Statics: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Vectors: dot & cross product

Magnitude
|a| = √(ax² + ay² + az²)
Unit vector
û = a/|a|
Components from an angle
Fx = F·cos θ, Fy = F·sin θ
Dot product
a·b = axbx + ayby + azbz = |a||b|cos θ
Scalar projection of a onto b
a·b/|b|
Work
W = F·d
Cross product
a × b = (aybz − azby, azbx − axbz, axby − aybx)
Areas
parallelogram |a × b|, triangle ½|a × b|
Moment about O
MO = r × F, r = A − O
Volume of a parallelepiped
V = |a·(b × c)|

Method

  1. Write every vector in components; for a force given by a magnitude and an angle, use F·cos θ and F·sin θ.
  2. For lengths and directions use the magnitude √(x² + y² + z²) and the unit vector a/|a|.
  3. Use the dot product for angles, projections, perpendicularity and work: a·b = |a||b|cos θ.
  4. Use the cross product for perpendicular vectors, areas and moments: write the three components carefully, keeping the order a × b.

Beam support reactions

Equilibrium
ΣFx = 0, ΣFy = 0, ΣM = 0
Uniform load
resultant w·L at the middle of the load
Moment
M = F·d

Method

  1. Draw a free-body diagram and replace each support by its reactions.
  2. Replace every distributed load by a single force at its centroid.
  3. Take moments about one support to find the reaction at the other.
  4. Use ΣFy = 0 to find the remaining reaction, and check with a second moment equation.

Truss: method of joints

Method of joints
ΣFx = 0, ΣFy = 0 at each joint
Method of sections
ΣM = 0 about a cut point
Member force
positive = tension, negative = compression

Method

  1. Find the support reactions for the whole truss.
  2. Method of joints: start at a joint with at most two unknown member forces and use ΣFx = 0 and ΣFy = 0.
  3. Method of sections: cut through the member you need and take moments about a point where the other unknown members meet.
  4. Assume tension; a negative answer means compression.

Frames & machines

Equilibrium of each member
ΣFx = 0, ΣFy = 0, ΣM = 0
Two-force member
force along the line through its two pins
Pin force
equal and opposite on the two members it joins
Magnitude of a pin force
F = √(Fx² + Fy²)
Lever, pliers, bell crank
Fin·a = Fout·b
Toggle
Flink = F/(2 sin θ), Q = F/(2 tan θ)
Uniform load
resultant w·L at the middle of the load

Method

  1. Draw the whole structure and find the support reactions if there are no more than three unknowns.
  2. Spot the two-force members: loaded only at two pins, their force acts along the line between the pins.
  3. Take the frame apart and draw every member on its own, with equal and opposite pin forces where members meet.
  4. For each member, take moments about a pin with unknown forces, then use ΣFx = 0 and ΣFy = 0; combine components into a magnitude at the end.

Shear force & bending moment

Shear and moment
V = ΣF on one side, M = ΣF·d on one side
Bending stress
σ = M·y/I
Rectangle
I = bh³/12
Section modulus
W = I/ymax
Simply supported, uniform load
Mmax = wL²/8

Method

  1. Find the support reactions from equilibrium of the whole beam.
  2. Cut the beam at the section you need and keep one side.
  3. Shear force: sum of the vertical forces on that side. Bending moment: sum of their moments about the cut.
  4. For the maximum moment, find where the shear force is zero.

Centroid & second moment of area

Centroid
ȳ = ΣAiyi/ΣAi
Rectangle
I = bh³/12
Parallel-axis theorem
I = Ic + A·d²
Composite section
I = Σ(Ic,i + Aidi²)

2Practice problems

1.Vectors: dot & cross productMedium
xyzab

Find the angle θ between the vectors a = (6, −4, −4) and b = (0, 1, −6), in degrees.

a = (6, −4, −4)b = (0, 1, −6)
θ = °
2.Vectors: dot & cross productHard
xyzabc

Find the volume V of the parallelepiped whose edges from one corner are a = (−3, 0, −1), b = (−3, 1, −1) and c = (−5, 2, 0).

a = (−3, 0, −1)b = (−3, 1, −1)c = (−5, 2, 0)
V =
3.Beam support reactionsMedium
P1​ = 45 kNP2​ = 10 kNABCRA​ = ?0.5 m2.5 m2 m

The beam has a pin at A and a roller at B, 3 m from A, and overhangs B to the free end C. Find the vertical reaction RA, taking upward as positive.

AB = 3 mAC = 5 mP1 = 45 kN at 0.5 mP2 = 10 kN at 5 m
RA = kN
4.Beam support reactionsHard
w = 10 kN/mP = 30 kNABRA​ = ?RB​1 m1 m2 m2 m

The simply supported beam has a pin at A and a roller at B. Find the vertical support reaction RA.

