Statics: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Vectors: dot & cross product

Magnitude
|a| = √(ax² + ay² + az²)
Unit vector
û = a/|a|
Components from an angle
Fx = F·cos θ, Fy = F·sin θ
Dot product
a·b = axbx + ayby + azbz = |a||b|cos θ
Scalar projection of a onto b
a·b/|b|
Work
W = F·d
Cross product
a × b = (aybz − azby, azbx − axbz, axby − aybx)
Areas
parallelogram |a × b|, triangle ½|a × b|
Moment about O
MO = r × F, r = A − O
Volume of a parallelepiped
V = |a·(b × c)|

Method

  1. Write every vector in components; for a force given by a magnitude and an angle, use F·cos θ and F·sin θ.
  2. For lengths and directions use the magnitude √(x² + y² + z²) and the unit vector a/|a|.
  3. Use the dot product for angles, projections, perpendicularity and work: a·b = |a||b|cos θ.
  4. Use the cross product for perpendicular vectors, areas and moments: write the three components carefully, keeping the order a × b.

Beam support reactions

Equilibrium
ΣFx = 0, ΣFy = 0, ΣM = 0
Uniform load
resultant w·L at the middle of the load
Moment
M = F·d

Method

  1. Draw a free-body diagram and replace each support by its reactions.
  2. Replace every distributed load by a single force at its centroid.
  3. Take moments about one support to find the reaction at the other.
  4. Use ΣFy = 0 to find the remaining reaction, and check with a second moment equation.

Truss: method of joints

Method of joints
ΣFx = 0, ΣFy = 0 at each joint
Method of sections
ΣM = 0 about a cut point
Member force
positive = tension, negative = compression

Method

  1. Find the support reactions for the whole truss.
  2. Method of joints: start at a joint with at most two unknown member forces and use ΣFx = 0 and ΣFy = 0.
  3. Method of sections: cut through the member you need and take moments about a point where the other unknown members meet.
  4. Assume tension; a negative answer means compression.

Frames & machines

Equilibrium of each member
ΣFx = 0, ΣFy = 0, ΣM = 0
Two-force member
force along the line through its two pins
Pin force
equal and opposite on the two members it joins
Magnitude of a pin force
F = √(Fx² + Fy²)
Lever, pliers, bell crank
Fin·a = Fout·b
Toggle
Flink = F/(2 sin θ), Q = F/(2 tan θ)
Uniform load
resultant w·L at the middle of the load

Method

  1. Draw the whole structure and find the support reactions if there are no more than three unknowns.
  2. Spot the two-force members: loaded only at two pins, their force acts along the line between the pins.
  3. Take the frame apart and draw every member on its own, with equal and opposite pin forces where members meet.
  4. For each member, take moments about a pin with unknown forces, then use ΣFx = 0 and ΣFy = 0; combine components into a magnitude at the end.

Shear force & bending moment

Shear and moment
V = ΣF on one side, M = ΣF·d on one side
Bending stress
σ = M·y/I
Rectangle
I = bh³/12
Section modulus
W = I/ymax
Simply supported, uniform load
Mmax = wL²/8

Method

  1. Find the support reactions from equilibrium of the whole beam.
  2. Cut the beam at the section you need and keep one side.
  3. Shear force: sum of the vertical forces on that side. Bending moment: sum of their moments about the cut.
  4. For the maximum moment, find where the shear force is zero.

