Statics: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Vectors: dot & cross product

Magnitude
|a| = √(ax² + ay² + az²)
Unit vector
û = a/|a|
Components from an angle
Fx = F·cos θ, Fy = F·sin θ
Dot product
a·b = axbx + ayby + azbz = |a||b|cos θ
Scalar projection of a onto b
a·b/|b|
Work
W = F·d
Cross product
a × b = (aybz − azby, azbx − axbz, axby − aybx)
Areas
parallelogram |a × b|, triangle ½|a × b|
Moment about O
MO = r × F, r = A − O
Volume of a parallelepiped
V = |a·(b × c)|

Method

  1. Write every vector in components; for a force given by a magnitude and an angle, use F·cos θ and F·sin θ.
  2. For lengths and directions use the magnitude √(x² + y² + z²) and the unit vector a/|a|.
  3. Use the dot product for angles, projections, perpendicularity and work: a·b = |a||b|cos θ.
  4. Use the cross product for perpendicular vectors, areas and moments: write the three components carefully, keeping the order a × b.

Beam support reactions

Equilibrium
ΣFx = 0, ΣFy = 0, ΣM = 0
Uniform load
resultant w·L at the middle of the load
Moment
M = F·d

Method

  1. Draw a free-body diagram and replace each support by its reactions.
  2. Replace every distributed load by a single force at its centroid.
  3. Take moments about one support to find the reaction at the other.
  4. Use ΣFy = 0 to find the remaining reaction, and check with a second moment equation.

Truss: method of joints

Method of joints
ΣFx = 0, ΣFy = 0 at each joint
Method of sections
ΣM = 0 about a cut point
Member force
positive = tension, negative = compression

Method

  1. Find the support reactions for the whole truss.
  2. Method of joints: start at a joint with at most two unknown member forces and use ΣFx = 0 and ΣFy = 0.
  3. Method of sections: cut through the member you need and take moments about a point where the other unknown members meet.
  4. Assume tension; a negative answer means compression.

Frames & machines

Equilibrium of each member
ΣFx = 0, ΣFy = 0, ΣM = 0
Two-force member
force along the line through its two pins
Pin force
equal and opposite on the two members it joins
Magnitude of a pin force
F = √(Fx² + Fy²)
Lever, pliers, bell crank
Fin·a = Fout·b
Toggle
Flink = F/(2 sin θ), Q = F/(2 tan θ)
Uniform load
resultant w·L at the middle of the load

Method

  1. Draw the whole structure and find the support reactions if there are no more than three unknowns.
  2. Spot the two-force members: loaded only at two pins, their force acts along the line between the pins.
  3. Take the frame apart and draw every member on its own, with equal and opposite pin forces where members meet.
  4. For each member, take moments about a pin with unknown forces, then use ΣFx = 0 and ΣFy = 0; combine components into a magnitude at the end.

Shear force & bending moment

Shear and moment
V = ΣF on one side, M = ΣF·d on one side
Bending stress
σ = M·y/I
Rectangle
I = bh³/12
Section modulus
W = I/ymax
Simply supported, uniform load
Mmax = wL²/8

Method

  1. Find the support reactions from equilibrium of the whole beam.
  2. Cut the beam at the section you need and keep one side.
  3. Shear force: sum of the vertical forces on that side. Bending moment: sum of their moments about the cut.
  4. For the maximum moment, find where the shear force is zero.

Centroid & second moment of area

Centroid
ȳ = ΣAiyi/ΣAi
Rectangle
I = bh³/12
Parallel-axis theorem
I = Ic + A·d²
Composite section
I = Σ(Ic,i + Aidi²)

2Practice problems

1.Vectors: dot & cross productMedium
xyzab

Find the scalar projection compb a of a = (2, 6, −4) onto b = (6, 1, −4), that is, the component of a in the direction of b.

a = (2, 6, −4)b = (6, 1, −4)
compb a =
2.Vectors: dot & cross productHard
xyzab

The unit vector n̂ is perpendicular to both a = (3, 0, −2) and b = (0, 3, 5) and has a positive z-component. Find its x-component n̂x.

a = (3, 0, −2)b = (0, 3, 5)n̂z > 0
n̂x =
3.Beam support reactionsMedium
w = 3 kN/mP = 25 kNABMA​ = ?4 m2 m

The cantilever beam is fixed to the wall at A. It carries a uniformly distributed load w along its whole length and a point load P at 4 m from the wall. Find the magnitude of the reaction moment MA at the wall.

