Statics: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Vectors: dot & cross product

Magnitude
|a| = √(ax² + ay² + az²)
Unit vector
û = a/|a|
Components from an angle
Fx = F·cos θ, Fy = F·sin θ
Dot product
a·b = axbx + ayby + azbz = |a||b|cos θ
Scalar projection of a onto b
a·b/|b|
Work
W = F·d
Cross product
a × b = (aybz − azby, azbx − axbz, axby − aybx)
Areas
parallelogram |a × b|, triangle ½|a × b|
Moment about O
MO = r × F, r = A − O
Volume of a parallelepiped
V = |a·(b × c)|

Method

  1. Write every vector in components; for a force given by a magnitude and an angle, use F·cos θ and F·sin θ.
  2. For lengths and directions use the magnitude √(x² + y² + z²) and the unit vector a/|a|.
  3. Use the dot product for angles, projections, perpendicularity and work: a·b = |a||b|cos θ.
  4. Use the cross product for perpendicular vectors, areas and moments: write the three components carefully, keeping the order a × b.

Beam support reactions

Equilibrium
ΣFx = 0, ΣFy = 0, ΣM = 0
Uniform load
resultant w·L at the middle of the load
Moment
M = F·d

Method

  1. Draw a free-body diagram and replace each support by its reactions.
  2. Replace every distributed load by a single force at its centroid.
  3. Take moments about one support to find the reaction at the other.
  4. Use ΣFy = 0 to find the remaining reaction, and check with a second moment equation.

Truss: method of joints

Method of joints
ΣFx = 0, ΣFy = 0 at each joint
Method of sections
ΣM = 0 about a cut point
Member force
positive = tension, negative = compression

Method

  1. Find the support reactions for the whole truss.
  2. Method of joints: start at a joint with at most two unknown member forces and use ΣFx = 0 and ΣFy = 0.
  3. Method of sections: cut through the member you need and take moments about a point where the other unknown members meet.
  4. Assume tension; a negative answer means compression.

Frames & machines

Equilibrium of each member
ΣFx = 0, ΣFy = 0, ΣM = 0
Two-force member
force along the line through its two pins
Pin force
equal and opposite on the two members it joins
Magnitude of a pin force
F = √(Fx² + Fy²)
Lever, pliers, bell crank
Fin·a = Fout·b
Toggle
Flink = F/(2 sin θ), Q = F/(2 tan θ)
Uniform load
resultant w·L at the middle of the load

Method

  1. Draw the whole structure and find the support reactions if there are no more than three unknowns.
  2. Spot the two-force members: loaded only at two pins, their force acts along the line between the pins.
  3. Take the frame apart and draw every member on its own, with equal and opposite pin forces where members meet.
  4. For each member, take moments about a pin with unknown forces, then use ΣFx = 0 and ΣFy = 0; combine components into a magnitude at the end.

Shear force & bending moment

Shear and moment
V = ΣF on one side, M = ΣF·d on one side
Bending stress
σ = M·y/I
Rectangle
I = bh³/12
Section modulus
W = I/ymax
Simply supported, uniform load
Mmax = wL²/8

Method

  1. Find the support reactions from equilibrium of the whole beam.
  2. Cut the beam at the section you need and keep one side.
  3. Shear force: sum of the vertical forces on that side. Bending moment: sum of their moments about the cut.
  4. For the maximum moment, find where the shear force is zero.

Centroid & second moment of area

Centroid
ȳ = ΣAiyi/ΣAi
Rectangle
I = bh³/12
Parallel-axis theorem
I = Ic + A·d²
Composite section
I = Σ(Ic,i + Aidi²)

2Practice problems

1.Vectors: dot & cross productMedium
xyzab

Find the angle θ between the vectors a = (2, 6, 1) and b = (4, 4, −6), in degrees.

a = (2, 6, 1)b = (4, 4, −6)
θ = °
2.Vectors: dot & cross productHard
xyzrFOA

A force F = (30, 50, −10) N acts at point A(−3, 4, −3). Coordinates are in metres. Find the z-component Mz of the moment of the force about point O(2, −2, 0).

