Statics: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Vectors: dot & cross product

Magnitude
|a| = √(ax² + ay² + az²)
Unit vector
û = a/|a|
Components from an angle
Fx = F·cos θ, Fy = F·sin θ
Dot product
a·b = axbx + ayby + azbz = |a||b|cos θ
Scalar projection of a onto b
a·b/|b|
Work
W = F·d
Cross product
a × b = (aybz − azby, azbx − axbz, axby − aybx)
Areas
parallelogram |a × b|, triangle ½|a × b|
Moment about O
MO = r × F, r = A − O
Volume of a parallelepiped
V = |a·(b × c)|

Method

  1. Write every vector in components; for a force given by a magnitude and an angle, use F·cos θ and F·sin θ.
  2. For lengths and directions use the magnitude √(x² + y² + z²) and the unit vector a/|a|.
  3. Use the dot product for angles, projections, perpendicularity and work: a·b = |a||b|cos θ.
  4. Use the cross product for perpendicular vectors, areas and moments: write the three components carefully, keeping the order a × b.

Beam support reactions

Equilibrium
ΣFx = 0, ΣFy = 0, ΣM = 0
Uniform load
resultant w·L at the middle of the load
Moment
M = F·d

Method

  1. Draw a free-body diagram and replace each support by its reactions.
  2. Replace every distributed load by a single force at its centroid.
  3. Take moments about one support to find the reaction at the other.
  4. Use ΣFy = 0 to find the remaining reaction, and check with a second moment equation.

Truss: method of joints

Method of joints
ΣFx = 0, ΣFy = 0 at each joint
Method of sections
ΣM = 0 about a cut point
Member force
positive = tension, negative = compression

Method

  1. Find the support reactions for the whole truss.
  2. Method of joints: start at a joint with at most two unknown member forces and use ΣFx = 0 and ΣFy = 0.
  3. Method of sections: cut through the member you need and take moments about a point where the other unknown members meet.
  4. Assume tension; a negative answer means compression.

Frames & machines

Equilibrium of each member
ΣFx = 0, ΣFy = 0, ΣM = 0
Two-force member
force along the line through its two pins
Pin force
equal and opposite on the two members it joins
Magnitude of a pin force
F = √(Fx² + Fy²)
Lever, pliers, bell crank
Fin·a = Fout·b
Toggle
Flink = F/(2 sin θ), Q = F/(2 tan θ)
Uniform load
resultant w·L at the middle of the load

Method

  1. Draw the whole structure and find the support reactions if there are no more than three unknowns.
  2. Spot the two-force members: loaded only at two pins, their force acts along the line between the pins.
  3. Take the frame apart and draw every member on its own, with equal and opposite pin forces where members meet.
  4. For each member, take moments about a pin with unknown forces, then use ΣFx = 0 and ΣFy = 0; combine components into a magnitude at the end.

Shear force & bending moment

Shear and moment
V = ΣF on one side, M = ΣF·d on one side
Bending stress
σ = M·y/I
Rectangle
I = bh³/12
Section modulus
W = I/ymax
Simply supported, uniform load
Mmax = wL²/8

Method

  1. Find the support reactions from equilibrium of the whole beam.
  2. Cut the beam at the section you need and keep one side.
  3. Shear force: sum of the vertical forces on that side. Bending moment: sum of their moments about the cut.
  4. For the maximum moment, find where the shear force is zero.

