Statics: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Vectors: dot & cross product

Magnitude
|a| = √(ax² + ay² + az²)
Unit vector
û = a/|a|
Components from an angle
Fx = F·cos θ, Fy = F·sin θ
Dot product
a·b = axbx + ayby + azbz = |a||b|cos θ
Scalar projection of a onto b
a·b/|b|
Work
W = F·d
Cross product
a × b = (aybz − azby, azbx − axbz, axby − aybx)
Areas
parallelogram |a × b|, triangle ½|a × b|
Moment about O
MO = r × F, r = A − O
Volume of a parallelepiped
V = |a·(b × c)|

Method

  1. Write every vector in components; for a force given by a magnitude and an angle, use F·cos θ and F·sin θ.
  2. For lengths and directions use the magnitude √(x² + y² + z²) and the unit vector a/|a|.
  3. Use the dot product for angles, projections, perpendicularity and work: a·b = |a||b|cos θ.
  4. Use the cross product for perpendicular vectors, areas and moments: write the three components carefully, keeping the order a × b.

Beam support reactions

Equilibrium
ΣFx = 0, ΣFy = 0, ΣM = 0
Uniform load
resultant w·L at the middle of the load
Moment
M = F·d

Method

  1. Draw a free-body diagram and replace each support by its reactions.
  2. Replace every distributed load by a single force at its centroid.
  3. Take moments about one support to find the reaction at the other.
  4. Use ΣFy = 0 to find the remaining reaction, and check with a second moment equation.

Truss: method of joints

Method of joints
ΣFx = 0, ΣFy = 0 at each joint
Method of sections
ΣM = 0 about a cut point
Member force
positive = tension, negative = compression

Method

  1. Find the support reactions for the whole truss.
  2. Method of joints: start at a joint with at most two unknown member forces and use ΣFx = 0 and ΣFy = 0.
  3. Method of sections: cut through the member you need and take moments about a point where the other unknown members meet.
  4. Assume tension; a negative answer means compression.

Frames & machines

Equilibrium of each member
ΣFx = 0, ΣFy = 0, ΣM = 0
Two-force member
force along the line through its two pins
Pin force
equal and opposite on the two members it joins
Magnitude of a pin force
F = √(Fx² + Fy²)
Lever, pliers, bell crank
Fin·a = Fout·b
Toggle
Flink = F/(2 sin θ), Q = F/(2 tan θ)
Uniform load
resultant w·L at the middle of the load

Method

  1. Draw the whole structure and find the support reactions if there are no more than three unknowns.
  2. Spot the two-force members: loaded only at two pins, their force acts along the line between the pins.
  3. Take the frame apart and draw every member on its own, with equal and opposite pin forces where members meet.
  4. For each member, take moments about a pin with unknown forces, then use ΣFx = 0 and ΣFy = 0; combine components into a magnitude at the end.

Shear force & bending moment

Shear and moment
V = ΣF on one side, M = ΣF·d on one side
Bending stress
σ = M·y/I
Rectangle
I = bh³/12
Section modulus
W = I/ymax
Simply supported, uniform load
Mmax = wL²/8

Method

  1. Find the support reactions from equilibrium of the whole beam.
  2. Cut the beam at the section you need and keep one side.
  3. Shear force: sum of the vertical forces on that side. Bending moment: sum of their moments about the cut.
  4. For the maximum moment, find where the shear force is zero.

Centroid & second moment of area

Centroid
ȳ = ΣAiyi/ΣAi
Rectangle
I = bh³/12
Parallel-axis theorem
I = Ic + A·d²
Composite section
I = Σ(Ic,i + Aidi²)

2Practice problems

1.Vectors: dot & cross productMedium
xyzab

Find the dot product a·b of a = (6, −2, 6) and b = (−3, 2, 1).

a = (6, −2, 6)b = (−3, 2, 1)
a·b =
2.Vectors: dot & cross productHard
xyzab

The unit vector n̂ is perpendicular to both a = (0, −5, −1) and b = (−5, 2, −4) and has a positive z-component. Find its y-component n̂y.

a = (0, −5, −1)b = (−5, 2, −4)n̂z > 0
n̂y =
3.Beam support reactionsMedium
P = 25 kNM = 50 kN·mABRB​ = ?3.5 m1 m0.5 m

The simply supported beam has a pin at A and a roller at B. It carries a point load P at 3.5 m from A and a counter-clockwise couple M at 4.5 m from A. Find the vertical reaction RB, taking upward as positive.

