In the print window, choose “Save as PDF” to keep a copy on your device.
1Formulas and methods
Vectors: dot & cross product
Magnitude
|a| = √(ax² + ay² + az²)
Unit vector
û = a/|a|
Components from an angle
Fx = F·cos θ, Fy = F·sin θ
Dot product
a·b = axbx + ayby + azbz = |a||b|cos θ
Scalar projection of a onto b
a·b/|b|
Work
W = F·d
Cross product
a × b = (aybz − azby, azbx − axbz, axby − aybx)
Areas
parallelogram |a × b|, triangle ½|a × b|
Moment about O
MO = r × F, r = A − O
Volume of a parallelepiped
V = |a·(b × c)|
Method
Write every vector in components; for a force given by a magnitude and an angle, use F·cos θ and F·sin θ.
For lengths and directions use the magnitude √(x² + y² + z²) and the unit vector a/|a|.
Use the dot product for angles, projections, perpendicularity and work: a·b = |a||b|cos θ.
Use the cross product for perpendicular vectors, areas and moments: write the three components carefully, keeping the order a × b.
Beam support reactions
Equilibrium
ΣFx = 0, ΣFy = 0, ΣM = 0
Uniform load
resultant w·L at the middle of the load
Moment
M = F·d
Method
Draw a free-body diagram and replace each support by its reactions.
Replace every distributed load by a single force at its centroid.
Take moments about one support to find the reaction at the other.
Use ΣFy = 0 to find the remaining reaction, and check with a second moment equation.
Truss: method of joints
Method of joints
ΣFx = 0, ΣFy = 0 at each joint
Method of sections
ΣM = 0 about a cut point
Member force
positive = tension, negative = compression
Method
Find the support reactions for the whole truss.
Method of joints: start at a joint with at most two unknown member forces and use ΣFx = 0 and ΣFy = 0.
Method of sections: cut through the member you need and take moments about a point where the other unknown members meet.
Assume tension; a negative answer means compression.
Frames & machines
Equilibrium of each member
ΣFx = 0, ΣFy = 0, ΣM = 0
Two-force member
force along the line through its two pins
Pin force
equal and opposite on the two members it joins
Magnitude of a pin force
F = √(Fx² + Fy²)
Lever, pliers, bell crank
Fin·a = Fout·b
Toggle
Flink = F/(2 sin θ), Q = F/(2 tan θ)
Uniform load
resultant w·L at the middle of the load
Method
Draw the whole structure and find the support reactions if there are no more than three unknowns.
Spot the two-force members: loaded only at two pins, their force acts along the line between the pins.
Take the frame apart and draw every member on its own, with equal and opposite pin forces where members meet.
For each member, take moments about a pin with unknown forces, then use ΣFx = 0 and ΣFy = 0; combine components into a magnitude at the end.
Shear force & bending moment
Shear and moment
V = ΣF on one side, M = ΣF·d on one side
Bending stress
σ = M·y/I
Rectangle
I = bh³/12
Section modulus
W = I/ymax
Simply supported, uniform load
Mmax = wL²/8
Method
Find the support reactions from equilibrium of the whole beam.
Cut the beam at the section you need and keep one side.
Shear force: sum of the vertical forces on that side. Bending moment: sum of their moments about the cut.
For the maximum moment, find where the shear force is zero.
Centroid & second moment of area
Centroid
ȳ = ΣAiyi/ΣAi
Rectangle
I = bh³/12
Parallel-axis theorem
I = Ic + A·d²
Composite section
I = Σ(Ic,i + Aidi²)
2Practice problems
1.Vectors: dot & cross productMedium
Find the dot product a·b of a = (7, −3, 7) and b = (−7, 0, −4).
a = (7, −3, 7)b = (−7, 0, −4)
a·b =
2.Vectors: dot & cross productHard
A force F = (60, 50, 40) N acts at point A(−2, −1, 0). Coordinates are in metres. Find the z-component Mz of the moment of the force about point O(2, 3, −2).
F = (60, 50, 40) NA(−2, −1, 0) mO(2, 3, −2) m
Mz = N·m
3.Beam support reactionsMedium
The simply supported beam has a pin at A and a roller at B. Find the vertical support reaction RA.
L = 4 mP1 = 45 kN at 1 mP2 = 10 kN at 3 m
RA = kN
4.Beam support reactionsHard
The beam has a pin at A and a roller at B, 8 m from A, and overhangs B to the free end C. It carries a point load P at 1 m from A and a uniformly distributed load w from 7 m to the free end at 10 m. Find the vertical reaction RB, taking upward as positive.
AB = 8 mAC = 10 mP = 60 kN at 1 mw = 3 kN/m from 7 to 10 m
RB = kN
5.Truss: method of jointsMedium
Exactly one member of this truss carries no force under these loads. Which is the zero-force member? Click it in the diagram.
D: 30 kN ↓F: 40 kN ↓
1member AB
2member BC
3member CD
4member DE
5member FG
6member GH
7member AF
8member HE
9member BF
10member CG
11member DH
12member BG
13member DG
6.Truss: method of jointsHard
Exactly one member of this truss carries no force under these loads. Which is the zero-force member? Click it in the diagram.
The frame shown has pins at A, B and C; A and C are fixed to the ground 3 m apart, and B is 2 m above the ground and 1.35 m to the right of A. A vertical load of 20 kN acts on member AB at K, 0.54 m (horizontally) from A. Find the force FBC in member BC.
