointsMedium
Use the method of joints to find the force FAB in member AB. Give tension as positive and compression as negative.
span = 8 mheight = 4 mB is 1 m from Avertical load = 35 kN
FAB = kN
6.Truss: method of jointsHard
Exactly one member of this truss carries no force under these loads. Which is the zero-force member? Click it in the diagram.
D: 30 kN ↓H: 15 kN ←
1member AB
2member BC
3member CD
4member DE
5member FG
6member GH
7member AF
8member HE
9member BF
10member CG
11member DH
12member BG
13member DG
7.Frames & machinesMedium
A horizontal beam AB is pinned to a wall at A and propped by the strut CD, pinned to the wall at C, 0.5 m below A. A load of 15 kN hangs at B. Neglect the weights. Find the magnitude of the pin force A on the beam at A.
P = 15 kNAD = 1 mAB = 2.4 mAC = 0.5 m
A = kN
8.Frames & machinesHard
The A-frame shown stands on a pin at A and a roller at B, 4 m apart, with its apex pin C 2.4 m high and the horizontal tie DE 0.8 m above the ground. A vertical load of 20 kN acts on leg AC at K, 1.5 m (horizontally) from A. Find the magnitude of the force C that the pin C exerts on leg BC.
P = 20 kNAB = 4 mheight of C = 2.4 mheight of DE = 0.8 mhorizontal distance A to K = 1.5 m
C = kN
9.Shear force & bending momentMedium
The simply supported beam carries a clockwise couple M0 = 45 kN·m at x = 3 m from A, and no other load. Find the bending moment Mx just to the left of the couple. Use sagging moments positive and upward shear on the left face positive.
L = 5 mM0 = 45 kN·m clockwise, at 3 m
Mx = kN·m
10.Shear force & bending momentHard
Find the bending moment Mx at the section x = 1 m from support A. Use sagging moments positive and upward shear on the left face positive.
L = 8 mP = 10 kN at 1 mw = 2 kN/m from 0 to 8 mx = 1 m
Mx = kN·m
11.Centroid & second moment of areaMedium
A hollow rectangular (box) section has outer width B = 180 mm, outer height H = 375 mm and a uniform wall thickness t = 18 mm. Find its radius of gyration r about the horizontal centroidal axis.
B = 180 mmH = 375 mmt = 18 mm
r = mm
12.Centroid & second moment of areaHard
A welded I-section has a top flange 100 × 12 mm, a web 270 mm high and 14 mm thick, and a bottom flange 300 × 22 mm (width × thickness). Find its second moment of area Ix about the horizontal axis x through its centroid.
top flange: 100 × 12 mmweb: 14 × 270 mmbottom flange: 300 × 22 mm
Ix = × 10⁶ mm⁴
3Solutions
1.Vectors: dot & cross product
Answer: compb a = 3.143
Dot product:a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.
Dot product
a·b = (−5)·(−2) + (−5)·(−6) + (−6)·3 = 22
Length of b
|b| = √((−2)² + (−6)² + 3²) = 7
Scalar projection
compb a = a·b/|b| = 22/7 = 3.143
Answer
compb a = 3.143
2.Vectors: dot & cross product
Answer: n̂y = 0.557
Cross product:a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.
Cross product
(a × b)x = aybz − azby = 5·5 − 1·(−1) = 26
(a × b)y = azbx − axbz = 1·(−3) − (−5)·5 = 22
(a × b)z = axby − aybx = (−5)·(−1) − 5·(−3) = 20
Normalise
The z-component of a × b is already positive.
|a × b| = √(26² + 22² + 20²) = 39.5
n̂ = (26, 22, 20)/39.5 = (0.6583, 0.557, 0.5064)
n̂y = 0.557
Answer
n̂y = 0.557
3.Beam support reactions
Answer: RA = 21 kN
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Replace each distributed load by its resultant (its area) acting at the centroid of the load diagram, and take moments about a support to remove that support’s reaction from the equation.
Moments about A
Counter-clockwise positive.
ΣMA = 0: RB·5 − 20·1 + 25 = 0
RB = −5/5 = −1 kN
Vertical equilibrium
RA = 20 − (−1) = 21 kN
Answer
RA = 21 kN
A negative reaction acts downward.
4.Beam support reactions
Answer: RA = 62.04 kN
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Replace each distributed load by its resultant (its area) acting at the centroid of the load diagram, and take moments about a support to remove that support’s reaction from the equation.