F = (30, 50, −10) NA(−3, 4, −3) mO(2, −2, 0) m
Mz = N·m
3.Beam support reactionsMedium
P1​ = 55 kNP2​ = 10 kNABCRB​ = ?3 m3 m2 m

The beam has a pin at A and a roller at B, 6 m from A, and overhangs B to the free end C. Find the vertical reaction RB, taking upward as positive.

AB = 6 mAC = 8 mP1 = 55 kN at 3 mP2 = 10 kN at 8 m
RB = kN
4.Beam support reactionsHard
w = 5 kN/mP = 30 kNABCRB​ = ?0.5 m2 m1.5 m

The beam has a pin at A and a roller at B, 2.5 m from A, and overhangs B to the free end C. It carries a point load P at 0.5 m from A and a uniformly distributed load w from 2.5 m to the free end at 4 m. Find the vertical reaction RB, taking upward as positive.

AB = 2.5 mAC = 4 mP = 30 kN at 0.5 mw = 5 kN/m from 2.5 to 4 m
RB = kN
5.Truss: method of jointsMedium
ABBCACACB40 kN6 m1 m4 m

Use the method of joints to find the force FBC in member BC. Give tension as positive and compression as negative.

span = 6 mheight = 4 mB is 1 m from Avertical load = 40 kN
FBC = kN
6.Truss: method of jointsHard
ABBCACACB20 kN25 kN5 m4 m3 m

Use the method of joints to find the force FAC in member AC. Give tension as positive and compression as negative.

span = 5 mheight = 3 mB is 4 m from Avertical load = 20 kNhorizontal load = 25 kN ←
FAC = kN
7.Frames & machinesMedium
8 kN4 m2.5 m2.4 mABCK

The frame shown has pins at A, B and C; A and C are fixed to the ground 4 m apart, and B is 2.5 m above the ground and 2.4 m to the right of A. A vertical load of 8 kN acts on member AB at K, 1.44 m (horizontally) from A. Find the force FBC in member BC.

P = 8 kNL = 4 mH = 2.5 mhorizontal distance A to B = 2.4 mhorizontal distance A to K = 1.44 m
FBC = kN
8.Frames & machinesHard
10 kN2 m1 m2 m0.6 mABCDEK

The A-frame shown stands on a pin at A and a roller at B, 2 m apart, with its apex pin C 3 m high and the horizontal tie DE 1 m above the ground. A vertical load of 10 kN acts on leg AC at K, 0.6 m (horizontally) from A. Find the magnitude of the force C that the pin C exerts on leg BC.

P = 10 kNAB = 2 mheight of C = 3 mheight of DE = 1 mhorizontal distance A to K = 0.6 m
C = kN
9.Shear force & bending momentMedium
5 kN/m25 kNABCDEFG1 m1 m1 m1 m1 m1 m

The marks A to G split the beam into six equal parts. At which mark is the bending moment largest in size, sagging or hogging? Click it in the diagram.

25 kN @ 3 m5 kN/m, 2–6 m
  1. 1A (x = 0 m)
  2. 2B (x = 1 m)
  3. 3C (x = 2 m)
  4. 4D (x = 3 m)
  5. 5E (x = 4 m)
  6. 6F (x = 5 m)
  7. 7G (x = 6 m)
10.Shear force & bending momentHard
4 kN/m40 kN30 kNABCDEFG2 m2 m2 m2 m2 m2 m

The marks A to G split the beam into six equal parts. At which mark is the bending moment largest in size, sagging or hogging? Click it in the diagram.

40 kN @ 0 m30 kN @ 12 m4 kN/m, 2–8 m
  1. 1A (x = 0 m)
  2. 2B (x = 2 m)
  3. 3C (x = 4 m)
  4. 4D (x = 6 m)
  5. 5E (x = 8 m)
  6. 6F (x = 10 m)
  7. 7G (x = 12 m)
11.Centroid & second moment of areaMedium
2203026012xdimensions in mm

Find the second moment of area Ix of the T-section about the horizontal axis x through its centroid.

bf = 220 mmtf = 30 mmtw = 12 mmhw = 260 mm
Ix = × 10⁶ mm⁴
12.Centroid & second moment of areaHard
200 mm150 mm60 mm80 × 50xIx​ = ?

