Statics: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Vectors: dot & cross product

Magnitude
|a| = √(ax² + ay² + az²)
Unit vector
û = a/|a|
Components from an angle
Fx = F·cos θ, Fy = F·sin θ
Dot product
a·b = axbx + ayby + azbz = |a||b|cos θ
Scalar projection of a onto b
a·b/|b|
Work
W = F·d
Cross product
a × b = (aybz − azby, azbx − axbz, axby − aybx)
Areas
parallelogram |a × b|, triangle ½|a × b|
Moment about O
MO = r × F, r = A − O
Volume of a parallelepiped
V = |a·(b × c)|

Method

  1. Write every vector in components; for a force given by a magnitude and an angle, use F·cos θ and F·sin θ.
  2. For lengths and directions use the magnitude √(x² + y² + z²) and the unit vector a/|a|.
  3. Use the dot product for angles, projections, perpendicularity and work: a·b = |a||b|cos θ.
  4. Use the cross product for perpendicular vectors, areas and moments: write the three components carefully, keeping the order a × b.

Beam support reactions

Equilibrium
ΣFx = 0, ΣFy = 0, ΣM = 0
Uniform load
resultant w·L at the middle of the load
Moment
M = F·d

Method

  1. Draw a free-body diagram and replace each support by its reactions.
  2. Replace every distributed load by a single force at its centroid.
  3. Take moments about one support to find the reaction at the other.
  4. Use ΣFy = 0 to find the remaining reaction, and check with a second moment equation.

Truss: method of joints

Method of joints
ΣFx = 0, ΣFy = 0 at each joint
Method of sections
ΣM = 0 about a cut point
Member force
positive = tension, negative = compression

Method

  1. Find the support reactions for the whole truss.
  2. Method of joints: start at a joint with at most two unknown member forces and use ΣFx = 0 and ΣFy = 0.
  3. Method of sections: cut through the member you need and take moments about a point where the other unknown members meet.
  4. Assume tension; a negative answer means compression.

Frames & machines

Equilibrium of each member
ΣFx = 0, ΣFy = 0, ΣM = 0
Two-force member
force along the line through its two pins
Pin force
equal and opposite on the two members it joins
Magnitude of a pin force
F = √(Fx² + Fy²)
Lever, pliers, bell crank
Fin·a = Fout·b
Toggle
Flink = F/(2 sin θ), Q = F/(2 tan θ)
Uniform load
resultant w·L at the middle of the load

Method

  1. Draw the whole structure and find the support reactions if there are no more than three unknowns.
  2. Spot the two-force members: loaded only at two pins, their force acts along the line between the pins.
  3. Take the frame apart and draw every member on its own, with equal and opposite pin forces where members meet.
  4. For each member, take moments about a pin with unknown forces, then use ΣFx = 0 and ΣFy = 0; combine components into a magnitude at the end.

Shear force & bending moment

Shear and moment
V = ΣF on one side, M = ΣF·d on one side
Bending stress
σ = M·y/I
Rectangle
I = bh³/12
Section modulus
W = I/ymax
Simply supported, uniform load
Mmax = wL²/8

Method

  1. Find the support reactions from equilibrium of the whole beam.
  2. Cut the beam at the section you need and keep one side.
  3. Shear force: sum of the vertical forces on that side. Bending moment: sum of their moments about the cut.
  4. For the maximum moment, find where the shear force is zero.

Centroid & second moment of area

Centroid
ȳ = ΣAiyi/ΣAi
Rectangle
I = bh³/12
Parallel-axis theorem
I = Ic + A·d²
Composite section
I = Σ(Ic,i + Aidi²)

2Practice problems

1.Vectors: dot & cross productMedium
xyzab

Find the scalar projection compb a of a = (1, −6, −4) onto b = (3, 0, −5), that is, the component of a in the direction of b.

a = (1, −6, −4)b = (3, 0, −5)
compb a =
2.Vectors: dot & cross productHard
xyzABC

Find the area A of the triangle with corners A(3, −1, −2), B(−1, −3, 0) and C(4, 4, 4). Coordinates are in metres.