L = 6 mP = 30 kN at 4 mw = 10 kN/m from 1 to 2 m
RA = kN
5.Truss: method of jointsMedium
ABBCACACB40 kN5 m3 m3 m

Use the method of joints to find the force FBC in member BC. Give tension as positive and compression as negative.

span = 5 mheight = 3 mB is 3 m from Avertical load = 40 kN
FBC = kN
6.Truss: method of jointsHard
ABBCACACB25 kN5 kN6 m2 m3 m

Use the method of joints to find the force FAC in member AC. Give tension as positive and compression as negative.

span = 6 mheight = 3 mB is 2 m from Avertical load = 25 kNhorizontal load = 5 kN →
FAC = kN
7.Frames & machinesMedium
4 kN4.8 m1.2 m2.4 mABCDE

The A-frame shown stands on a pin at A and a roller at B, 4.8 m apart. The legs meet at the pin C, 3.6 m high, and the horizontal tie DE is 1.2 m above the ground. A load of 4 kN acts at C. Find the magnitude of the force C that the pin C exerts on leg BC.

P = 4 kNAB = 4.8 mheight of C = 3.6 mheight of DE = 1.2 m
C = kN
8.Frames & machinesHard
w = 1 kN/m4 kN1.5 m1 m1.2 mABCD

The beam AB of the wall bracket shown is pinned at A and propped by the strut CD (C is 1.2 m below A). The beam carries a uniform load of 1 kN/m over its full length and a point load of 4 kN at its free end B. Find the force FCD in the strut.

w = 1 kN/mP = 4 kNAD = 1.5 mAB = 2.5 mAC = 1.2 m
FCD = kN
9.Shear force & bending momentMedium
P1​ = 40 kNP2​ = 45 kNABC1 m3 m1 m

The beam rests on a pin at A and a roller at B and overhangs B by 1 m to the free end C. It carries a point load P1 between the supports and a point load P2 at C. Find the shear force Vx just to the left of support B. Use sagging moments positive and upward shear on the left face positive.

L = 5 mP1 = 40 kN at 1 mP2 = 45 kN at 5 msupports at x = 0 and x = 4 m
Vx = kN
10.Shear force & bending momentHard
w = 24 kN/mAB6 m2 m

The simply supported beam carries a uniformly distributed load over part of its span. Find the maximum bending moment Mmax in the beam.

L = 8 mw = 24 kN/m from 0 to 6 m
Mmax = kN·m
11.Centroid & second moment of areaMedium
xD = 90d = 74dimensions in mm

A circular tube has outside diameter D = 90 mm and inside diameter d = 74 mm. Find its radius of gyration r about the horizontal centroidal axis.

D = 90 mmd = 74 mm
r = mm
12.Centroid & second moment of areaHard
210400188xM = 60 kN·mdimensions in mm

A symmetric I-section has flanges 210 mm wide and 18 mm thick, an overall depth of 400 mm and a web 8 mm thick. It carries a bending moment of 60 kN·m about the axis x. Find the size of the maximum bending stress σmax in the section.

B = 210 mmH = 400 mmtf = 18 mmtw = 8 mmM = 60 kN·m
σmax = MPa

3Solutions

1.Vectors: dot & cross product

Answer: θ = 66.5 °

Dot product: a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.

Dot product

a·b = 6·0 + (−4)·1 + (−4)·(−6) = 20

Magnitudes

|a| = √(6² + (−4)² + (−4)²) = 8.246
|b| = √(0² + 1² + (−6)²) = 6.083

Angle

cos θ = 20/(8.246·6.083) = 0.3987
θ = arccos(0.3987) = 66.5°

Answer

θ = 66.5°
2.Vectors: dot & cross product

Answer: V = 5

Cross product: a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.

Cross product b × c

(b × c)x = bycz − bzcy = 1·0 − (−1)·2 = 2
(b × c)y = bzcx − bxcz = (−1)·(−5) − (−3)·0 = 5
(b × c)z = bxcy − bycx = (−3)·2 − 1·(−5) = −1

Dot product with a

a·(b × c) = (−3)·2 + 0·5 + (−1)·(−1) = −5
V = |−5| = 5

Answer

V = 5
3.Beam support reactions

Answer: RA = 30.83 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Replace each distributed load by its resultant (its area) acting at the centroid of the load diagram, and take moments about a support to remove that support’s reaction from the equation.

Moments about A

Counter-clockwise positive.

ΣMA = 0: RB·3 = 45·0.5 + 10·5
RB = 72.5/3 = 24.17 kN

Vertical equilibrium

RA = 45 + 10 − 24.17 = 30.83 kN

Answer

RA = 30.83 kN
4.Beam support reactions

Answer: RA = 17.5 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.

w = 10 kN/mP = 30 kNABRA​RB​1 m1 m2 m2 m

Free-body diagram

Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.

Equilibrium

Moments about A, counter-clockwise positive. Then vertical force balance.