Centroid & second moment of area

Centroid
ȳ = ΣAiyi/ΣAi
Rectangle
I = bh³/12
Parallel-axis theorem
I = Ic + A·d²
Composite section
I = Σ(Ic,i + Aidi²)

2Practice problems

1.Vectors: dot & cross productMedium
xyzab

Find the angle θ between the vectors a = (6, −1, 4) and b = (−3, −6, −6), in degrees.

a = (6, −1, 4)b = (−3, −6, −6)
θ = °
2.Vectors: dot & cross productHard
xyzabc

Find the volume V of the parallelepiped whose edges from one corner are a = (−1, 5, −1), b = (2, 0, 4) and c = (−4, 4, 3).

a = (−1, 5, −1)b = (2, 0, 4)c = (−4, 4, 3)
V =
3.Beam support reactionsMedium
w = 10 kN/mP = 75 kNABMA​ = ?1.5 m0.5 m2 m

The cantilever beam is fixed to the wall at A. It carries a uniformly distributed load w from the wall to 2 m and a point load P at 1.5 m from the wall. Find the magnitude of the reaction moment MA at the wall.

L = 4 mP = 75 kN at 1.5 mw = 10 kN/m from 0 to 2 m
MA = kN·m
4.Beam support reactionsHard
w = 12 kN/mP = 20 kNABRA​ = ?RB​2 m2 m1 m

The simply supported beam has a pin at A and a roller at B. Find the vertical support reaction RA.

L = 5 mP = 20 kN at 4 mw = 12 kN/m from 2 to 5 m
RA = kN
5.Truss: method of jointsMedium
ABBCACACB40 kN4 m3 m3 m

Use the method of joints to find the force FAB in member AB. Give tension as positive and compression as negative.

span = 4 mheight = 3 mB is 3 m from Avertical load = 40 kN
FAB = kN
6.Truss: method of jointsHard
ABBCACACB55 kN15 kN6 m2 m3 m

Use the method of joints to find the force FAC in member AC. Give tension as positive and compression as negative.

span = 6 mheight = 3 mB is 2 m from Avertical load = 55 kNhorizontal load = 15 kN ←
FAC = kN
7.Frames & machinesMedium
8 kN6 m3 m3.6 mABCK

The frame shown has pins at A, B and C; A and C are fixed to the ground 6 m apart, and B is 3 m above the ground and 3.6 m to the right of A. A vertical load of 8 kN acts on member AB at K, 1.8 m (horizontally) from A. Find the force FBC in member BC.

P = 8 kNL = 6 mH = 3 mhorizontal distance A to B = 3.6 mhorizontal distance A to K = 1.8 m
FBC = kN
8.Frames & machinesHard
w = 1 kN/m15 kN1.5 m1.5 m0.8 mABCD

The beam AB of the wall bracket shown is pinned at A and propped by the strut CD (C is 0.8 m below A). The beam carries a uniform load of 1 kN/m over its full length and a point load of 15 kN at its free end B. Find the force FCD in the strut.

w = 1 kN/mP = 15 kNAD = 1.5 mAB = 3 mAC = 0.8 m
FCD = kN
9.Shear force & bending momentMedium
w = 5 kN/mABsection3 m1 m

Find the bending moment Mx at the section x = 3 m from support A. Use sagging moments positive and upward shear on the left face positive.

L = 4 mw = 5 kN/m from 0 to 4 mx = 3 m
Mx = kN·m
10.Shear force & bending momentHard
w = 12 kN/mP = 60 kNABsection4 m2 m

Find the bending moment Mx at the section x = 4 m from support A. Use sagging moments positive and upward shear on the left face positive.

L = 6 mP = 60 kN at 4 mw = 12 kN/m from 0 to 6 mx = 4 m
Mx = kN·m
11.Centroid & second moment of areaMedium
2201522016xdimensions in mm

Find the second moment of area Ix of the T-section about the horizontal axis x through its centroid.

bf = 220 mmtf = 15 mmtw = 16 mmhw = 220 mm
Ix = × 10⁶ mm⁴
12.Centroid & second moment of areaHard
110220242601814xdimensions in mm

A welded I-section has a top flange 110 × 24 mm, a web 260 mm high and 14 mm thick, and a bottom flange 220 × 18 mm (width × thickness). Find its second moment of area Ix about the horizontal axis x through its centroid.

top flange: 110 × 24 mmweb: 14 × 260 mmbottom flange: 220 × 18 mm
Ix = × 10⁶ mm⁴

3Solutions

1.Vectors: dot & cross product

Answer: θ = 123.3 °

Dot product: a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.

