In the print window, choose “Save as PDF” to keep a copy on your device.
1Formulas and methods
Vectors: dot & cross product
Magnitude
|a| = √(ax² + ay² + az²)
Unit vector
û = a/|a|
Components from an angle
Fx = F·cos θ, Fy = F·sin θ
Dot product
a·b = axbx + ayby + azbz = |a||b|cos θ
Scalar projection of a onto b
a·b/|b|
Work
W = F·d
Cross product
a × b = (aybz − azby, azbx − axbz, axby − aybx)
Areas
parallelogram |a × b|, triangle ½|a × b|
Moment about O
MO = r × F, r = A − O
Volume of a parallelepiped
V = |a·(b × c)|
Method
Write every vector in components; for a force given by a magnitude and an angle, use F·cos θ and F·sin θ.
For lengths and directions use the magnitude √(x² + y² + z²) and the unit vector a/|a|.
Use the dot product for angles, projections, perpendicularity and work: a·b = |a||b|cos θ.
Use the cross product for perpendicular vectors, areas and moments: write the three components carefully, keeping the order a × b.
Beam support reactions
Equilibrium
ΣFx = 0, ΣFy = 0, ΣM = 0
Uniform load
resultant w·L at the middle of the load
Moment
M = F·d
Method
Draw a free-body diagram and replace each support by its reactions.
Replace every distributed load by a single force at its centroid.
Take moments about one support to find the reaction at the other.
Use ΣFy = 0 to find the remaining reaction, and check with a second moment equation.
Truss: method of joints
Method of joints
ΣFx = 0, ΣFy = 0 at each joint
Method of sections
ΣM = 0 about a cut point
Member force
positive = tension, negative = compression
Method
Find the support reactions for the whole truss.
Method of joints: start at a joint with at most two unknown member forces and use ΣFx = 0 and ΣFy = 0.
Method of sections: cut through the member you need and take moments about a point where the other unknown members meet.
Assume tension; a negative answer means compression.
Frames & machines
Equilibrium of each member
ΣFx = 0, ΣFy = 0, ΣM = 0
Two-force member
force along the line through its two pins
Pin force
equal and opposite on the two members it joins
Magnitude of a pin force
F = √(Fx² + Fy²)
Lever, pliers, bell crank
Fin·a = Fout·b
Toggle
Flink = F/(2 sin θ), Q = F/(2 tan θ)
Uniform load
resultant w·L at the middle of the load
Method
Draw the whole structure and find the support reactions if there are no more than three unknowns.
Spot the two-force members: loaded only at two pins, their force acts along the line between the pins.
Take the frame apart and draw every member on its own, with equal and opposite pin forces where members meet.
For each member, take moments about a pin with unknown forces, then use ΣFx = 0 and ΣFy = 0; combine components into a magnitude at the end.
Shear force & bending moment
Shear and moment
V = ΣF on one side, M = ΣF·d on one side
Bending stress
σ = M·y/I
Rectangle
I = bh³/12
Section modulus
W = I/ymax
Simply supported, uniform load
Mmax = wL²/8
Method
Find the support reactions from equilibrium of the whole beam.
Cut the beam at the section you need and keep one side.
Shear force: sum of the vertical forces on that side. Bending moment: sum of their moments about the cut.
For the maximum moment, find where the shear force is zero.
Centroid & second moment of area
Centroid
ȳ = ΣAiyi/ΣAi
Rectangle
I = bh³/12
Parallel-axis theorem
I = Ic + A·d²
Composite section
I = Σ(Ic,i + Aidi²)
2Practice problems
1.Vectors: dot & cross productMedium
A constant force F = (−30, 5, −15) N acts on an object while it moves in a straight line from point A(4, −3, −5) to point B(−4, −5, −2). Coordinates are in metres. Find the work W done by the force.
F = (−30, 5, −15) NA(4, −3, −5) mB(−4, −5, −2) m
W = J
2.Vectors: dot & cross productHard
A force F = (−10, −30, 50) N acts at point A(4, −2, 1). Coordinates are in metres. Find the z-component Mz of the moment of the force about the origin O(0, 0, 0).
F = (−10, −30, 50) NA(4, −2, 1) mO(0, 0, 0) m
Mz = N·m
3.Beam support reactionsMedium
The cantilever beam is fixed to the wall at A. It carries a uniformly distributed load w along its whole length and a point load P at 7 m from the wall. Find the magnitude of the reaction moment MA at the wall.