L = 6 mP = 25 kN at 4 mw = 3 kN/m from 0 to 6 m
MA = kN·m
4.Beam support reactionsHard
w = 2 kN/mP = 20 kNABCRA​ = ?2.5 m0.5 m1 m2 m

The beam has a pin at A and a roller at B, 4 m from A, and overhangs B to the free end C. It carries a point load P at 2.5 m from A and a uniformly distributed load w from 3 m to the free end at 6 m. Find the vertical reaction RA, taking upward as positive.

AB = 4 mAC = 6 mP = 20 kN at 2.5 mw = 2 kN/m from 3 to 6 m
RA = kN
5.Truss: method of jointsMedium
ABCDEFGH15 kN20 kN30 kN4 × 3 m4 m

Exactly one member of this truss carries no force under these loads. Which is the zero-force member? Click it in the diagram.

B: 15 kN ↓D: 20 kN ↓H: 30 kN ↓
  1. 1member AB
  2. 2member BC
  3. 3member CD
  4. 4member DE
  5. 5member FG
  6. 6member GH
  7. 7member AF
  8. 8member HE
  9. 9member BF
  10. 10member CG
  11. 11member DH
  12. 12member FC
  13. 13member HC
6.Truss: method of jointsHard
ABBCACACB55 kN25 kN5 m1 m4 m

Use the method of joints to find the force FBC in member BC. Give tension as positive and compression as negative.

span = 5 mheight = 4 mB is 1 m from Avertical load = 55 kNhorizontal load = 25 kN ←
FBC = kN
7.Frames & machinesMedium
OAB100 NQ150 mm120 mmFO​ = ?

The bell crank shown turns about the pin O. A vertical force of 100 N at A (150 mm from O) is balanced by a horizontal force at B (120 mm above O). Find the magnitude of the pin reaction FO.

F = 100 NOA = 150 mmOB = 120 mm
FO = N
8.Frames & machinesHard
2 kN4 m1.2 m0.8 m0.5 mABCDEK

The A-frame shown stands on a pin at A and a roller at B, 4 m apart, with its apex pin C 2 m high and the horizontal tie DE 1.2 m above the ground. A vertical load of 2 kN acts on leg AC at K, 0.5 m (horizontally) from A. Find the magnitude of the force C that the pin C exerts on leg BC.

P = 2 kNAB = 4 mheight of C = 2 mheight of DE = 1.2 mhorizontal distance A to K = 0.5 m
C = kN
9.Shear force & bending momentMedium
P1​ = 25 kNP2​ = 65 kNAB4 m1 m5 m

The simply supported beam carries two point loads. Find the maximum bending moment Mmax in the beam.

L = 10 mP1 = 25 kN at 4 mP2 = 65 kN at 5 m
Mmax = kN·m
10.Shear force & bending momentHard
w = 12 kN/mP = 10 kNABsection8 m2 m

Find the bending moment Mx at the section x = 8 m from support A. Use sagging moments positive and upward shear on the left face positive.

L = 10 mP = 10 kN at 8 mw = 12 kN/m from 0 to 10 mx = 8 m
Mx = kN·m
11.Centroid & second moment of areaMedium
xD = 270d = 238dimensions in mm

A circular tube has outside diameter D = 270 mm and inside diameter d = 238 mm. Find its radius of gyration r about the horizontal centroidal axis.

D = 270 mmd = 238 mm
r = mm
12.Centroid & second moment of areaHard
2601028010xM = 40 kN·mdimensions in mm

The T-section is used as a beam with the flange on top and carries a sagging bending moment of 40 kN·m. Find the bending stress σbottom at the bottom edge.

bf = 260 mmtf = 10 mmtw = 10 mmhw = 280 mmM = 40 kN·m
σbottom = MPa

3Solutions

1.Vectors: dot & cross product

Answer: compb a = 4.67

Dot product: a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.

