The frame shown has pins at A, B and C; A and C are fixed to the ground 6 m apart, and B is 3 m above the ground and 2.7 m to the right of A. A vertical load of 12 kN acts on member AB at K, 0.675 m (horizontally) from A. Find the force FBC in member BC.
P = 12 kNL = 6 mH = 3 mhorizontal distance A to B = 2.7 mhorizontal distance A to K = 0.675 m
FBC = kN
8.Frames & machinesHard
The A-frame shown stands on a pin at A and a roller at B, 5 m apart, with its apex pin C 4.5 m high and the horizontal tie DE 1 m above the ground. A vertical load of 15 kN acts on leg AC at K, 1 m (horizontally) from A. Find the magnitude of the force C that the pin C exerts on leg BC.
P = 15 kNAB = 5 mheight of C = 4.5 mheight of DE = 1 mhorizontal distance A to K = 1 m
C = kN
9.Shear force & bending momentMedium
Find the bending moment Mx at the section x = 2 m from support A. Use sagging moments positive and upward shear on the left face positive.
L = 5 mw = 2 kN/m from 0 to 5 mx = 2 m
Mx = kN·m
10.Shear force & bending momentHard
The simply supported beam carries a uniformly distributed load over part of its span. Find the maximum bending moment Mmax in the beam.
L = 4 mw = 6 kN/m from 0 to 2 m
Mmax = kN·m
11.Centroid & second moment of areaMedium
A channel section lies with its open side up: a base plate 260 mm wide with two upright legs, 110 mm high overall. Base and legs are all 18 mm thick. Find the height ȳ of the centroid above the bottom edge.
b = 260 mmh = 110 mmt = 18 mm
ȳ = mm
12.Centroid & second moment of areaHard
A symmetric I-section has flanges 230 mm wide and 12 mm thick, an overall depth of 300 mm and a web 8 mm thick. It carries a bending moment of 80 kN·m about the axis x. Find the size of the bending stress σj at the junction of the web and the top flange.
Dot product:a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.
Dot product equals zero
a·b = 2·k + 1·6 + (−3)·(−6) = 0
24 + 2·k = 0
Solve for k
k = −24/2 = −12
Answer
k = −12
2.Vectors: dot & cross product
Answer: V = 38
Cross product:a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.
Cross product b × c
(b × c)x = bycz − bzcy = 5·(−2) − 1·(−4) = −6
(b × c)y = bzcx − bxcz = 1·5 − 0·(−2) = 5
(b × c)z = bxcy − bycx = 0·(−4) − 5·5 = −25
Dot product with a
a·(b × c) = 2·(−6) + 5·5 + (−1)·(−25) = 38
V = |38| = 38
Answer
V = 38
3.Beam support reactions
Answer: RA = 11.25 kN
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.
Free-body diagram
Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.
Equilibrium
Moments about A, counter-clockwise positive. Then vertical force balance.
ΣMA = 0: RB·4 = 10·2.5 + 30·3
RB = 115/4 = 28.75 kN
ΣFy = 0: RA = 40 − 28.75 = 11.25 kN
Answer
RA = 11.25 kN
4.Beam support reactions
Answer: RB = 26.75 kN
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.
Free-body diagram
Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.
Equilibrium
Moments about A, counter-clockwise positive. Then vertical force balance.
UDL resultant: W = w·ℓ = 4·3 = 12 kN, acting at x̄ = 4.5 m
ΣMA = 0: RB·8 = 40·4 + 4·3·4.5
RB = 214/8 = 26.75 kN
ΣFy = 0: RA = 52 − 26.75 = 25.25 kN
Answer
RB = 26.75 kN
5.Truss: method of joints
Answer: FAB = −20.12 kN
Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.
Support reactions
Equilibrium of the whole truss. Moments about A, counter-clockwise positive.
ΣMA = 0: Cy·5 = 45·4 → Cy = 36 kN
ΣFy = 0: Ay = 45 − 36 = 9 kN
Joint A
Assume every member is in tension (pulling away from the joint). Only AB has a vertical component at A.
sin α = 2/4.472 = 0.4472
ΣFy = 0: Ay + FAB·sin α = 0
FAB = −9/0.4472 = −20.12 kN
Answer
FAB = −20.12 kN (compression)
6.Truss: method of joints
Answer: member DH
Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.
Joint D
CD and DE lie on one straight line and the joint carries no load. Balancing forces across that line leaves only DH.
ΣF⊥ = 0 → FDH = 0
Check with the method of joints
Solving all joints gives these member forces (T = tension, C = compression).
Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.
Two-force member BC
BC = √(3.3² + 3²) = 4.46 m
Whole frame: moments about A
The ground pushes on BC at C along CB; its horizontal component passes through A, only the vertical one has a moment.
FBC·(3/4.46)·6 = 12·0.675
FBC = 2.007 kN (compression)
Answer
FBC = 2.007 kN
8.Frames & machines
Answer: C = 3.687 kN
Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.
Support reaction at B
By = 15·1/5 = 3 kN
Tie force
T = 3·2.5/3.5 = 2.143 kN
Pin force on BC
Cx = 2.143 kN, Cy = −3 kN
C = √(2.143² + 3²) = 3.687 kN
Answer
C = 3.687 kN
9.Shear force & bending moment
Answer: Mx = 6 kN·m
Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.
Support reactions
Equilibrium of the whole beam.
UDL resultant: W = w·ℓ = 2·5 = 10 kN, acting at x̄ = 2.5 m
ΣMA = 0: RB·5 = 2·5·2.5
RB = 25/5 = 5 kN
ΣFy = 0: RA = 10 − 5 = 5 kN
Cut at x = 2 m and keep the left part
Only forces left of the cut appear. A UDL portion acts as one force at the middle of that portion.
M = RA·x − (each load left of the cut × its distance to the cut)
Mx = 5·2 − 2·2·1 = 6 kN·m
Answer
Mx = 6 kN·m
10.Shear force & bending moment
Answer: Mmax = 6.75 kN·m
Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut. Maximum moment: since dM/dx = V, the bending moment has its peak where the shear force passes through zero, either at a point load or inside a distributed load.
Support reactions
Equilibrium of the whole beam.
UDL resultant: W = w·ℓ = 6·2 = 12 kN, acting at x̄ = 1 m
ΣMA = 0: RB·4 = 6·2·1
RB = 12/4 = 3 kN
ΣFy = 0: RA = 12 − 3 = 9 kN
Zero shear
The shear force starts at RA, stays constant over any unloaded part and falls with slope w inside the load.
Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.
Split into rectangles
Take the base at full width and the two legs above it (height h − t), so nothing is counted twice.
base: A1 = 260·18 = 4680 mm², y1 = 9 mm
two legs: A2 = 2·18·92 = 3312 mm², y2 = 18 + 92/2 = 64 mm
Centroid
ȳ = (4680·9 + 3312·64)/7992 = 31.79 mm
Answer
ȳ = 31.79 mm
12.Centroid & second moment of area
Answer: σj = 85.88 MPa
Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.
Outer rectangle minus the two side cut-outs
Both cut-outs together are (B − tw) wide and hw = H − 2tf high, and share the axis x.