L = 8 mP = 45 kN at 7 mw = 3 kN/m from 0 to 8 m
MA = kN·m
4.Beam support reactionsHard
The cantilever beam is fixed to the wall at A. It carries a linearly varying load that is 20 kN/m at the wall and falls to zero at the free end B, plus a point load P at 4.5 m from the wall. Find the magnitude of the reaction moment MA at the wall.
L = 6 mw0 = 20 kN/mP = 45 kN at 4.5 m
MA = kN·m
5.Truss: method of jointsMedium
Exactly one member of this truss carries no force under these loads. Which is the zero-force member? Click it in the diagram.
D: 10 kN ↓F: 25 kN ↓G: 35 kN ↓
1member AB
2member BC
3member CD
4member DE
5member FG
6member GH
7member AF
8member HE
9member BF
10member CG
11member DH
12member FC
13member HC
6.Truss: method of jointsHard
Use the method of joints to find the force FBC in member BC. Give tension as positive and compression as negative.
span = 6 mheight = 4 mB is 1 m from Avertical load = 15 kNhorizontal load = 25 kN →
FBC = kN
7.Frames & machinesMedium
The A-frame shown stands on a pin at A and a roller at B, 6 m apart, with its apex pin C 3.6 m high and the horizontal tie DE 1.2 m above the ground. A vertical load of 5 kN acts on leg AC at K, 1.5 m (horizontally) from A. Find the tension T in the tie.
P = 5 kNAB = 6 mheight of C = 3.6 mheight of DE = 1.2 mhorizontal distance A to K = 1.5 m
T = kN
8.Frames & machinesHard
A uniform horizontal boom AB of weight 1 kN is pinned to a wall at A and held by a cable from B to the point C on the wall, 1.5 m above A. A load of 5 kN hangs at B. Find the magnitude of the pin reaction A.
W = 5 kNWb = 1 kNAB = 6 mAC = 1.5 m
A = kN
9.Shear force & bending momentMedium
The marks A to G split the beam into six equal parts. At which mark is the bending moment largest in size, sagging or hogging? Click it in the diagram.
50 kN @ 3 m6 kN/m, 0–6 m
1A (x = 0 m)
2B (x = 1 m)
3C (x = 2 m)
4D (x = 3 m)
5E (x = 4 m)
6F (x = 5 m)
7G (x = 6 m)
10.Shear force & bending momentHard
The beam rests on a pin at A and a roller at B and overhangs B by 1.5 m to the free end C. A uniformly distributed load w acts over the whole length A–C. Find the maximum sagging bending moment Mmax between the supports.
L = 9.5 mw = 3 kN/m from 0 to 9.5 msupports at x = 0 and x = 8 m
Mmax = kN·m
11.Centroid & second moment of areaMedium
A 200 mm × 240 mm plate has a circular hole of diameter 30 mm on its vertical centre line, with its centre 84 mm above the bottom. Find the second moment of area Ix about the horizontal axis through the centroid.
b = 200 mmh = 240 mmd = 30 mmhole centre: y = 84 mm
Ix = × 10⁶ mm⁴
12.Centroid & second moment of areaHard
A 100 mm × 150 mm plate has a rectangular cut-out 40 mm wide and 50 mm high, centred on the vertical centre line with its centre 60 mm above the bottom. Find the second moment of area Ix about the horizontal axis through the centroid.
b = 100 mmh = 150 mmcut-out: 40 × 50 mmhole centre: y = 60 mm
Ix = × 10⁶ mm⁴
3Solutions
1.Vectors: dot & cross product
Answer: W = 185 J
Dot product:a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.
Displacement
d = B − A = (−4, −5, −2) − (4, −3, −5) = (−8, −2, 3) m
Work
W = F·d = (−30)·(−8) + 5·(−2) + (−15)·3 = 185 J
Answer
W = 185 J
2.Vectors: dot & cross product
Answer: Mz = −140 N·m
Cross product:a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.
Cantilever equilibrium: a fixed support can push up and also resist rotation, so it gives a vertical reaction RA and a reaction moment MA. ΣFy = 0 gives RA, and moments about the wall give MA = Σ(load × distance from the wall). A distributed load acts as its resultant at the centroid of the load diagram.
Resultant of the distributed load
W = 3·8 = 24 kN, x̄ = 4 m
Moment about the wall
MA = P·a + W·x̄ = 45·7 + 24·4 = 411 kN·m
Answer
MA = 411 kN·m
4.Beam support reactions
Answer: MA = 322.5 kN·m
Cantilever equilibrium: a fixed support can push up and also resist rotation, so it gives a vertical reaction RA and a reaction moment MA. ΣFy = 0 gives RA, and moments about the wall give MA = Σ(load × distance from the wall). A distributed load acts as its resultant at the centroid of the load diagram.
