Exactly one member of this truss carries no force under these loads. Which is the zero-force member? Click it in the diagram.
B: 25 kN ↓D: 20 kN ↓F: 10 kN →H: 35 kN ↓
1member AB
2member BC
3member CD
4member DE
5member FG
6member GH
7member AF
8member HE
9member BF
10member CG
11member DH
12member FC
13member HC
7.Frames & machinesMedium
The A-frame shown stands on a pin at A and a roller at B, 2.4 m apart, with its apex pin C 2 m high and the horizontal tie DE 0.6 m above the ground. A vertical load of 12 kN acts on leg AC at K, 0.9 m (horizontally) from A. Find the tension T in the tie.
P = 12 kNAB = 2.4 mheight of C = 2 mheight of DE = 0.6 mhorizontal distance A to K = 0.9 m
T = kN
8.Frames & machinesHard
The A-frame shown stands on a pin at A and a roller at B, 4 m apart, with its apex pin C 4.5 m high and the horizontal tie DE 1 m above the ground. A vertical load of 4 kN acts on leg AC at K, 1 m (horizontally) from A. Find the magnitude of the force C that the pin C exerts on leg BC.
P = 4 kNAB = 4 mheight of C = 4.5 mheight of DE = 1 mhorizontal distance A to K = 1 m
C = kN
9.Shear force & bending momentMedium
The marks A to G split the beam into six equal parts. At which mark is the bending moment largest in size, sagging or hogging? Click it in the diagram.
35 kN @ 3 m4 kN/m, 0–5 m
1A (x = 0 m)
2B (x = 1 m)
3C (x = 2 m)
4D (x = 3 m)
5E (x = 4 m)
6F (x = 5 m)
7G (x = 6 m)
10.Shear force & bending momentHard
Find the bending moment Mx at the section x = 1.5 m from support A. Use sagging moments positive and upward shear on the left face positive.
L = 5 mP = 20 kN at 1.5 mw = 4 kN/m from 0 to 5 mx = 1.5 m
Mx = kN·m
11.Centroid & second moment of areaMedium
A 200 mm × 240 mm plate has a circular hole of diameter 50 mm on its vertical centre line, with its centre 72 mm above the bottom. Find the second moment of area Ix about the horizontal axis through the centroid.
b = 200 mmh = 240 mmd = 50 mmhole centre: y = 72 mm
Ix = × 10⁶ mm⁴
12.Centroid & second moment of areaHard
The T-section is used as a beam with the flange on top and carries a sagging bending moment of 5 kN·m. Find the bending stress σbottom at the bottom edge.
Dot product:a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.
Positive: the angle between the vectors is less than 90°.
2.Vectors: dot & cross product
Answer: V = 50
Cross product:a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.
Cross product b × c
(b × c)x = bycz − bzcy = (−2)·2 − 5·0 = −4
(b × c)y = bzcx − bxcz = 5·(−2) − 2·2 = −14
(b × c)z = bxcy − bycx = 2·0 − (−2)·(−2) = −4
Dot product with a
a·(b × c) = 4·(−4) + (−5)·(−14) + 1·(−4) = 50
V = |50| = 50
Answer
V = 50
3.Beam support reactions
Answer: RA = 25.42 kN
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.
Free-body diagram
Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.
Equilibrium
Moments about A, counter-clockwise positive. Then vertical force balance.
ΣMA = 0: RB·6 = 35·2.5 + 20·4.5
RB = 177.5/6 = 29.58 kN
ΣFy = 0: RA = 55 − 29.58 = 25.42 kN
Answer
RA = 25.42 kN
4.Beam support reactions
Answer: RA = 50.3 kN
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.
Free-body diagram
Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.
Equilibrium
Moments about A, counter-clockwise positive. Then vertical force balance.
UDL resultant: W = w·ℓ = 4·2 = 8 kN, acting at x̄ = 9 m
ΣMA = 0: RB·10 = 55·1 + 4·2·9
RB = 127/10 = 12.7 kN
ΣFy = 0: RA = 63 − 12.7 = 50.3 kN
Answer
RA = 50.3 kN
5.Truss: method of joints
Answer: member DH
Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.