Dot product

a·b = 2·6 + 6·1 + (−4)·(−4) = 34

Length of b

|b| = √(6² + 1² + (−4)²) = 7.28

Scalar projection

compb a = a·b/|b| = 34/7.28 = 4.67

Answer

compb a = 4.67
2.Vectors: dot & cross product

Answer: n̂x = 0.3244

Cross product: a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.

Cross product

(a × b)x = aybz − azby = 0·5 − (−2)·3 = 6
(a × b)y = azbx − axbz = (−2)·0 − 3·5 = −15
(a × b)z = axby − aybx = 3·3 − 0·0 = 9

Normalise

The z-component of a × b is already positive.

|a × b| = √(6² + (−15)² + 9²) = 18.49
n̂ = (6, −15, 9)/18.49 = (0.3244, −0.8111, 0.4867)
n̂x = 0.3244

Answer

n̂x = 0.3244
3.Beam support reactions

Answer: MA = 154 kN·m

Cantilever equilibrium: a fixed support can push up and also resist rotation, so it gives a vertical reaction RA and a reaction moment MA. ΣFy = 0 gives RA, and moments about the wall give MA = Σ(load × distance from the wall). A distributed load acts as its resultant at the centroid of the load diagram.

Resultant of the distributed load

W = 3·6 = 18 kN, x̄ = 3 m

Moment about the wall

MA = P·a + W·x̄ = 25·4 + 18·3 = 154 kN·m

Answer

MA = 154 kN·m
4.Beam support reactions

Answer: RA = 6.75 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Replace each distributed load by its resultant (its area) acting at the centroid of the load diagram, and take moments about a support to remove that support’s reaction from the equation.

Resultant of the distributed load

W = 2·3 = 6 kN, x̄ = (3 + 6)/2 = 4.5 m

Equilibrium

Moments about A, counter-clockwise positive. Then vertical force balance.

ΣMA = 0: RB·4 = 20·2.5 + 6·4.5
RB = 77/4 = 19.25 kN
RA = 26 − 19.25 = 6.75 kN

Answer

RA = 6.75 kN
5.Truss: method of joints

Answer: member CG

Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.

Joint G

FG and GH lie on one straight line and the joint carries no load. Balancing forces across that line leaves only CG.

ΣF⊥ = 0 → FCG = 0

Check with the method of joints

Solving all joints gives these member forces (T = tension, C = compression).

AB: 17.81 kN (T), BC: 17.81 kN (T), CD: 30.94 kN (T), DE: 30.94 kN (T), FG: 24.38 kN (C), GH: 24.38 kN (C), AF: 29.69 kN (C), HE: 51.56 kN (C), BF: 15 kN (T), CG: 0, DH: 20 kN (T), FC: 10.94 kN (T), HC: 10.94 kN (C)

Answer

Zero-force member: CG
6.Truss: method of joints

Answer: FBC = 12.73 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB55 kN25 kNAy​Cy​Ax​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·5 = 55·1 − 25·4 → Cy = −9 kN
ΣFy = 0: Ay = 55 − −9 = 64 kN
ΣFx = 0: Ax = 25 kN

Joint C

The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.

sin γ = 4/5.657 = 0.7071, cos γ = 4/5.657 = 0.7071
ΣFy = 0: Cy + FBC·sin γ = 0 → FBC = −−9/0.7071 = 12.73 kN

Answer

FBC = 12.73 kN (tension)
7.Frames & machines

Answer: FO = 160.1 N

Machines: pliers, levers, linkages and clamps turn an input force into a larger or a differently directed output force. Draw one part as a free body and take moments about its pivot: the pin force drops out, and Fin·a = Fout·b gives the mechanical advantage a/b. The pin force then follows from ΣF = 0 on the same part. In a toggle, two links meet at a shallow angle θ; each link is a two-force member, so a small force F at the joint creates large link forces F/(2 sin θ) and a clamping force F/(2 tan θ).

