The A-frame shown stands on a pin at A and a roller at B, 2 m apart. The legs meet at the pin C, 3 m high, and the horizontal tie DE is 0.8 m above the ground. A load of 10 kN acts at C. Find the magnitude of the force C that the pin C exerts on leg BC.
P = 10 kNAB = 2 mheight of C = 3 mheight of DE = 0.8 m
C = kN
8.Frames & machinesHard
The beam AB of the wall bracket shown is pinned at A and propped by the strut CD (C is 1 m below A). The beam carries a uniform load of 1.5 kN/m over its full length and a point load of 4 kN at its free end B. Find the force FCD in the strut.
w = 1.5 kN/mP = 4 kNAD = 0.8 mAB = 2.5 mAC = 1 m
FCD = kN
9.Shear force & bending momentMedium
The beam rests on a pin at A and a roller at B and overhangs B by 1.5 m to the free end C. It carries a point load P1 between the supports and a point load P2 at C. Find the bending moment Mx under the load P1. Use sagging moments positive and upward shear on the left face positive.
L = 9.5 mP1 = 80 kN at 3 mP2 = 10 kN at 9.5 msupports at x = 0 and x = 8 m
Mx = kN·m
10.Shear force & bending momentHard
The simply supported beam carries a uniformly distributed load w over its whole span and a point load P. Find the maximum bending moment Mmax in the beam.
L = 6 mP = 15 kN at 3.5 mw = 4 kN/m from 0 to 6 m
Mmax = kN·m
11.Centroid & second moment of areaMedium
A 150 mm × 300 mm plate has a circular hole of diameter 60 mm on its vertical centre line, with its centre 180 mm above the bottom. Find the second moment of area Ix about the horizontal axis through the centroid.
b = 150 mmh = 300 mmd = 60 mmhole centre: y = 180 mm
Ix = × 10⁶ mm⁴
12.Centroid & second moment of areaHard
A 150 mm × 150 mm plate has a rectangular cut-out 40 mm wide and 40 mm high, centred on the vertical centre line with its centre 60 mm above the bottom. Find the second moment of area Ix about the horizontal axis through the centroid.
b = 150 mmh = 150 mmcut-out: 40 × 40 mmhole centre: y = 60 mm
Ix = × 10⁶ mm⁴
3Solutions
1.Vectors: dot & cross product
Answer: k = −1.25
Dot product:a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.
Dot product equals zero
a·b = 2·2 + 4·k + 1·1 = 0
5 + 4·k = 0
Solve for k
k = −5/4 = −1.25
Answer
k = −1.25
2.Vectors: dot & cross product
Answer: V = 4
Cross product:a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.
Cross product b × c
(b × c)x = bycz − bzcy = (−1)·(−3) − 3·1 = 0
(b × c)y = bzcx − bxcz = 3·(−1) − 0·(−3) = −3
(b × c)z = bxcy − bycx = 0·1 − (−1)·(−1) = −1
Dot product with a
a·(b × c) = 4·0 + 0·(−3) + (−4)·(−1) = 4
V = |4| = 4
Answer
V = 4
3.Beam support reactions
Answer: RA = 8 kN
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.
Free-body diagram
Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.
Equilibrium
Moments about A, counter-clockwise positive. Then vertical force balance.
ΣMA = 0: RB·5 = 10·2.5 + 10·3.5
RB = 60/5 = 12 kN
ΣFy = 0: RA = 20 − 12 = 8 kN
Answer
RA = 8 kN
4.Beam support reactions
Answer: RB = 26.2 kN
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.
Free-body diagram
Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.
Equilibrium
Moments about A, counter-clockwise positive. Then vertical force balance.
UDL resultant: W = w·ℓ = 12·4 = 48 kN, acting at x̄ = 2 m
ΣMA = 0: RB·5 = 10·3.5 + 12·4·2
RB = 131/5 = 26.2 kN
ΣFy = 0: RA = 58 − 26.2 = 31.8 kN
Answer
RB = 26.2 kN
5.Truss: method of joints
Answer: member CG
Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.
Joint C
BC and CD lie on one straight line and the joint carries no load. Balancing forces across that line leaves only CG.