L = 5 mP = 25 kN at 3.5 mM = 50 kN·m (counter-clockwise) at 4.5 m
RB = kN
4.Beam support reactionsHard
P = 70 kNQ = 20 kNADCMA​ = ?1 m4 m4 m1 m

A compound beam is fixed to the wall at A, has an internal hinge at C (5 m from A) and rests on a roller at D (10 m from A). It carries a point load P at 9 m from A and a point load Q at 1 m from A. Find the magnitude of the reaction moment MA at the wall.

AC = 5 mAD = 10 mP = 70 kN at 9 mQ = 20 kN at 1 m
MA = kN·m
5.Truss: method of jointsMedium
ABCDEFGH40 kN20 kN40 kN40 kN35 kN4 × 4 m3 m

Exactly one member of this truss carries no force under these loads. Which is the zero-force member? Click it in the diagram.

B: 40 kN ↓C: 20 kN ↓D: 40 kN ↓F: 40 kN ↓H: 35 kN ↓
  1. 1member AB
  2. 2member BC
  3. 3member CD
  4. 4member DE
  5. 5member FG
  6. 6member GH
  7. 7member AF
  8. 8member HE
  9. 9member BF
  10. 10member CG
  11. 11member DH
  12. 12member FC
  13. 13member HC
6.Truss: method of jointsHard
ABBCACACB25 kN30 kN6 m1 m3 m

Use the method of joints to find the force FAB in member AB. Give tension as positive and compression as negative.

span = 6 mheight = 3 mB is 1 m from Avertical load = 25 kNhorizontal load = 30 kN →
FAB = kN
7.Frames & machinesMedium
10 kN6 m2.5 m0.9 mABCK

The frame shown has pins at A, B and C; A and C are fixed to the ground 6 m apart, and B is 2.5 m above the ground and 0.9 m to the right of A. A vertical load of 10 kN acts on member AB at K, 0.45 m (horizontally) from A. Find the force FBC in member BC.

P = 10 kNL = 6 mH = 2.5 mhorizontal distance A to B = 0.9 mhorizontal distance A to K = 0.45 m
FBC = kN
8.Frames & machinesHard
10 kN2 kN6 m2 m2.7 mABCK

The frame shown has pins at A, B and C; A and C are fixed to the ground 6 m apart, and B is 2 m high and 2.7 m to the right of A. Member AB carries a vertical load of 10 kN at K, 1.08 m (horizontally) from A, and a horizontal load of 2 kN to the right acts at B on member AB. Find the size of the horizontal reaction Ax at A.

P = 10 kNQ = 2 kNL = 6 mH = 2 mhorizontal distance A to B = 2.7 mhorizontal distance A to K = 1.08 m
Ax = kN
9.Shear force & bending momentMedium
8 kN/m35 kNABCDEFG1 m1 m1 m1 m1 m1 m

The marks A to G split the beam into six equal parts. At which mark is the bending moment largest in size, sagging or hogging? Click it in the diagram.

35 kN @ 3 m8 kN/m, 1–5 m
  1. 1A (x = 0 m)
  2. 2B (x = 1 m)
  3. 3C (x = 2 m)
  4. 4D (x = 3 m)
  5. 5E (x = 4 m)
  6. 6F (x = 5 m)
  7. 7G (x = 6 m)
10.Shear force & bending momentHard
8 kN/m40 kN35 kN50 kNABCDEFG2 m2 m2 m2 m2 m2 m

The marks A to G split the beam into six equal parts. At which mark is the bending moment largest in size, sagging or hogging? Click it in the diagram.

40 kN @ 0 m35 kN @ 12 m50 kN @ 6 m8 kN/m, 2–10 m
  1. 1A (x = 0 m)
  2. 2B (x = 2 m)
  3. 3C (x = 4 m)
  4. 4D (x = 6 m)
  5. 5E (x = 8 m)
  6. 6F (x = 10 m)
  7. 7G (x = 12 m)
11.Centroid & second moment of areaMedium
120 mm300 mm120 mmØ60xIx​ = ?

