The frame shown has pins at A, B and C; A and C are fixed to the ground 6 m apart, and B is 2.5 m above the ground and 0.9 m to the right of A. A vertical load of 20 kN acts on member AB at K, 0.54 m (horizontally) from A. Find the force FBC in member BC.
P = 20 kNL = 6 mH = 2.5 mhorizontal distance A to B = 0.9 mhorizontal distance A to K = 0.54 m
FBC = kN
8.Frames & machinesHard
The A-frame shown stands on a pin at A and a roller at B, 4.8 m apart. The legs meet at the pin C, 2.4 m high, and are tied by the horizontal bar DE at 1 m. A horizontal force of 6 kN to the right acts at C. Find the tension T in the tie.
P = 6 kNAB = 4.8 mheight of C = 2.4 mheight of DE = 1 m
T = kN
9.Shear force & bending momentMedium
The simply supported beam carries a clockwise couple M0 = 15 kN·m at x = 2.5 m from A, and no other load. Find the bending moment Mx just to the right of the couple. Use sagging moments positive and upward shear on the left face positive.
L = 5 mM0 = 15 kN·m clockwise, at 2.5 m
Mx = kN·m
10.Shear force & bending momentHard
The simply supported beam carries a uniformly distributed load over part of its span. Find the distance x0 from A to the section where the bending moment is largest.
L = 5 mw = 24 kN/m from 2 to 5 m
x0 = m
11.Centroid & second moment of areaMedium
Find the second moment of area Ix of the T-section about the horizontal axis x through its centroid.
bf = 300 mmtf = 30 mmtw = 14 mmhw = 140 mm
Ix = × 10⁶ mm⁴
12.Centroid & second moment of areaHard
The T-section is used as a beam with the flange on top and carries a sagging bending moment of 15 kN·m. Find the bending stress σbottom at the bottom edge.
Dot product:a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.
Dot product
a·b = (−7)·5 + 3·(−3) + 3·(−5) = −59
Length of b
|b| = √(5² + (−3)² + (−5)²) = 7.681
Scalar projection
compb a = a·b/|b| = −59/7.681 = −7.681
Answer
compb a = −7.681
Negative: a has a component pointing against b.
2.Vectors: dot & cross product
Answer: A = 23.21 m²
Cross product:a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.
Edge vectors
AB = B − A = (−6, 2, 5)
AC = C − A = (1, 5, 4)
Cross product
(AB × AC)x = AByACz − ABzACy = 2·4 − 5·5 = −17
(AB × AC)y = ABzACx − ABxACz = 5·1 − (−6)·4 = 29
(AB × AC)z = ABxACy − AByACx = (−6)·5 − 2·1 = −32
|AB × AC| = √((−17)² + 29² + (−32)²) = 46.41
Area of the triangle
A = ½·46.41 = 23.21 m²
Answer
A = 23.21 m²
3.Beam support reactions
Answer: RA = 53.33 kN
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.
Free-body diagram
Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.
Equilibrium
Moments about A, counter-clockwise positive. Then vertical force balance.
ΣMA = 0: RB·6 = 60·1 + 10·4
RB = 100/6 = 16.67 kN
ΣFy = 0: RA = 70 − 16.67 = 53.33 kN
Answer
RA = 53.33 kN
4.Beam support reactions
Answer: RA = 24.63 kN
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.
Free-body diagram
Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.
Equilibrium
Moments about A, counter-clockwise positive. Then vertical force balance.
UDL resultant: W = w·ℓ = 8·3 = 24 kN, acting at x̄ = 2.5 m
ΣMA = 0: RB·4 = 25·1.5 + 8·3·2.5
RB = 97.5/4 = 24.38 kN
ΣFy = 0: RA = 49 − 24.38 = 24.63 kN
Answer
RA = 24.63 kN
5.Truss: method of joints
Answer: FAC = 4.5 kN
Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.
Support reactions
Equilibrium of the whole truss. Moments about A, counter-clockwise positive.
ΣMA = 0: Cy·5 = 15·3 → Cy = 9 kN
ΣFy = 0: Ay = 15 − 9 = 6 kN
Joint C
The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.
sin γ = 4/4.472 = 0.8944, cos γ = 2/4.472 = 0.4472
Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.
Joint B
AB and BC lie on one straight line and the joint carries no load. Balancing forces across that line leaves only BF.
ΣF⊥ = 0 → FBF = 0
Check with the method of joints
Solving all joints gives these member forces (T = tension, C = compression).
Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.
Two-force member BC
BC = √(5.1² + 2.5²) = 5.68 m
Whole frame: moments about A
The ground pushes on BC at C along CB; its horizontal component passes through A, only the vertical one has a moment.
FBC·(2.5/5.68)·6 = 20·0.54
FBC = 4.089 kN (compression)
Answer
FBC = 4.089 kN
8.Frames & machines
Answer: T = 5.143 kN
Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.
Whole frame: moments about A
By·4.8 = 6·2.4
By = 3 kN
Leg BC: moments about C
3·2.4 = T·1.4
T = 5.143 kN
Answer
T = 5.143 kN
A positive T means the tie is in tension, as assumed.
9.Shear force & bending moment
Answer: Mx = 7.5 kN·m
Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut. An applied couple makes the bending moment diagram jump by the size of the couple.
Support reactions
Moments about A, counter-clockwise positive: RB·L − M0 = 0. Vertical balance: RA + RB = 0.
RB = M0/L = 15/5 = 3 kN (upward)
RA = −RB = −3 kN (downward)
Cut just right of the couple
The left part now contains RA and the couple.
Mx = RA·a + M0 = −3·2.5 + 15 = 7.5 kN·m
Answer
Mx = 7.5 kN·m
10.Shear force & bending moment
Answer: x0 = 2.9 m
Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut. Maximum moment: since dM/dx = V, the bending moment has its peak where the shear force passes through zero, either at a point load or inside a distributed load.
Support reactions
Equilibrium of the whole beam.
UDL resultant: W = w·ℓ = 24·3 = 72 kN, acting at x̄ = 3.5 m
ΣMA = 0: RB·5 = 24·3·3.5
RB = 252/5 = 50.4 kN
ΣFy = 0: RA = 72 − 50.4 = 21.6 kN
Zero shear
The shear force starts at RA, stays constant over any unloaded part and falls with slope w inside the load.
RA − w·(x0 − 2) = 0
x0 = 2 + 21.6/24 = 2.9 m
Answer
x0 = 2.9 m
11.Centroid & second moment of area
Answer: Ix = 15.5 × 10⁶ mm⁴
Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.
Split into two rectangles
Measure every y from the bottom edge.
flange: Af = 300·30 = 9000 mm², yf = 140 + 30/2 = 155 mm
Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.
Split into two rectangles
Measure every y from the bottom edge.
flange: Af = 140·10 = 1400 mm², yf = 160 + 10/2 = 165 mm