ΣF⊥ = 0 → FCG = 0
Check with the method of joints
Solving all joints gives these member forces (T = tension, C = compression).
Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.
Joint C
BC and CD lie on one straight line and the joint carries no load. Balancing forces across that line leaves only CG.
ΣF⊥ = 0 → FCG = 0
Check with the method of joints
Solving all joints gives these member forces (T = tension, C = compression).
Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.
Tie force from leg BC
By = 5 kN
T = 5·1/2.2 = 2.273 kN
Components of the pin force on BC
Cx = T = 2.273 kN, Cy = −By = −5 kN
Magnitude
C = √(2.273² + 5²) = 5.492 kN
Answer
C = 5.492 kN
8.Frames & machines
Answer: FCD = 23.51 kN
Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.
Resultant of the uniform load
w·L = 1.5·2.5 = 3.75 kN at 1.25 m
Moments about A for the beam
FCD·0.7809·0.8 = 3.75·1.25 + 4·2.5 = 14.69 kN·m
FCD = 23.51 kN
Answer
FCD = 23.51 kN
9.Shear force & bending moment
Answer: Mx = 144.4 kN·m
Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.
Support reactions
Equilibrium of the whole beam. The overhang load also acts about A.
ΣMA = 0: RB·8 = 80·3 + 10·9.5
RB = 335/8 = 41.88 kN
ΣFy = 0: RA = 90 − 41.88 = 48.13 kN
Cut under P1 and keep the left part
Mx = RA·3 = 48.13·3 = 144.4 kN·m
Answer
Mx = 144.4 kN·m
10.Shear force & bending moment
Answer: Mmax = 39.38 kN·m
Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut. Maximum moment: since dM/dx = V, the bending moment has its peak where the shear force passes through zero, either at a point load or inside a distributed load.
Support reactions
Equilibrium of the whole beam.
UDL resultant: W = w·ℓ = 4·6 = 24 kN, acting at x̄ = 3 m
ΣMA = 0: RB·6 = 15·3.5 + 4·6·3
RB = 124.5/6 = 20.75 kN
ΣFy = 0: RA = 39 − 20.75 = 18.25 kN
Where is V = 0?
V(3.5⁻) = RA − w·3.5 = 4.25 kN
V(3.5⁺) = 4.25 − 15 = −10.75 kN
The shear changes sign at the load, so the maximum is under the load.
Sections with holes: treat a hole as a negative area. The centroid is ȳ = (A₁y₁ − A₂y₂)/(A₁ − A₂), with A₁, y₁ for the full plate and A₂, y₂ for the hole. For the second moment of area about the centroidal axis, use the parallel-axis theorem for each part and subtract the hole: I = (Ic1 + A₁d₁²) − (Ic2 + A₂d₂²), where d is the distance from each part's own centroid to the axis through ȳ. A rectangle has Ic = bh³/12 and a circle Ic = πd⁴/64.
Centroid
ȳ = (45000·150 − 2827·180)/(45000 − 2827) = 148 mm
Full plate about ȳ
150·300³/12 + 45000·2.011² = 337.7 × 10⁶ mm⁴
Hole about ȳ
π·60⁴/64 + 2827·32.01² = 3.534 × 10⁶ mm⁴
Subtract
Ix = 334.1 × 10⁶ mm⁴
Answer
Ix = 334.1 × 10⁶ mm⁴
12.Centroid & second moment of area
Answer: Ix = 41.59 × 10⁶ mm⁴
Sections with holes: treat a hole as a negative area. The centroid is ȳ = (A₁y₁ − A₂y₂)/(A₁ − A₂), with A₁, y₁ for the full plate and A₂, y₂ for the hole. For the second moment of area about the centroidal axis, use the parallel-axis theorem for each part and subtract the hole: I = (Ic1 + A₁d₁²) − (Ic2 + A₂d₂²), where d is the distance from each part's own centroid to the axis through ȳ. A rectangle has Ic = bh³/12 and a circle Ic = πd⁴/64.
Centroid
ȳ = (22500·75 − 1600·60)/(22500 − 1600) = 76.15 mm