The bell crank shown turns about the pin O. A vertical force of 150 N at A (100 mm from O) is balanced by a horizontal force at B (100 mm above O). Find the magnitude of the pin reaction FO.
F = 150 NOA = 100 mmOB = 100 mm
FO = N
8.Frames & machinesHard
The A-frame shown stands on a pin at A and a roller at B, 2.4 m apart, with its apex pin C 3 m high and the horizontal tie DE 1.2 m above the ground. A vertical load of 10 kN acts on leg AC at K, 0.9 m (horizontally) from A. Find the magnitude of the force C that the pin C exerts on leg BC.
P = 10 kNAB = 2.4 mheight of C = 3 mheight of DE = 1.2 mhorizontal distance A to K = 0.9 m
C = kN
9.Shear force & bending momentMedium
The beam rests on a pin at A and a roller at B and overhangs B by 1.5 m to the free end C. It carries a point load P1 between the supports and a point load P2 at C. Find the bending moment Mx under the load P1. Use sagging moments positive and upward shear on the left face positive.
L = 5.5 mP1 = 45 kN at 2.5 mP2 = 40 kN at 5.5 msupports at x = 0 and x = 4 m
Mx = kN·m
10.Shear force & bending momentHard
The marks A to G split the beam into six equal parts. At which mark is the bending moment largest in size, sagging or hogging? Click it in the diagram.
45 kN @ 0 m50 kN @ 6 m20 kN @ 3 m15 kN/m, 1–5 m
1A (x = 0 m)
2B (x = 1 m)
3C (x = 2 m)
4D (x = 3 m)
5E (x = 4 m)
6F (x = 5 m)
7G (x = 6 m)
11.Centroid & second moment of areaMedium
A hollow rectangular (box) section has outer width B = 220 mm, outer height H = 400 mm and a uniform wall thickness t = 8 mm. Find its radius of gyration r about the horizontal centroidal axis.
B = 220 mmH = 400 mmt = 8 mm
r = mm
12.Centroid & second moment of areaHard
The T-section is used as a beam with the flange on top and carries a sagging bending moment of 5 kN·m. Find the size of the bending stress σtop at the top edge.
Dot product:a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.
Dot product
a·b = 3·4 + (−5)·1 + (−2)·(−2) = 11
Length of b
|b| = √(4² + 1² + (−2)²) = 4.583
Scalar projection
compb a = a·b/|b| = 11/4.583 = 2.4
Answer
compb a = 2.4
2.Vectors: dot & cross product
Answer: V = 30
Cross product:a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.
Cross product b × c
(b × c)x = bycz − bzcy = (−1)·(−2) − 5·4 = −18
(b × c)y = bzcx − bxcz = 5·(−4) − (−5)·(−2) = −30
(b × c)z = bxcy − bycx = (−5)·4 − (−1)·(−4) = −24
Dot product with a
a·(b × c) = 2·(−18) + (−3)·(−30) + 1·(−24) = 30
V = |30| = 30
Answer
V = 30
3.Beam support reactions
Answer: RB = 52.5 kN
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.
Free-body diagram
Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.
Equilibrium
Moments about A, counter-clockwise positive. Then vertical force balance.
ΣMA = 0: RB·4 = 45·1 + 55·3
RB = 210/4 = 52.5 kN
ΣFy = 0: RA = 100 − 52.5 = 47.5 kN
Answer
RB = 52.5 kN
4.Beam support reactions
Answer: RA = 41.88 kN
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.
Free-body diagram
Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.
Equilibrium
Moments about A, counter-clockwise positive. Then vertical force balance.
UDL resultant: W = w·ℓ = 2·1 = 2 kN, acting at x̄ = 5.5 m
ΣMA = 0: RB·8 = 55·2 + 2·1·5.5
RB = 121/8 = 15.13 kN
ΣFy = 0: RA = 57 − 15.13 = 41.88 kN
Answer
RA = 41.88 kN
5.Truss: method of joints
Answer: FAC = 8.75 kN
Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.