P = 20 kNL = 3 mH = 2 mhorizontal distance A to B = 1.35 mhorizontal distance A to K = 0.54 m
FBC = kN
8.Frames & machinesHard
A uniform horizontal boom AB of weight 2 kN is pinned to a wall at A and held by a cable from its end B to the point C on the wall, 1.5 m above A. A load of 4 kN hangs at B. Find the tension T in the cable.
W = 4 kNWb = 2 kNAB = 6 mAC = 1.5 m
T = kN
9.Shear force & bending momentMedium
The beam rests on a pin at A and a roller at B and overhangs B by 1.5 m to the free end C. It carries a point load P1 between the supports and a point load P2 at C. Find the bending moment Mx under the load P1. Use sagging moments positive and upward shear on the left face positive.
L = 5.5 mP1 = 50 kN at 2 mP2 = 20 kN at 5.5 msupports at x = 0 and x = 4 m
Mx = kN·m
10.Shear force & bending momentHard
The beam rests on a pin at A and a roller at B and overhangs B by 2 m to the free end C. A uniformly distributed load w acts over the whole length A–C. Find the maximum sagging bending moment Mmax between the supports.
L = 8 mw = 5 kN/m from 0 to 8 msupports at x = 0 and x = 6 m
Mmax = kN·m
11.Centroid & second moment of areaMedium
A channel section lies with its open side up: a base plate 160 mm wide with two upright legs, 140 mm high overall. Base and legs are all 20 mm thick. Find the height ȳ of the centroid above the bottom edge.
b = 160 mmh = 140 mmt = 20 mm
ȳ = mm
12.Centroid & second moment of areaHard
A symmetric I-section has flanges 120 mm wide and 18 mm thick, an overall depth of 200 mm and a web 6 mm thick. It carries a bending moment of 30 kN·m about the axis x. Find the size of the bending stress σj at the junction of the web and the top flange.
Dot product:a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.
Negative: the angle between the vectors is more than 90°.
2.Vectors: dot & cross product
Answer: Mz = 40 N·m
Cross product:a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.
Position vector from O to A
r = A − O = (−2, −1, 0) − (2, 3, −2) = (−4, −4, 2) m
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.
Free-body diagram
Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.
Equilibrium
Moments about A, counter-clockwise positive. Then vertical force balance.
ΣMA = 0: RB·4 = 45·1 + 10·3
RB = 75/4 = 18.75 kN
ΣFy = 0: RA = 55 − 18.75 = 36.25 kN
Answer
RA = 36.25 kN
4.Beam support reactions
Answer: RB = 17.06 kN
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Replace each distributed load by its resultant (its area) acting at the centroid of the load diagram, and take moments about a support to remove that support’s reaction from the equation.
Resultant of the distributed load
W = 3·3 = 9 kN, x̄ = (7 + 10)/2 = 8.5 m
Equilibrium
Moments about A, counter-clockwise positive. Then vertical force balance.
ΣMA = 0: RB·8 = 60·1 + 9·8.5
RB = 136.5/8 = 17.06 kN
RA = 69 − 17.06 = 51.94 kN
Answer
RB = 17.06 kN
5.Truss: method of joints
Answer: member CG
Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.
Joint C
BC and CD lie on one straight line and the joint carries no load. Balancing forces across that line leaves only CG.
ΣF⊥ = 0 → FCG = 0
Check with the method of joints
Solving all joints gives these member forces (T = tension, C = compression).
Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.
Joint G
FG and GH lie on one straight line and the joint carries no load. Balancing forces across that line leaves only CG.
ΣF⊥ = 0 → FCG = 0
Check with the method of joints
Solving all joints gives these member forces (T = tension, C = compression).
Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.
Two-force member BC
BC = √(1.65² + 2²) = 2.593 m
Whole frame: moments about A
The ground pushes on BC at C along CB; its horizontal component passes through A, only the vertical one has a moment.
FBC·(2/2.593)·3 = 20·0.54
FBC = 4.667 kN (compression)
Answer
FBC = 4.667 kN
8.Frames & machines
Answer: T = 20.62 kN
Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.
Cable angle
BC = √(6² + 1.5²) = 6.185 m, sin β = 0.2425
Moments about A
T·0.2425·6 = 4·6 + 2·3
T = 20.62 kN
Answer
T = 20.62 kN
9.Shear force & bending moment
Answer: Mx = 35 kN·m
Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.
Support reactions
Equilibrium of the whole beam. The overhang load also acts about A.
ΣMA = 0: RB·4 = 50·2 + 20·5.5
RB = 210/4 = 52.5 kN
ΣFy = 0: RA = 70 − 52.5 = 17.5 kN
Cut under P1 and keep the left part
Mx = RA·2 = 17.5·2 = 35 kN·m
Answer
Mx = 35 kN·m
10.Shear force & bending moment
Answer: Mmax = 17.78 kN·m
Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut. Maximum moment: since dM/dx = V, the bending moment has its peak where the shear force passes through zero, either at a point load or inside a distributed load.
Support reactions
Equilibrium of the whole beam, including the load on the overhang.
UDL resultant: W = w·ℓ = 5·8 = 40 kN, acting at x̄ = 4 m
Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.
Split into rectangles
Take the base at full width and the two legs above it (height h − t), so nothing is counted twice.
base: A1 = 160·20 = 3200 mm², y1 = 10 mm
two legs: A2 = 2·20·120 = 4800 mm², y2 = 20 + 120/2 = 80 mm
Centroid
ȳ = (3200·10 + 4800·80)/8000 = 52 mm
Answer
ȳ = 52 mm
12.Centroid & second moment of area
Answer: σj = 64.57 MPa
Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.
Outer rectangle minus the two side cut-outs
Both cut-outs together are (B − tw) wide and hw = H − 2tf high, and share the axis x.