Force at B

Q = 100·150/120 = 125 N

Pin reaction

Ox = 125 N, Oy = 100 N
FO = √(125² + 100²) = 160.1 N

Answer

FO = 160.1 N
8.Frames & machines

Answer: C = 0.6731 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Support reaction at B

By = 2·0.5/4 = 0.25 kN

Tie force

T = 0.25·2/0.8 = 0.625 kN

Pin force on BC

Cx = 0.625 kN, Cy = −0.25 kN
C = √(0.625² + 0.25²) = 0.6731 kN

Answer

C = 0.6731 kN
9.Shear force & bending moment

Answer: Mmax = 212.5 kN·m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut. Maximum moment: since dM/dx = V, the bending moment has its peak where the shear force passes through zero, either at a point load or inside a distributed load.

Support reactions

Equilibrium of the whole beam.

ΣMA = 0: RB·10 = 25·4 + 65·5
RB = 425/10 = 42.5 kN
ΣFy = 0: RA = 90 − 42.5 = 47.5 kN

Moment under each load

Keep the part left of each load.

under P1: M = RA·4 = 47.5·4 = 190 kN·m
under P2: M = RB·5 = 42.5·5 = 212.5 kN·m

Largest value

Mmax = 212.5 kN·m (under P2)

Answer

Mmax = 212.5 kN·m
10.Shear force & bending moment

Answer: Mx = 112 kN·m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.

Support reactions

Equilibrium of the whole beam.

UDL resultant: W = w·ℓ = 12·10 = 120 kN, acting at x̄ = 5 m
ΣMA = 0: RB·10 = 10·8 + 12·10·5
RB = 680/10 = 68 kN
ΣFy = 0: RA = 130 − 68 = 62 kN
w = 12 kN/mP = 10 kNABRA​ = 62RB​ = 68section8 m2 m

Cut at x = 8 m and keep the left part

Only forces left of the cut appear. A UDL portion acts as one force at the middle of that portion.

M = RA·x − (each load left of the cut × its distance to the cut)
Mx = 62·8 − 12·8·4 = 112 kN·m

Answer

Mx = 112 kN·m
11.Centroid & second moment of area

Answer: r = 89.98 mm

Second moment of area: for a rectangle about its own centroidal axis I = bh³/12, and about its base bh³/3 (parallel-axis theorem I = Ic + A·d²). A hole is handled by subtracting its I, as long as both parts share the same axis. The elastic section modulus is S = I/c, where c is the distance to the extreme fibre. The radius of gyration r = √(I/A) is the distance at which the whole area would give the same I; it is used in column buckling.

Net area and second moment of area

A = π(D² − d²)/4 = 12767 mm²
I = π(D⁴ − d⁴)/64 = 1.034 × 10⁸ mm⁴

Radius of gyration

r = √(I/A) = √(1.034 × 10⁸/12767) = 89.98 mm

Answer

r = 89.98 mm
12.Centroid & second moment of area

Answer: σbottom = 179.9 MPa

Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.

Split into two rectangles

Measure every y from the bottom edge.

flange: Af = 260·10 = 2600 mm², yf = 280 + 10/2 = 285 mm
web: Aw = 10·280 = 2800 mm², yw = 280/2 = 140 mm

Centroid

ȳ = (Afyf + Awyw)/(Af + Aw) = (2600·285 + 2800·140)/5400 = 209.8 mm

Parallel-axis theorem

flange: 260·10³/12 + 2600·(285 − 209.8)² = 1.472 × 10⁷ mm⁴
web: 10·280³/12 + 2800·(140 − 209.8)² = 3.194 × 10⁷ mm⁴
Ix = 1.472 × 10⁷ + 3.194 × 10⁷ = 4.666 × 10⁷ mm⁴

Bending stress

The bottom edge is ȳ from the axis.

y = 209.8 mm
σ = M·y/I = 4 × 10⁷·209.8/4.666 × 10⁷ = 179.9 MPa

Answer

σbottom = 179.9 MPa

ExamProblems · examproblems.com/courses/statics