UDL resultant: W = w·ℓ = 10·1 = 10 kN, acting at x̄ = 1.5 m
ΣMA = 0: RB·6 = 30·4 + 10·1·1.5
RB = 135/6 = 22.5 kN
ΣFy = 0: RA = 40 − 22.5 = 17.5 kN

Answer

RA = 17.5 kN
5.Truss: method of joints

Answer: FBC = −28.84 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB40 kNAy​Cy​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·5 = 40·3 → Cy = 24 kN
ΣFy = 0: Ay = 40 − 24 = 16 kN

Joint C

The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.

sin γ = 3/3.606 = 0.8321, cos γ = 2/3.606 = 0.5547
ΣFy = 0: Cy + FBC·sin γ = 0 → FBC = −24/0.8321 = −28.84 kN

Answer

FBC = −28.84 kN (compression)
6.Truss: method of joints

Answer: FAC = 14.44 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB25 kN5 kNAy​Cy​Ax​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·6 = 25·2 + 5·3 → Cy = 10.83 kN
ΣFy = 0: Ay = 25 − 10.83 = 14.17 kN
ΣFx = 0: Ax = −5 kN

Joint C

The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.

sin γ = 3/5 = 0.6, cos γ = 4/5 = 0.8
ΣFy = 0: Cy + FBC·sin γ = 0 → FBC = −10.83/0.6 = −18.06 kN
ΣFx = 0: −FAC − FBC·cos γ = 0 → FAC = −(−18.06)·0.8 = 14.44 kN

Answer

FAC = 14.44 kN (tension)
7.Frames & machines

Answer: C = 2.828 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Tie force from leg BC

By = 2 kN
T = 2·2.4/2.4 = 2 kN

Components of the pin force on BC

Cx = T = 2 kN, Cy = −By = −2 kN

Magnitude

C = √(2² + 2²) = 2.828 kN

Answer

C = 2.828 kN
8.Frames & machines

Answer: FCD = 14.01 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Resultant of the uniform load

w·L = 1·2.5 = 2.5 kN at 1.25 m

Moments about A for the beam

FCD·0.6247·1.5 = 2.5·1.25 + 4·2.5 = 13.13 kN·m
FCD = 14.01 kN

Answer

FCD = 14.01 kN
9.Shear force & bending moment

Answer: Vx = −21.25 kN

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.

Support reactions

Equilibrium of the whole beam. The overhang load also acts about A.

ΣMA = 0: RB·4 = 40·1 + 45·5
RB = 265/4 = 66.25 kN
ΣFy = 0: RA = 85 − 66.25 = 18.75 kN

Cut just left of B and keep the left part

Vx = RA − P1 = 18.75 − 40 = −21.25 kN

Answer

Vx = −21.25 kN
10.Shear force & bending moment

Answer: Mmax = 168.8 kN·m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut. Maximum moment: since dM/dx = V, the bending moment has its peak where the shear force passes through zero, either at a point load or inside a distributed load.

Support reactions

Equilibrium of the whole beam.

UDL resultant: W = w·ℓ = 24·6 = 144 kN, acting at x̄ = 3 m
ΣMA = 0: RB·8 = 24·6·3
RB = 432/8 = 54 kN
ΣFy = 0: RA = 144 − 54 = 90 kN

Zero shear

The shear force starts at RA, stays constant over any unloaded part and falls with slope w inside the load.

RA − w·(x0 − 0) = 0
x0 = 0 + 90/24 = 3.75 m

Maximum moment

Mmax = RA·x0 − w·(x0 − 0)²/2 = 90·3.75 − 24·3.75²/2 = 168.8 kN·m

Answer

Mmax = 168.8 kN·m
11.Centroid & second moment of area

Answer: r = 29.13 mm

Second moment of area: for a rectangle about its own centroidal axis I = bh³/12, and about its base bh³/3 (parallel-axis theorem I = Ic + A·d²). A hole is handled by subtracting its I, as long as both parts share the same axis. The elastic section modulus is S = I/c, where c is the distance to the extreme fibre. The radius of gyration r = √(I/A) is the distance at which the whole area would give the same I; it is used in column buckling.

Net area and second moment of area

A = π(D² − d²)/4 = 2061 mm²
I = π(D⁴ − d⁴)/64 = 1.749 × 10⁶ mm⁴

Radius of gyration

r = √(I/A) = √(1.749 × 10⁶/2061) = 29.13 mm

Answer

r = 29.13 mm
12.Centroid & second moment of area

Answer: σmax = 38.94 MPa

Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.

Outer rectangle minus the two side cut-outs

Both cut-outs together are (B − tw) wide and hw = H − 2tf high, and share the axis x.

hw = 400 − 2·18 = 364 mm
Ix = (B·H³ − (B − tw)·hw³)/12 = (210·400³ − 202·364³)/12
Ix = 3.082 × 10⁸ mm⁴

Bending stress

y = 200 mm
σ = M·y/I = 6 × 10⁷·200/3.082 × 10⁸ = 38.94 MPa

Answer

σmax = 38.94 MPa

ExamProblems · examproblems.com/courses/statics