Dot product

a·b = 6·(−3) + (−1)·(−6) + 4·(−6) = −36

Magnitudes

|a| = √(6² + (−1)² + 4²) = 7.28
|b| = √((−3)² + (−6)² + (−6)²) = 9

Angle

cos θ = −36/(7.28·9) = −0.5494
θ = arccos(−0.5494) = 123.3°

Answer

θ = 123.3°
2.Vectors: dot & cross product

Answer: V = 102

Cross product: a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.

Cross product b × c

(b × c)x = bycz − bzcy = 0·3 − 4·4 = −16
(b × c)y = bzcx − bxcz = 4·(−4) − 2·3 = −22
(b × c)z = bxcy − bycx = 2·4 − 0·(−4) = 8

Dot product with a

a·(b × c) = (−1)·(−16) + 5·(−22) + (−1)·8 = −102
V = |−102| = 102

Answer

V = 102
3.Beam support reactions

Answer: MA = 132.5 kN·m

Cantilever equilibrium: a fixed support can push up and also resist rotation, so it gives a vertical reaction RA and a reaction moment MA. ΣFy = 0 gives RA, and moments about the wall give MA = Σ(load × distance from the wall). A distributed load acts as its resultant at the centroid of the load diagram.

Resultant of the distributed load

W = 10·2 = 20 kN, x̄ = 1 m

Moment about the wall

MA = P·a + W·x̄ = 75·1.5 + 20·1 = 132.5 kN·m

Answer

MA = 132.5 kN·m
4.Beam support reactions

Answer: RA = 14.8 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.

w = 12 kN/mP = 20 kNABRA​RB​2 m2 m1 m

Free-body diagram

Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.

Equilibrium

Moments about A, counter-clockwise positive. Then vertical force balance.

UDL resultant: W = w·ℓ = 12·3 = 36 kN, acting at x̄ = 3.5 m
ΣMA = 0: RB·5 = 20·4 + 12·3·3.5
RB = 206/5 = 41.2 kN
ΣFy = 0: RA = 56 − 41.2 = 14.8 kN

Answer

RA = 14.8 kN
5.Truss: method of joints

Answer: FAB = −14.14 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB40 kNAy​Cy​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·4 = 40·3 → Cy = 30 kN
ΣFy = 0: Ay = 40 − 30 = 10 kN

Joint A

Assume every member is in tension (pulling away from the joint). Only AB has a vertical component at A.

sin α = 3/4.243 = 0.7071
ΣFy = 0: Ay + FAB·sin α = 0
FAB = −10/0.7071 = −14.14 kN

Answer

FAB = −14.14 kN (compression)
6.Truss: method of joints

Answer: FAC = 14.44 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB55 kN15 kNAy​Cy​Ax​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·6 = 55·2 − 15·3 → Cy = 10.83 kN
ΣFy = 0: Ay = 55 − 10.83 = 44.17 kN
ΣFx = 0: Ax = 15 kN

Joint C

The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.

sin γ = 3/5 = 0.6, cos γ = 4/5 = 0.8
ΣFy = 0: Cy + FBC·sin γ = 0 → FBC = −10.83/0.6 = −18.06 kN
ΣFx = 0: −FAC − FBC·cos γ = 0 → FAC = −(−18.06)·0.8 = 14.44 kN

Answer

FAC = 14.44 kN (tension)
7.Frames & machines

Answer: FBC = 3.073 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Two-force member BC

BC = √(2.4² + 3²) = 3.842 m

Whole frame: moments about A

The ground pushes on BC at C along CB; its horizontal component passes through A, only the vertical one has a moment.