A 200 mm × 150 mm plate has a rectangular cut-out 80 mm wide and 50 mm high, centred on the vertical centre line with its centre 60 mm above the bottom. Find the second moment of area Ix about the horizontal axis through the centroid.

b = 200 mmh = 150 mmcut-out: 80 × 50 mmhole centre: y = 60 mm
Ix = × 10⁶ mm⁴

3Solutions

1.Vectors: dot & cross product

Answer: θ = 60.5 °

Dot product: a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.

Dot product

a·b = 2·4 + 6·4 + 1·(−6) = 26

Magnitudes

|a| = √(2² + 6² + 1²) = 6.403
|b| = √(4² + 4² + (−6)²) = 8.246

Angle

cos θ = 26/(6.403·8.246) = 0.4924
θ = arccos(0.4924) = 60.5°

Answer

θ = 60.5°
2.Vectors: dot & cross product

Answer: Mz = −430 N·m

Cross product: a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.

Position vector from O to A

r = A − O = (−3, 4, −3) − (2, −2, 0) = (−5, 6, −3) m

Moment M = r × F

(r × F)x = ryFz − rzFy = 6·(−10) − (−3)·50 = 90 N·m
(r × F)y = rzFx − rxFz = (−3)·30 − (−5)·(−10) = −140 N·m
(r × F)z = rxFy − ryFx = (−5)·50 − 6·30 = −430 N·m

Requested component

Mz = −430 N·m

Answer

Mz = −430 N·m
3.Beam support reactions

Answer: RB = 40.83 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Replace each distributed load by its resultant (its area) acting at the centroid of the load diagram, and take moments about a support to remove that support’s reaction from the equation.

Moments about A

Counter-clockwise positive.

ΣMA = 0: RB·6 = 55·3 + 10·8
RB = 245/6 = 40.83 kN

Vertical equilibrium

RA = 55 + 10 − 40.83 = 24.17 kN

Answer

RB = 40.83 kN
4.Beam support reactions

Answer: RB = 15.75 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Replace each distributed load by its resultant (its area) acting at the centroid of the load diagram, and take moments about a support to remove that support’s reaction from the equation.

Resultant of the distributed load

W = 5·1.5 = 7.5 kN, x̄ = (2.5 + 4)/2 = 3.25 m

Equilibrium

Moments about A, counter-clockwise positive. Then vertical force balance.

ΣMA = 0: RB·2.5 = 30·0.5 + 7.5·3.25
RB = 39.38/2.5 = 15.75 kN
RA = 37.5 − 15.75 = 21.75 kN

Answer

RB = 15.75 kN
5.Truss: method of joints

Answer: FBC = −10.67 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB40 kNAy​Cy​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·6 = 40·1 → Cy = 6.667 kN
ΣFy = 0: Ay = 40 − 6.667 = 33.33 kN

Joint C

The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.

sin γ = 4/6.403 = 0.6247, cos γ = 5/6.403 = 0.7809
ΣFy = 0: Cy + FBC·sin γ = 0 → FBC = −6.667/0.6247 = −10.67 kN

Answer

FBC = −10.67 kN (compression)
6.Truss: method of joints

Answer: FAC = 0.3333 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB20 kN25 kNAy​Cy​Ax​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·5 = 20·4 − 25·3 → Cy = 1 kN
ΣFy = 0: Ay = 20 − 1 = 19 kN
ΣFx = 0: Ax = 25 kN

Joint C

The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.

sin γ = 3/3.162 = 0.9487, cos γ = 1/3.162 = 0.3162
ΣFy = 0: Cy + FBC·sin γ = 0 → FBC = −1/0.9487 = −1.054 kN
ΣFx = 0: −FAC − FBC·cos γ = 0 → FAC = −(−1.054)·0.3162 = 0.3333 kN

Answer

FAC = 0.3333 kN (tension)
7.Frames & machines

Answer: FBC = 3.419 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Two-force member BC

BC = √(1.6² + 2.5²) = 2.968 m

Whole frame: moments about A

The ground pushes on BC at C along CB; its horizontal component passes through A, only the vertical one has a moment.