A(3, −1, −2)B(−1, −3, 0)C(4, 4, 4)
A = m²
3.Beam support reactionsMedium
P1​ = 50 kNP2​ = 30 kNABCRA​ = ?0.5 m2.5 m2 m

The beam has a pin at A and a roller at B, 3 m from A, and overhangs B to the free end C. Find the vertical reaction RA, taking upward as positive.

AB = 3 mAC = 5 mP1 = 50 kN at 0.5 mP2 = 30 kN at 5 m
RA = kN
4.Beam support reactionsHard
w0​ = 8 kN/mP = 70 kNABMA​ = ?2 m4 m

The cantilever beam is fixed to the wall at A. It carries a linearly varying load that is 8 kN/m at the wall and falls to zero at the free end B, plus a point load P at 2 m from the wall. Find the magnitude of the reaction moment MA at the wall.

L = 6 mw0 = 8 kN/mP = 70 kN at 2 m
MA = kN·m
5.Truss: method of jointsMedium
ABBCACACB45 kN5 m1 m3 m

Use the method of joints to find the force FAC in member AC. Give tension as positive and compression as negative.

span = 5 mheight = 3 mB is 1 m from Avertical load = 45 kN
FAC = kN
6.Truss: method of jointsHard
ABBCACACB50 kN15 kN4 m1 m2 m

Use the method of joints to find the force FAC in member AC. Give tension as positive and compression as negative.

span = 4 mheight = 2 mB is 1 m from Avertical load = 50 kNhorizontal load = 15 kN ←
FAC = kN
7.Frames & machinesMedium
15 kN4.8 m0.6 m1.9 mABCDE

The A-frame shown stands on a pin at A and a roller at B, 4.8 m apart. The legs meet at the pin C, 2.5 m high, and the horizontal tie DE is 0.6 m above the ground. A load of 15 kN acts at C. Find the magnitude of the force C that the pin C exerts on leg BC.

P = 15 kNAB = 4.8 mheight of C = 2.5 mheight of DE = 0.6 m
C = kN
8.Frames & machinesHard
w = 4 kN/m6 kN1.2 m1.3 m1 mABCD

The beam AB of the wall bracket shown is pinned at A and propped by the strut CD (C is 1 m below A). The beam carries a uniform load of 4 kN/m over its full length and a point load of 6 kN at its free end B. Find the force FCD in the strut.

w = 4 kN/mP = 6 kNAD = 1.2 mAB = 2.5 mAC = 1 m
FCD = kN
9.Shear force & bending momentMedium
30 kN60 kNABCDEFG1 m1 m1 m1 m1 m1 m

The marks A to G split the beam into six equal parts. At which mark is the bending moment largest in size, sagging or hogging? Click it in the diagram.

30 kN @ 2 m60 kN @ 3 m
  1. 1A (x = 0 m)
  2. 2B (x = 1 m)
  3. 3C (x = 2 m)
  4. 4D (x = 3 m)
  5. 5E (x = 4 m)
  6. 6F (x = 5 m)
  7. 7G (x = 6 m)
10.Shear force & bending momentHard
w = 3 kN/mP = 50 kNABsection4 m6 m

Find the bending moment Mx at the section x = 4 m from support A. Use sagging moments positive and upward shear on the left face positive.

L = 10 mP = 50 kN at 4 mw = 3 kN/m from 0 to 10 mx = 4 m
Mx = kN·m
11.Centroid & second moment of areaMedium
2404602210xdimensions in mm

A symmetric I-section has flanges 240 mm wide and 22 mm thick, an overall depth of 460 mm and a web 10 mm thick. Find its elastic section modulus Sx for bending about the horizontal centroidal axis x.

B = 240 mmH = 460 mmtf = 22 mmtw = 10 mm
Sx = × 10³ mm³
12.Centroid & second moment of areaHard
150 mm150 mm105 mm80 × 50xIx​ = ?