A 120 mm × 300 mm plate has a circular hole of diameter 60 mm on its vertical centre line, with its centre 120 mm above the bottom. Find the second moment of area Ix about the horizontal axis through the centroid.

b = 120 mmh = 300 mmd = 60 mmhole centre: y = 120 mm
Ix = × 10⁶ mm⁴
12.Centroid & second moment of areaHard
1104801412xM = 60 kN·mdimensions in mm

A symmetric I-section has flanges 110 mm wide and 14 mm thick, an overall depth of 480 mm and a web 12 mm thick. It carries a bending moment of 60 kN·m about the axis x. Find the size of the bending stress σj at the junction of the web and the top flange.

B = 110 mmH = 480 mmtf = 14 mmtw = 12 mmM = 60 kN·m
σj = MPa

3Solutions

1.Vectors: dot & cross product

Answer: a·b = −16

Dot product: a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.

Multiply matching components and add

a·b = 6·(−3) + (−2)·2 + 6·1 = (−18) + (−4) + 6 = −16

Answer

a·b = −16

Negative: the angle between the vectors is more than 90°.

2.Vectors: dot & cross product

Answer: n̂y = −0.1485

Cross product: a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.

Cross product

(a × b)x = aybz − azby = (−5)·(−4) − (−1)·2 = 22
(a × b)y = azbx − axbz = (−1)·(−5) − 0·(−4) = 5
(a × b)z = axby − aybx = 0·2 − (−5)·(−5) = −25

Normalise

The z-component of a × b is negative, so use −(a × b).

|a × b| = √(22² + 5² + (−25)²) = 33.67
n̂ = −(22, 5, −25)/33.67 = (−0.6533, −0.1485, 0.7424)
n̂y = −0.1485

Answer

n̂y = −0.1485
3.Beam support reactions

Answer: RB = 7.5 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Replace each distributed load by its resultant (its area) acting at the centroid of the load diagram, and take moments about a support to remove that support’s reaction from the equation.

Moments about A

Counter-clockwise positive.

ΣMA = 0: RB·5 − 25·3.5 + 50 = 0
RB = 37.5/5 = 7.5 kN

Vertical equilibrium

RA = 25 − 7.5 = 17.5 kN

Answer

RB = 7.5 kN

A negative reaction acts downward.

4.Beam support reactions

Answer: MA = 90 kN·m

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Replace each distributed load by its resultant (its area) acting at the centroid of the load diagram, and take moments about a support to remove that support’s reaction from the equation. An internal hinge cannot carry a bending moment, which gives one extra equation: the moment about the hinge of the forces on either side is zero.

Part CD

The hinge has no moment, so moments about C on CD alone must balance.

ΣMC = 0: RD·5 = 70·4
RD = 56 kN
VC = 70 − 56 = 14 kN

Part AC

The hinge force VC acts downward on AC (equal and opposite to its action on CD).

RA = 20 + 14 = 34 kN
MA = 20·1 + 14·5 = 90 kN·m

Answer

MA = 90 kN·m
5.Truss: method of joints

Answer: member CG

Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.

Joint G

FG and GH lie on one straight line and the joint carries no load. Balancing forces across that line leaves only CG.

ΣF⊥ = 0 → FCG = 0

Check with the method of joints

Solving all joints gives these member forces (T = tension, C = compression).

AB: 118.3 kN (T), BC: 118.3 kN (T), CD: 115 kN (T), DE: 115 kN (T), FG: 130 kN (C), GH: 130 kN (C), AF: 147.9 kN (C), HE: 143.7 kN (C), BF: 40 kN (T), CG: 0, DH: 40 kN (T), FC: 14.58 kN (T), HC: 18.75 kN (T)

Answer

Zero-force member: CG
6.Truss: method of joints

Answer: FAB = −6.149 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB25 kN30 kNAy​Cy​Ax​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·6 = 25·1 + 30·3 → Cy = 19.17 kN
ΣFy = 0: Ay = 25 − 19.17 = 5.833 kN
ΣFx = 0: Ax = −30 kN

Joint A

Assume every member is in tension (pulling away from the joint). Only AB has a vertical component at A.

sin α = 3/3.162 = 0.9487
ΣFy = 0: Ay + FAB·sin α = 0
FAB = −5.833/0.9487 = −6.149 kN

Answer

FAB = −6.149 kN (compression)
7.Frames & machines

Answer: FBC = 1.704 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Two-force member BC

BC = √(5.1² + 2.5²) = 5.68 m

Whole frame: moments about A

The ground pushes on BC at C along CB; its horizontal component passes through A, only the vertical one has a moment.