Centroid & second moment of area

Centroid
ȳ = ΣAiyi/ΣAi
Rectangle
I = bh³/12
Parallel-axis theorem
I = Ic + A·d²
Composite section
I = Σ(Ic,i + Aidi²)

2Practice problems

1.Vectors: dot & cross productMedium
xyzab

Find the dot product a·b of a = (−2, 2, 6) and b = (7, 3, −5).

a = (−2, 2, 6)b = (7, 3, −5)
a·b =
2.Vectors: dot & cross productHard
xyzab

The unit vector n̂ is perpendicular to both a = (−3, 4, 2) and b = (5, 5, −2) and has a positive z-component. Find its y-component n̂y.

a = (−3, 4, 2)b = (5, 5, −2)n̂z > 0
n̂y =
3.Beam support reactionsMedium
w0​ = 15 kN/mABRA​ = ?6 m

The simply supported beam (pin at A, roller at B) carries a linearly varying load that falls from 15 kN/m at A to zero at B. Find the vertical support reaction RA.

L = 6 mw0 = 15 kN/m
RA = kN
4.Beam support reactionsHard
P = 15 kN, 60°Q = 65 kNABα = ?1.5 m2 m0.5 m

The simply supported beam has a pin at A and a roller at B. A load P acts at 3.5 m from A, inclined at 60° to the horizontal, and a vertical load Q acts at 1.5 m from A. Find the angle α between the total reaction force at the pin A and the horizontal.

L = 4 mP = 15 kN at 3.5 m, θ = 60°Q = 65 kN at 1.5 m
α = °
5.Truss: method of jointsMedium
ABCDEFGH15 kN40 kN4 × 4 m4 m

Exactly one member of this truss carries no force under these loads. Which is the zero-force member? Click it in the diagram.

B: 15 kN ↓G: 40 kN ↓
  1. 1member AB
  2. 2member BC
  3. 3member CD
  4. 4member DE
  5. 5member FG
  6. 6member GH
  7. 7member AF
  8. 8member HE
  9. 9member BF
  10. 10member CG
  11. 11member DH
  12. 12member BG
  13. 13member DG
6.Truss: method of jointsHard
ABBCACACB25 kN5 kN6 m4 m2 m

Use the method of joints to find the force FAC in member AC. Give tension as positive and compression as negative.

span = 6 mheight = 2 mB is 4 m from Avertical load = 25 kNhorizontal load = 5 kN ←
FAC = kN
7.Frames & machinesMedium
4 kN5 m1.2 m2.8 m1.25 mABCDEK

The A-frame shown stands on a pin at A and a roller at B, 5 m apart, with its apex pin C 4 m high and the horizontal tie DE 1.2 m above the ground. A vertical load of 4 kN acts on leg AC at K, 1.25 m (horizontally) from A. Find the tension T in the tie.

P = 4 kNAB = 5 mheight of C = 4 mheight of DE = 1.2 mhorizontal distance A to K = 1.25 m
T = kN
8.Frames & machinesHard
4 kN1.5 kN4 m2.5 mABC

A uniform horizontal boom AB of weight 1.5 kN is pinned to a wall at A and held by a cable from its end B to the point C on the wall, 2.5 m above A. A load of 4 kN hangs at B. Find the tension T in the cable.

W = 4 kNWb = 1.5 kNAB = 4 mAC = 2.5 m
T = kN
9.Shear force & bending momentMedium
M0​ = 25 kN·mAB1.5 m2.5 m

The simply supported beam carries a clockwise couple M0 = 25 kN·m at x = 1.5 m from A, and no other load. Find the bending moment Mx just to the right of the couple. Use sagging moments positive and upward shear on the left face positive.

L = 4 mM0 = 25 kN·m clockwise, at 1.5 m
Mx = kN·m
10.Shear force & bending momentHard
60 kN60 kNABCDEFG1 m1 m1 m1 m1 m1 m

The marks A to G split the beam into six equal parts. At which mark is the bending moment largest in size, sagging or hogging? Click it in the diagram.