FBC·(3/3.842)·6 = 8·1.8
FBC = 3.073 kN (compression)

Answer

FBC = 3.073 kN
8.Frames & machines

Answer: FCD = 70.13 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Resultant of the uniform load

w·L = 1·3 = 3 kN at 1.5 m

Moments about A for the beam

FCD·0.4706·1.5 = 3·1.5 + 15·3 = 49.5 kN·m
FCD = 70.13 kN

Answer

FCD = 70.13 kN
9.Shear force & bending moment

Answer: Mx = 7.5 kN·m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.

Support reactions

Equilibrium of the whole beam.

UDL resultant: W = w·ℓ = 5·4 = 20 kN, acting at x̄ = 2 m
ΣMA = 0: RB·4 = 5·4·2
RB = 40/4 = 10 kN
ΣFy = 0: RA = 20 − 10 = 10 kN
w = 5 kN/mABRA​ = 10RB​ = 10section3 m1 m

Cut at x = 3 m and keep the left part

Only forces left of the cut appear. A UDL portion acts as one force at the middle of that portion.

M = RA·x − (each load left of the cut × its distance to the cut)
Mx = 10·3 − 5·3·1.5 = 7.5 kN·m

Answer

Mx = 7.5 kN·m
10.Shear force & bending moment

Answer: Mx = 128 kN·m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.

Support reactions

Equilibrium of the whole beam.

UDL resultant: W = w·ℓ = 12·6 = 72 kN, acting at x̄ = 3 m
ΣMA = 0: RB·6 = 60·4 + 12·6·3
RB = 456/6 = 76 kN
ΣFy = 0: RA = 132 − 76 = 56 kN
w = 12 kN/mP = 60 kNABRA​ = 56RB​ = 76section4 m2 m

Cut at x = 4 m and keep the left part

Only forces left of the cut appear. A UDL portion acts as one force at the middle of that portion.

M = RA·x − (each load left of the cut × its distance to the cut)
Mx = 56·4 − 12·4·2 = 128 kN·m

Answer

Mx = 128 kN·m
11.Centroid & second moment of area

Answer: Ix = 37.77 × 10⁶ mm⁴

Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.

Split into two rectangles

Measure every y from the bottom edge.

flange: Af = 220·15 = 3300 mm², yf = 220 + 15/2 = 227.5 mm
web: Aw = 16·220 = 3520 mm², yw = 220/2 = 110 mm

Centroid

ȳ = (Afyf + Awyw)/(Af + Aw) = (3300·227.5 + 3520·110)/6820 = 166.9 mm

Parallel-axis theorem

flange: 220·15³/12 + 3300·(227.5 − 166.9)² = 1.22 × 10⁷ mm⁴
web: 16·220³/12 + 3520·(110 − 166.9)² = 2.558 × 10⁷ mm⁴
Ix = 1.22 × 10⁷ + 2.558 × 10⁷ = 3.777 × 10⁷ mm⁴ = 37.77 × 10⁶ mm⁴

Answer

Ix = 37.77 × 10⁶ mm⁴
12.Centroid & second moment of area

Answer: Ix = 147.5 × 10⁶ mm⁴

Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.

Split into three rectangles

Measure every y from the bottom edge.

top flange: A = 2640 mm², y = 290 mm
web: A = 3640 mm², y = 148 mm
bottom flange: A = 3960 mm², y = 9 mm

Centroid

ȳ = (2640·290 + 3640·148 + 3960·9)/10240 = 130.9 mm

Parallel-axis theorem

top flange: 110·24³/12 + 2640·159.1² = 6.699 × 10⁷ mm⁴
web: 14·260³/12 + 3640·17.14² = 2.158 × 10⁷ mm⁴
bottom flange: 220·18³/12 + 3960·121.9² = 5.891 × 10⁷ mm⁴
Ix = 6.699 × 10⁷ + 2.158 × 10⁷ + 5.891 × 10⁷
Ix = 1.475 × 10⁸ mm⁴ = 147.5 × 10⁶ mm⁴

Answer

Ix = 147.5 × 10⁶ mm⁴

ExamProblems · examproblems.com/courses/statics