Resultant of the triangular load
W = ½·20·6 = 60 kN
x̄ = L/3 = 2 m
Moment about the wall
MA = W·x̄ + P·a = 60·2 + 45·4.5 = 322.5 kN·m
Answer
MA = 322.5 kN·m
5.Truss: method of joints
Answer: member BF
Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.
Joint B
AB and BC lie on one straight line and the joint carries no load. Balancing forces across that line leaves only BF.
ΣF⊥ = 0 → FBF = 0
Check with the method of joints
Solving all joints gives these member forces (T = tension, C = compression).
Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.
Support reactions
Equilibrium of the whole truss. Moments about A, counter-clockwise positive.
ΣMA = 0: Cy·6 = 15·1 + 25·4 → Cy = 19.17 kN
ΣFy = 0: Ay = 15 − 19.17 = −4.167 kN
ΣFx = 0: Ax = −25 kN
Joint C
The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.
sin γ = 4/6.403 = 0.6247, cos γ = 5/6.403 = 0.7809
Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.
Whole frame: moments about A
By = 5·1.5/6 = 1.25 kN
Leg BC: moments about C
1.25·3 = T·2.4
T = 1.562 kN
Answer
T = 1.562 kN
8.Frames & machines
Answer: A = 22.01 kN
Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.
Cable tension
T = (5 + 1/2)/0.2425 = 22.68 kN
Components at A
Ax = T·cos β = 22 kN
Ay = 5 + 1 − T·sin β = 0.5 kN
Magnitude
A = √(22² + 0.5²) = 22.01 kN
Answer
A = 22.01 kN
9.Shear force & bending moment
Answer: D (x = 3 m)
Largest bending moment: M changes slope wherever the shear force changes, so its peaks sit where the shear force crosses zero: under a point load, inside a distributed load, or over a support of an overhang. At a fixed support of a cantilever the moment is largest at the wall. Compare the size of M at those places, sagging or hogging.
Support reactions
Take moments about one support, then use the vertical force balance.
R1 = 43 kN, R2 = 43 kN
Bending moment at every mark
Sum the moments of all forces on one side of the cut. Sagging is positive, hogging negative.
MA = 0, MB = 40, MC = 74, MD = 102 kN·m, ME = 74, MF = 40, MG = 0
Answer
Mark D: MD = 102 kN·m
10.Shear force & bending moment
Answer: Mmax = 22.34 kN·m
Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut. Maximum moment: since dM/dx = V, the bending moment has its peak where the shear force passes through zero, either at a point load or inside a distributed load.
Support reactions
Equilibrium of the whole beam, including the load on the overhang.
UDL resultant: W = w·ℓ = 3·9.5 = 28.5 kN, acting at x̄ = 4.75 m
Sections with holes: treat a hole as a negative area. The centroid is ȳ = (A₁y₁ − A₂y₂)/(A₁ − A₂), with A₁, y₁ for the full plate and A₂, y₂ for the hole. For the second moment of area about the centroidal axis, use the parallel-axis theorem for each part and subtract the hole: I = (Ic1 + A₁d₁²) − (Ic2 + A₂d₂²), where d is the distance from each part's own centroid to the axis through ȳ. A rectangle has Ic = bh³/12 and a circle Ic = πd⁴/64.
Centroid
ȳ = (48000·120 − 706.9·84)/(48000 − 706.9) = 120.5 mm
Full plate about ȳ
200·240³/12 + 48000·−0.5381² = 230.4 × 10⁶ mm⁴
Hole about ȳ
π·30⁴/64 + 706.9·−36.54² = 0.9834 × 10⁶ mm⁴
Subtract
Ix = 229.4 × 10⁶ mm⁴
Answer
Ix = 229.4 × 10⁶ mm⁴
12.Centroid & second moment of area
Answer: Ix = 27.19 × 10⁶ mm⁴
Sections with holes: treat a hole as a negative area. The centroid is ȳ = (A₁y₁ − A₂y₂)/(A₁ − A₂), with A₁, y₁ for the full plate and A₂, y₂ for the hole. For the second moment of area about the centroidal axis, use the parallel-axis theorem for each part and subtract the hole: I = (Ic1 + A₁d₁²) − (Ic2 + A₂d₂²), where d is the distance from each part's own centroid to the axis through ȳ. A rectangle has Ic = bh³/12 and a circle Ic = πd⁴/64.
Centroid
ȳ = (15000·75 − 2000·60)/(15000 − 2000) = 77.31 mm