FBC·(2.5/5.68)·6 = 10·0.45
FBC = 1.704 kN (compression)

Answer

FBC = 1.704 kN
8.Frames & machines

Answer: Ax = 2.07 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Direction of BC

BC = 3.859 m, cos = 0.8552, sin = 0.5183

Whole frame: moments about A

FBC·0.5183·6 = 10·1.08 + 2·2
FBC = 4.759 kN

Horizontal balance

Ax + 2 − 4.759·0.8552 = 0
Ax = 2.07 kN → |Ax| = 2.07 kN

Answer

Ax = 2.07 kN

Ax points to the right.

9.Shear force & bending moment

Answer: D (x = 3 m)

Largest bending moment: M changes slope wherever the shear force changes, so its peaks sit where the shear force crosses zero: under a point load, inside a distributed load, or over a support of an overhang. At a fixed support of a cantilever the moment is largest at the wall. Compare the size of M at those places, sagging or hogging.

Support reactions

Take moments about one support, then use the vertical force balance.

R1 = 33.5 kN, R2 = 33.5 kN

Bending moment at every mark

Sum the moments of all forces on one side of the cut. Sagging is positive, hogging negative.

MA = 0, MB = 33.5, MC = 63, MD = 84.5 kN·m, ME = 63, MF = 33.5, MG = 0

Answer

Mark D: MD = 84.5 kN·m
10.Shear force & bending moment

Answer: D (x = 6 m)

Largest bending moment: M changes slope wherever the shear force changes, so its peaks sit where the shear force crosses zero: under a point load, inside a distributed load, or over a support of an overhang. At a fixed support of a cantilever the moment is largest at the wall. Compare the size of M at those places, sagging or hogging.

Support reactions

Take moments about one support, then use the vertical force balance.

R1 = 98.25 kN, R2 = 90.75 kN

Bending moment at every mark

Sum the moments of all forces on one side of the cut. Sagging is positive, hogging negative.

MA = 0, MB = −80, MC = 20.5, MD = 89 kN·m, ME = 25.5, MF = −70, MG = 0

Answer

Mark D: MD = 89 kN·m
11.Centroid & second moment of area

Answer: Ix = 266.6 × 10⁶ mm⁴

Sections with holes: treat a hole as a negative area. The centroid is ȳ = (A₁y₁ − A₂y₂)/(A₁ − A₂), with A₁, y₁ for the full plate and A₂, y₂ for the hole. For the second moment of area about the centroidal axis, use the parallel-axis theorem for each part and subtract the hole: I = (Ic1 + A₁d₁²) − (Ic2 + A₂d₂²), where d is the distance from each part's own centroid to the axis through ȳ. A rectangle has Ic = bh³/12 and a circle Ic = πd⁴/64.

Centroid

ȳ = (36000·150 − 2827·120)/(36000 − 2827) = 152.6 mm

Full plate about ȳ

120·300³/12 + 36000·−2.557² = 270.2 × 10⁶ mm⁴

Hole about ȳ

π·60⁴/64 + 2827·−32.56² = 3.633 × 10⁶ mm⁴

Subtract

Ix = 266.6 × 10⁶ mm⁴

Answer

Ix = 266.6 × 10⁶ mm⁴
12.Centroid & second moment of area

Answer: σj = 52.23 MPa

Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.

Outer rectangle minus the two side cut-outs

Both cut-outs together are (B − tw) wide and hw = H − 2tf high, and share the axis x.

hw = 480 − 2·14 = 452 mm
Ix = (B·H³ − (B − tw)·hw³)/12 = (110·480³ − 98·452³)/12
Ix = 2.596 × 10⁸ mm⁴

Bending stress

y = 240 − 14 = 226 mm
σ = M·y/I = 6 × 10⁷·226/2.596 × 10⁸ = 52.23 MPa

Answer

σj = 52.23 MPa

ExamProblems · examproblems.com/courses/statics