FBC·(2.5/2.968)·4 = 8·1.44
FBC = 3.419 kN (compression)

Answer

FBC = 3.419 kN
8.Frames & machines

Answer: C = 3.354 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Support reaction at B

By = 10·0.6/2 = 3 kN

Tie force

T = 3·1/2 = 1.5 kN

Pin force on BC

Cx = 1.5 kN, Cy = −3 kN
C = √(1.5² + 3²) = 3.354 kN

Answer

C = 3.354 kN
9.Shear force & bending moment

Answer: D (x = 3 m)

Largest bending moment: M changes slope wherever the shear force changes, so its peaks sit where the shear force crosses zero: under a point load, inside a distributed load, or over a support of an overhang. At a fixed support of a cantilever the moment is largest at the wall. Compare the size of M at those places, sagging or hogging.

Support reactions

Take moments about one support, then use the vertical force balance.

R1 = 19.17 kN, R2 = 25.83 kN

Bending moment at every mark

Sum the moments of all forces on one side of the cut. Sagging is positive, hogging negative.

MA = 0, MB = 19.17, MC = 38.33, MD = 55 kN·m, ME = 41.67, MF = 23.33, MG = 0

Answer

Mark D: MD = 55 kN·m
10.Shear force & bending moment

Answer: E (x = 8 m)

Largest bending moment: M changes slope wherever the shear force changes, so its peaks sit where the shear force crosses zero: under a point load, inside a distributed load, or over a support of an overhang. At a fixed support of a cantilever the moment is largest at the wall. Compare the size of M at those places, sagging or hogging.

Support reactions

Take moments about one support, then use the vertical force balance.

R1 = 45.33 kN, R2 = 48.67 kN

Bending moment at every mark

Sum the moments of all forces on one side of the cut. Sagging is positive, hogging negative.

MA = 0, MB = −80, MC = −77.33, MD = −90.67, ME = −120 kN·m, MF = −60, MG = 0

Answer

Mark E: ME = −120 kN·m
11.Centroid & second moment of area

Answer: Ix = 62.61 × 10⁶ mm⁴

Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.

Split into two rectangles

Measure every y from the bottom edge.

flange: Af = 220·30 = 6600 mm², yf = 260 + 30/2 = 275 mm
web: Aw = 12·260 = 3120 mm², yw = 260/2 = 130 mm

Centroid

ȳ = (Afyf + Awyw)/(Af + Aw) = (6600·275 + 3120·130)/9720 = 228.5 mm

Parallel-axis theorem

flange: 220·30³/12 + 6600·(275 − 228.5)² = 1.479 × 10⁷ mm⁴
web: 12·260³/12 + 3120·(130 − 228.5)² = 4.782 × 10⁷ mm⁴
Ix = 1.479 × 10⁷ + 4.782 × 10⁷ = 6.261 × 10⁷ mm⁴ = 62.61 × 10⁶ mm⁴

Answer

Ix = 62.61 × 10⁶ mm⁴
12.Centroid & second moment of area

Answer: Ix = 54.38 × 10⁶ mm⁴

Sections with holes: treat a hole as a negative area. The centroid is ȳ = (A₁y₁ − A₂y₂)/(A₁ − A₂), with A₁, y₁ for the full plate and A₂, y₂ for the hole. For the second moment of area about the centroidal axis, use the parallel-axis theorem for each part and subtract the hole: I = (Ic1 + A₁d₁²) − (Ic2 + A₂d₂²), where d is the distance from each part's own centroid to the axis through ȳ. A rectangle has Ic = bh³/12 and a circle Ic = πd⁴/64.

Centroid

ȳ = (30000·75 − 4000·60)/(30000 − 4000) = 77.31 mm

Full plate about ȳ

200·150³/12 + 30000·−2.308² = 56.41 × 10⁶ mm⁴

Hole about ȳ

80·50³/12 + 4000·−17.31² = 2.032 × 10⁶ mm⁴

Subtract

Ix = 54.38 × 10⁶ mm⁴

Answer

Ix = 54.38 × 10⁶ mm⁴

ExamProblems · examproblems.com/courses/statics