A 150 mm × 150 mm plate has a rectangular cut-out 80 mm wide and 50 mm high, centred on the vertical centre line with its centre 105 mm above the bottom. Find the second moment of area Ix about the horizontal axis through the centroid.

b = 150 mmh = 150 mmcut-out: 80 × 50 mmhole centre: y = 105 mm
Ix = × 10⁶ mm⁴

3Solutions

1.Vectors: dot & cross product

Answer: compb a = 3.944

Dot product: a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.

Dot product

a·b = 1·3 + (−6)·0 + (−4)·(−5) = 23

Length of b

|b| = √(3² + 0² + (−5)²) = 5.831

Scalar projection

compb a = a·b/|b| = 23/5.831 = 3.944

Answer

compb a = 3.944
2.Vectors: dot & cross product

Answer: A = 19.26 m²

Cross product: a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.

Edge vectors

AB = B − A = (−4, −2, 2)
AC = C − A = (1, 5, 6)

Cross product

(AB × AC)x = AByACz − ABzACy = (−2)·6 − 2·5 = −22
(AB × AC)y = ABzACx − ABxACz = 2·1 − (−4)·6 = 26
(AB × AC)z = ABxACy − AByACx = (−4)·5 − (−2)·1 = −18
|AB × AC| = √((−22)² + 26² + (−18)²) = 38.52

Area of the triangle

A = ½·38.52 = 19.26 m²

Answer

A = 19.26 m²
3.Beam support reactions

Answer: RA = 21.67 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Replace each distributed load by its resultant (its area) acting at the centroid of the load diagram, and take moments about a support to remove that support’s reaction from the equation.

Moments about A

Counter-clockwise positive.

ΣMA = 0: RB·3 = 50·0.5 + 30·5
RB = 175/3 = 58.33 kN

Vertical equilibrium

RA = 50 + 30 − 58.33 = 21.67 kN

Answer

RA = 21.67 kN
4.Beam support reactions

Answer: MA = 188 kN·m

Cantilever equilibrium: a fixed support can push up and also resist rotation, so it gives a vertical reaction RA and a reaction moment MA. ΣFy = 0 gives RA, and moments about the wall give MA = Σ(load × distance from the wall). A distributed load acts as its resultant at the centroid of the load diagram.

Resultant of the triangular load

W = ½·8·6 = 24 kN
x̄ = L/3 = 2 m

Moment about the wall

MA = W·x̄ + P·a = 24·2 + 70·2 = 188 kN·m

Answer

MA = 188 kN·m
5.Truss: method of joints

Answer: FAC = 12 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB45 kNAy​Cy​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·5 = 45·1 → Cy = 9 kN
ΣFy = 0: Ay = 45 − 9 = 36 kN

Joint C

The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.

sin γ = 3/5 = 0.6, cos γ = 4/5 = 0.8
ΣFy = 0: Cy + FBC·sin γ = 0 → FBC = −9/0.6 = −15 kN
ΣFx = 0: −FAC − FBC·cos γ = 0 → FAC = −(−15)·0.8 = 12 kN

Answer

FAC = 12 kN (tension)
6.Truss: method of joints

Answer: FAC = 7.5 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB50 kN15 kNAy​Cy​Ax​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·4 = 50·1 − 15·2 → Cy = 5 kN
ΣFy = 0: Ay = 50 − 5 = 45 kN
ΣFx = 0: Ax = 15 kN

Joint C

The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.

sin γ = 2/3.606 = 0.5547, cos γ = 3/3.606 = 0.8321
ΣFy = 0: Cy + FBC·sin γ = 0 → FBC = −5/0.5547 = −9.014 kN
ΣFx = 0: −FAC − FBC·cos γ = 0 → FAC = −(−9.014)·0.8321 = 7.5 kN

Answer

FAC = 7.5 kN (tension)
7.Frames & machines

Answer: C = 12.08 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Tie force from leg BC