Components of P
Pv = 55·sin 40° = 35.35 kN
Ph = 55·cos 40° = 42.13 kN
Reactions
ΣMA = 0: RB·10 = 35.35·9 + 60·3 → RB = 49.82 kN
Ay = 35.35 + 60 − 49.82 = 45.54 kN
Ax = Ph = 42.13 kN
Resultant at A
RA = √(42.13² + 45.54²) = 62.04 kN
Answer
RA = 62.04 kN
5.Truss: method of joints
Answer: FAB = −31.57 kN
Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.
Support reactions
Equilibrium of the whole truss. Moments about A, counter-clockwise positive.
ΣMA = 0: Cy·8 = 35·1 → Cy = 4.375 kN
ΣFy = 0: Ay = 35 − 4.375 = 30.63 kN
Joint A
Assume every member is in tension (pulling away from the joint). Only AB has a vertical component at A.
sin α = 4/4.123 = 0.9701
ΣFy = 0: Ay + FAB·sin α = 0
FAB = −30.63/0.9701 = −31.57 kN
Answer
FAB = −31.57 kN (compression)
6.Truss: method of joints
Answer: member CG
Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.
Joint C
BC and CD lie on one straight line and the joint carries no load. Balancing forces across that line leaves only CG.
ΣF⊥ = 0 → FCG = 0
Check with the method of joints
Solving all joints gives these member forces (T = tension, C = compression).
Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.
Strut force
FCD = 15·2.4/(0.4472·1) = 80.5 kN
Components at A
Ax = FCD·cos α = 72 kN (towards the wall)
Ay = 15 − FCD·sin α = −21 kN
Magnitude
A = √(72² + −21²) = 75 kN
Answer
A = 75 kN
A negative Ay means the wall pulls the beam down at A.
8.Frames & machines
Answer: C = 12.01 kN
Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.
Support reaction at B
By = 20·1.5/4 = 7.5 kN
Tie force
T = 7.5·2/1.6 = 9.375 kN
Pin force on BC
Cx = 9.375 kN, Cy = −7.5 kN
C = √(9.375² + 7.5²) = 12.01 kN
Answer
C = 12.01 kN
9.Shear force & bending moment
Answer: Mx = −27 kN·m
Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut. An applied couple makes the bending moment diagram jump by the size of the couple.
Support reactions
Moments about A, counter-clockwise positive: RB·L − M0 = 0. Vertical balance: RA + RB = 0.
RB = M0/L = 45/5 = 9 kN (upward)
RA = −RB = −9 kN (downward)
Cut just left of the couple
The left part contains only RA.
Mx = RA·a = −9·3 = −27 kN·m
Answer
Mx = −27 kN·m
10.Shear force & bending moment
Answer: Mx = 15.75 kN·m
Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.
Support reactions
Equilibrium of the whole beam.
UDL resultant: W = w·ℓ = 2·8 = 16 kN, acting at x̄ = 4 m
ΣMA = 0: RB·8 = 10·1 + 2·8·4
RB = 74/8 = 9.25 kN
ΣFy = 0: RA = 26 − 9.25 = 16.75 kN
Cut at x = 1 m and keep the left part
Only forces left of the cut appear. A UDL portion acts as one force at the middle of that portion.
M = RA·x − (each load left of the cut × its distance to the cut)
Mx = 16.75·1 − 2·1·0.5 = 15.75 kN·m
Answer
Mx = 15.75 kN·m
11.Centroid & second moment of area
Answer: r = 131.6 mm
Second moment of area: for a rectangle about its own centroidal axis I = bh³/12, and about its base bh³/3 (parallel-axis theorem I = Ic + A·d²). A hole is handled by subtracting its I, as long as both parts share the same axis. The elastic section modulus is S = I/c, where c is the distance to the extreme fibre. The radius of gyration r = √(I/A) is the distance at which the whole area would give the same I; it is used in column buckling.
Net area and second moment of area
b = 144 mm, h = 339 mm
A = BH − bh = 180·375 − 144·339 = 18684 mm²
I = (BH³ − bh³)/12 = 3.235 × 10⁸ mm⁴
Radius of gyration
r = √(I/A) = √(3.235 × 10⁸/18684) = 131.6 mm
Answer
r = 131.6 mm
12.Centroid & second moment of area
Answer: Ix = 133.3 × 10⁶ mm⁴
Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.
Split into three rectangles
Measure every y from the bottom edge.
top flange: A = 1200 mm², y = 298 mm
web: A = 3780 mm², y = 157 mm
bottom flange: A = 6600 mm², y = 11 mm
Centroid
ȳ = (1200·298 + 3780·157 + 6600·11)/11580 = 88.4 mm
Parallel-axis theorem
top flange: 100·12³/12 + 1200·209.6² = 5.273 × 10⁷ mm⁴