60 kN @ 6 m60 kN @ 2 m
  1. 1A (x = 0 m)
  2. 2B (x = 1 m)
  3. 3C (x = 2 m)
  4. 4D (x = 3 m)
  5. 5E (x = 4 m)
  6. 6F (x = 5 m)
  7. 7G (x = 6 m)
11.Centroid & second moment of areaMedium
140170t = 16ȳ = ?dimensions in mm

A channel section lies with its open side up: a base plate 140 mm wide with two upright legs, 170 mm high overall. Base and legs are all 16 mm thick. Find the height ȳ of the centroid above the bottom edge.

b = 140 mmh = 170 mmt = 16 mm
ȳ = mm
12.Centroid & second moment of areaHard
100300122201812xdimensions in mm

A welded I-section has a top flange 100 × 12 mm, a web 220 mm high and 12 mm thick, and a bottom flange 300 × 18 mm (width × thickness). Find its second moment of area Ix about the horizontal axis x through its centroid.

top flange: 100 × 12 mmweb: 12 × 220 mmbottom flange: 300 × 18 mm
Ix = × 10⁶ mm⁴

3Solutions

1.Vectors: dot & cross product

Answer: a·b = −38

Dot product: a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.

Multiply matching components and add

a·b = (−2)·7 + 2·3 + 6·(−5) = (−14) + 6 + (−30) = −38

Answer

a·b = −38

Negative: the angle between the vectors is more than 90°.

2.Vectors: dot & cross product

Answer: n̂y = −0.1011

Cross product: a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.

Cross product

(a × b)x = aybz − azby = 4·(−2) − 2·5 = −18
(a × b)y = azbx − axbz = 2·5 − (−3)·(−2) = 4
(a × b)z = axby − aybx = (−3)·5 − 4·5 = −35

Normalise

The z-component of a × b is negative, so use −(a × b).

|a × b| = √((−18)² + 4² + (−35)²) = 39.56
n̂ = −(−18, 4, −35)/39.56 = (0.455, −0.1011, 0.8847)
n̂y = −0.1011

Answer

n̂y = −0.1011
3.Beam support reactions

Answer: RA = 30 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Replace each distributed load by its resultant (its area) acting at the centroid of the load diagram, and take moments about a support to remove that support’s reaction from the equation.

Resultant of the triangular load

W = ½·15·6 = 45 kN
x̄ = L/3 = 2 m

Equilibrium

Moments about A, counter-clockwise positive. Then vertical force balance.

ΣMA = 0: RB·6 = 45·2
RB = 15 kN
RA = 45 − 15 = 30 kN

Answer

RA = 30 kN
4.Beam support reactions

Answer: α = 79.93 °

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Replace each distributed load by its resultant (its area) acting at the centroid of the load diagram, and take moments about a support to remove that support’s reaction from the equation.

Components of P

Pv = 15·sin 60° = 12.99 kN
Ph = 15·cos 60° = 7.5 kN

Reactions

ΣMA = 0: RB·4 = 12.99·3.5 + 65·1.5 → RB = 35.74 kN
Ay = 12.99 + 65 − 35.74 = 42.25 kN
Ax = Ph = 7.5 kN

Direction at A

α = atan(Ay/Ax) = atan(42.25/7.5) = 79.93°

Answer

α = 79.93°
5.Truss: method of joints

Answer: member CG

Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.

Joint C

BC and CD lie on one straight line and the joint carries no load. Balancing forces across that line leaves only CG.

ΣF⊥ = 0 → FCG = 0

Check with the method of joints

Solving all joints gives these member forces (T = tension, C = compression).

AB: 31.25 kN (T), BC: 47.5 kN (T), CD: 47.5 kN (T), DE: 23.75 kN (T), FG: 31.25 kN (C), GH: 23.75 kN (C), AF: 44.19 kN (C), HE: 33.59 kN (C), BF: 31.25 kN (T), CG: 0, DH: 23.75 kN (T), BG: 22.98 kN (C), DG: 33.59 kN (C)

Answer

Zero-force member: CG
6.Truss: method of joints

Answer: FAC = 15 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB25 kN5 kNAy​Cy​Ax​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·6 = 25·4 − 5·2 → Cy = 15 kN
ΣFy = 0: Ay = 25 − 15 = 10 kN
ΣFx = 0: Ax = 5 kN