By = 7.5 kN
T = 7.5·2.4/1.9 = 9.474 kN

Components of the pin force on BC

Cx = T = 9.474 kN, Cy = −By = −7.5 kN

Magnitude

C = √(9.474² + 7.5²) = 12.08 kN

Answer

C = 12.08 kN
8.Frames & machines

Answer: FCD = 35.8 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Resultant of the uniform load

w·L = 4·2.5 = 10 kN at 1.25 m

Moments about A for the beam

FCD·0.6402·1.2 = 10·1.25 + 6·2.5 = 27.5 kN·m
FCD = 35.8 kN

Answer

FCD = 35.8 kN
9.Shear force & bending moment

Answer: D (x = 3 m)

Largest bending moment: M changes slope wherever the shear force changes, so its peaks sit where the shear force crosses zero: under a point load, inside a distributed load, or over a support of an overhang. At a fixed support of a cantilever the moment is largest at the wall. Compare the size of M at those places, sagging or hogging.

Support reactions

Take moments about one support, then use the vertical force balance.

R1 = 50 kN, R2 = 40 kN

Bending moment at every mark

Sum the moments of all forces on one side of the cut. Sagging is positive, hogging negative.

MA = 0, MB = 50, MC = 100, MD = 120 kN·m, ME = 80, MF = 40, MG = 0

Answer

Mark D: MD = 120 kN·m
10.Shear force & bending moment

Answer: Mx = 156 kN·m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.

Support reactions

Equilibrium of the whole beam.

UDL resultant: W = w·ℓ = 3·10 = 30 kN, acting at x̄ = 5 m
ΣMA = 0: RB·10 = 50·4 + 3·10·5
RB = 350/10 = 35 kN
ΣFy = 0: RA = 80 − 35 = 45 kN
w = 3 kN/mP = 50 kNABRA​ = 45RB​ = 35section4 m6 m

Cut at x = 4 m and keep the left part

Only forces left of the cut appear. A UDL portion acts as one force at the middle of that portion.

M = RA·x − (each load left of the cut × its distance to the cut)
Mx = 45·4 − 3·4·2 = 156 kN·m

Answer

Mx = 156 kN·m
11.Centroid & second moment of area

Answer: Sx = 2465 × 10³ mm³

Second moment of area: for a rectangle about its own centroidal axis I = bh³/12, and about its base bh³/3 (parallel-axis theorem I = Ic + A·d²). A hole is handled by subtracting its I, as long as both parts share the same axis. The elastic section modulus is S = I/c, where c is the distance to the extreme fibre.

Outer rectangle minus the two side cut-outs

Both cut-outs together are (B − tw) wide and hw = H − 2tf high, and share the axis x.

hw = 460 − 2·22 = 416 mm
Ix = (B·H³ − (B − tw)·hw³)/12 = (240·460³ − 230·416³)/12
Ix = 5.669 × 10⁸ mm⁴

Section modulus

c = H/2 = 230 mm
Sx = I/c = 5.669 × 10⁸/230
Sx = 2.465 × 10⁶ mm³ = 2465 × 10³ mm³

Answer

Sx = 2465 × 10³ mm³
12.Centroid & second moment of area

Answer: Ix = 36.98 × 10⁶ mm⁴

Sections with holes: treat a hole as a negative area. The centroid is ȳ = (A₁y₁ − A₂y₂)/(A₁ − A₂), with A₁, y₁ for the full plate and A₂, y₂ for the hole. For the second moment of area about the centroidal axis, use the parallel-axis theorem for each part and subtract the hole: I = (Ic1 + A₁d₁²) − (Ic2 + A₂d₂²), where d is the distance from each part's own centroid to the axis through ȳ. A rectangle has Ic = bh³/12 and a circle Ic = πd⁴/64.

Centroid

ȳ = (22500·75 − 4000·105)/(22500 − 4000) = 68.51 mm

Full plate about ȳ

150·150³/12 + 22500·6.486² = 43.13 × 10⁶ mm⁴

Hole about ȳ

80·50³/12 + 4000·36.49² = 6.158 × 10⁶ mm⁴

Subtract

Ix = 36.98 × 10⁶ mm⁴

Answer

Ix = 36.98 × 10⁶ mm⁴

ExamProblems · examproblems.com/courses/statics