Joint D
CD and DE lie on one straight line and the joint carries no load. Balancing forces across that line leaves only DH.
ΣF⊥ = 0 → FDH = 0
Check with the method of joints
Solving all joints gives these member forces (T = tension, C = compression).
Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.
Joint G
FG and GH lie on one straight line and the joint carries no load. Balancing forces across that line leaves only CG.
ΣF⊥ = 0 → FCG = 0
Check with the method of joints
Solving all joints gives these member forces (T = tension, C = compression).
Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.
Whole frame: moments about A
By = 12·0.9/2.4 = 4.5 kN
Leg BC: moments about C
4.5·1.2 = T·1.4
T = 3.857 kN
Answer
T = 3.857 kN
8.Frames & machines
Answer: C = 1.152 kN
Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.
Support reaction at B
By = 4·1/4 = 1 kN
Tie force
T = 1·2/3.5 = 0.5714 kN
Pin force on BC
Cx = 0.5714 kN, Cy = −1 kN
C = √(0.5714² + 1²) = 1.152 kN
Answer
C = 1.152 kN
9.Shear force & bending moment
Answer: D (x = 3 m)
Largest bending moment: M changes slope wherever the shear force changes, so its peaks sit where the shear force crosses zero: under a point load, inside a distributed load, or over a support of an overhang. At a fixed support of a cantilever the moment is largest at the wall. Compare the size of M at those places, sagging or hogging.
Support reactions
Take moments about one support, then use the vertical force balance.
R1 = 29.17 kN, R2 = 25.83 kN
Bending moment at every mark
Sum the moments of all forces on one side of the cut. Sagging is positive, hogging negative.
MA = 0, MB = 27.17, MC = 50.33, MD = 69.5 kN·m, ME = 49.67, MF = 25.83, MG = 0
Answer
Mark D: MD = 69.5 kN·m
10.Shear force & bending moment
Answer: Mx = 31.5 kN·m
Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.
Support reactions
Equilibrium of the whole beam.
UDL resultant: W = w·ℓ = 4·5 = 20 kN, acting at x̄ = 2.5 m
ΣMA = 0: RB·5 = 20·1.5 + 4·5·2.5
RB = 80/5 = 16 kN
ΣFy = 0: RA = 40 − 16 = 24 kN
Cut at x = 1.5 m and keep the left part
Only forces left of the cut appear. A UDL portion acts as one force at the middle of that portion.
M = RA·x − (each load left of the cut × its distance to the cut)
Mx = 24·1.5 − 4·1.5·0.75 = 31.5 kN·m
Answer
Mx = 31.5 kN·m
11.Centroid & second moment of area
Answer: Ix = 225.4 × 10⁶ mm⁴
Sections with holes: treat a hole as a negative area. The centroid is ȳ = (A₁y₁ − A₂y₂)/(A₁ − A₂), with A₁, y₁ for the full plate and A₂, y₂ for the hole. For the second moment of area about the centroidal axis, use the parallel-axis theorem for each part and subtract the hole: I = (Ic1 + A₁d₁²) − (Ic2 + A₂d₂²), where d is the distance from each part's own centroid to the axis through ȳ. A rectangle has Ic = bh³/12 and a circle Ic = πd⁴/64.
Centroid
ȳ = (48000·120 − 1963·72)/(48000 − 1963) = 122 mm
Full plate about ȳ
200·240³/12 + 48000·−2.047² = 230.6 × 10⁶ mm⁴
Hole about ȳ
π·50⁴/64 + 1963·−50.05² = 5.225 × 10⁶ mm⁴
Subtract
Ix = 225.4 × 10⁶ mm⁴
Answer
Ix = 225.4 × 10⁶ mm⁴
12.Centroid & second moment of area
Answer: σbottom = 72.01 MPa
Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.
Split into two rectangles
Measure every y from the bottom edge.
flange: Af = 180·30 = 5400 mm², yf = 100 + 30/2 = 115 mm