Joint C

The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.

sin γ = 2/2.828 = 0.7071, cos γ = 2/2.828 = 0.7071
ΣFy = 0: Cy + FBC·sin γ = 0 → FBC = −15/0.7071 = −21.21 kN
ΣFx = 0: −FAC − FBC·cos γ = 0 → FAC = −(−21.21)·0.7071 = 15 kN

Answer

FAC = 15 kN (tension)
7.Frames & machines

Answer: T = 0.8929 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Whole frame: moments about A

By = 4·1.25/5 = 1 kN

Leg BC: moments about C

1·2.5 = T·2.8
T = 0.8929 kN

Answer

T = 0.8929 kN
8.Frames & machines

Answer: T = 8.962 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Cable angle

BC = √(4² + 2.5²) = 4.717 m, sin β = 0.53

Moments about A

T·0.53·4 = 4·4 + 1.5·2
T = 8.962 kN

Answer

T = 8.962 kN
9.Shear force & bending moment

Answer: Mx = 15.63 kN·m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut. An applied couple makes the bending moment diagram jump by the size of the couple.

Support reactions

Moments about A, counter-clockwise positive: RB·L − M0 = 0. Vertical balance: RA + RB = 0.

RB = M0/L = 25/4 = 6.25 kN (upward)
RA = −RB = −6.25 kN (downward)

Cut just right of the couple

The left part now contains RA and the couple.

Mx = RA·a + M0 = −6.25·1.5 + 25 = 15.63 kN·m

Answer

Mx = 15.63 kN·m
10.Shear force & bending moment

Answer: E (x = 4 m)

Largest bending moment: M changes slope wherever the shear force changes, so its peaks sit where the shear force crosses zero: under a point load, inside a distributed load, or over a support of an overhang. At a fixed support of a cantilever the moment is largest at the wall. Compare the size of M at those places, sagging or hogging.

Support reactions

Take moments about one support, then use the vertical force balance.

R1 = 0 kN, R2 = 120 kN

Bending moment at every mark

Sum the moments of all forces on one side of the cut. Sagging is positive, hogging negative.

MA = 0, MB = 0, MC = 0, MD = −60, ME = −120 kN·m, MF = −60, MG = 0

Answer

Mark E: ME = −120 kN·m
11.Centroid & second moment of area

Answer: ȳ = 66.44 mm

Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.

Split into rectangles

Take the base at full width and the two legs above it (height h − t), so nothing is counted twice.

base: A1 = 140·16 = 2240 mm², y1 = 8 mm
two legs: A2 = 2·16·154 = 4928 mm², y2 = 16 + 154/2 = 93 mm

Centroid

ȳ = (2240·8 + 4928·93)/7168 = 66.44 mm

Answer

ȳ = 66.44 mm
12.Centroid & second moment of area

Answer: Ix = 76 × 10⁶ mm⁴

Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.

Split into three rectangles

Measure every y from the bottom edge.

top flange: A = 1200 mm², y = 244 mm
web: A = 2640 mm², y = 128 mm
bottom flange: A = 5400 mm², y = 9 mm

Centroid

ȳ = (1200·244 + 2640·128 + 5400·9)/9240 = 73.52 mm

Parallel-axis theorem

top flange: 100·12³/12 + 1200·170.5² = 3.489 × 10⁷ mm⁴
web: 12·220³/12 + 2640·54.48² = 1.848 × 10⁷ mm⁴
bottom flange: 300·18³/12 + 5400·64.52² = 2.262 × 10⁷ mm⁴
Ix = 3.489 × 10⁷ + 1.848 × 10⁷ + 2.262 × 10⁷
Ix = 7.6 × 10⁷ mm⁴ = 76 × 10⁶ mm⁴

Answer

Ix = 76 × 10⁶ mm⁴

ExamProblems · examproblems.com/courses/statics