Support reactions
Equilibrium of the whole truss. Moments about A, counter-clockwise positive.
ΣMA = 0: Cy·8 = 30·7 → Cy = 26.25 kN
ΣFy = 0: Ay = 30 − 26.25 = 3.75 kN
Joint C
The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.
sin γ = 3/3.162 = 0.9487, cos γ = 1/3.162 = 0.3162
Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.
Joint D
CD and DE lie on one straight line and the joint carries no load. Balancing forces across that line leaves only DH.
ΣF⊥ = 0 → FDH = 0
Check with the method of joints
Solving all joints gives these member forces (T = tension, C = compression).
Machines: pliers, levers, linkages and clamps turn an input force into a larger or a differently directed output force. Draw one part as a free body and take moments about its pivot: the pin force drops out, and Fin·a = Fout·b gives the mechanical advantage a/b. The pin force then follows from ΣF = 0 on the same part. In a toggle, two links meet at a shallow angle θ; each link is a two-force member, so a small force F at the joint creates large link forces F/(2 sin θ) and a clamping force F/(2 tan θ).
Force at B
Q = 150·100/100 = 150 N
Pin reaction
Ox = 150 N, Oy = 150 N
FO = √(150² + 150²) = 212.1 N
Answer
FO = 212.1 N
8.Frames & machines
Answer: C = 4.507 kN
Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.
Support reaction at B
By = 10·0.9/2.4 = 3.75 kN
Tie force
T = 3.75·1.2/1.8 = 2.5 kN
Pin force on BC
Cx = 2.5 kN, Cy = −3.75 kN
C = √(2.5² + 3.75²) = 4.507 kN
Answer
C = 4.507 kN
9.Shear force & bending moment
Answer: Mx = 4.688 kN·m
Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.
Support reactions
Equilibrium of the whole beam. The overhang load also acts about A.
ΣMA = 0: RB·4 = 45·2.5 + 40·5.5
RB = 332.5/4 = 83.13 kN
ΣFy = 0: RA = 85 − 83.13 = 1.875 kN
Cut under P1 and keep the left part
Mx = RA·2.5 = 1.875·2.5 = 4.688 kN·m
Answer
Mx = 4.688 kN·m
10.Shear force & bending moment
Answer: F (x = 5 m)
Largest bending moment: M changes slope wherever the shear force changes, so its peaks sit where the shear force crosses zero: under a point load, inside a distributed load, or over a support of an overhang. At a fixed support of a cantilever the moment is largest at the wall. Compare the size of M at those places, sagging or hogging.
Support reactions
Take moments about one support, then use the vertical force balance.
R1 = 83.75 kN, R2 = 91.25 kN
Bending moment at every mark
Sum the moments of all forces on one side of the cut. Sagging is positive, hogging negative.
MA = 0, MB = −45, MC = −13.75, MD = 2.5, ME = −16.25, MF = −50 kN·m, MG = 0
Answer
Mark F: MF = −50 kN·m
11.Centroid & second moment of area
Answer: r = 147.7 mm
Second moment of area: for a rectangle about its own centroidal axis I = bh³/12, and about its base bh³/3 (parallel-axis theorem I = Ic + A·d²). A hole is handled by subtracting its I, as long as both parts share the same axis. The elastic section modulus is S = I/c, where c is the distance to the extreme fibre. The radius of gyration r = √(I/A) is the distance at which the whole area would give the same I; it is used in column buckling.
Net area and second moment of area
b = 204 mm, h = 384 mm
A = BH − bh = 220·400 − 204·384 = 9664 mm²
I = (BH³ − bh³)/12 = 2.107 × 10⁸ mm⁴
Radius of gyration
r = √(I/A) = √(2.107 × 10⁸/9664) = 147.7 mm
Answer
r = 147.7 mm
12.Centroid & second moment of area
Answer: σtop = 8.576 MPa
Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.
Split into two rectangles
Measure every y from the bottom edge.
flange: Af = 300·15 = 4500 mm², yf = 200 + 15/2 = 207.5 mm