Statics: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Vectors: dot & cross product

Magnitude
|a| = √(ax² + ay² + az²)
Unit vector
û = a/|a|
Components from an angle
Fx = F·cos θ, Fy = F·sin θ
Dot product
a·b = axbx + ayby + azbz = |a||b|cos θ
Scalar projection of a onto b
a·b/|b|
Work
W = F·d
Cross product
a × b = (aybz − azby, azbx − axbz, axby − aybx)
Areas
parallelogram |a × b|, triangle ½|a × b|
Moment about O
MO = r × F, r = A − O
Volume of a parallelepiped
V = |a·(b × c)|

Method

  1. Write every vector in components; for a force given by a magnitude and an angle, use F·cos θ and F·sin θ.
  2. For lengths and directions use the magnitude √(x² + y² + z²) and the unit vector a/|a|.
  3. Use the dot product for angles, projections, perpendicularity and work: a·b = |a||b|cos θ.
  4. Use the cross product for perpendicular vectors, areas and moments: write the three components carefully, keeping the order a × b.

Beam support reactions

Equilibrium
ΣFx = 0, ΣFy = 0, ΣM = 0
Uniform load
resultant w·L at the middle of the load
Moment
M = F·d

Method

  1. Draw a free-body diagram and replace each support by its reactions.
  2. Replace every distributed load by a single force at its centroid.
  3. Take moments about one support to find the reaction at the other.
  4. Use ΣFy = 0 to find the remaining reaction, and check with a second moment equation.

Truss: method of joints

Method of joints
ΣFx = 0, ΣFy = 0 at each joint
Method of sections
ΣM = 0 about a cut point
Member force
positive = tension, negative = compression

Method

  1. Find the support reactions for the whole truss.
  2. Method of joints: start at a joint with at most two unknown member forces and use ΣFx = 0 and ΣFy = 0.
  3. Method of sections: cut through the member you need and take moments about a point where the other unknown members meet.
  4. Assume tension; a negative answer means compression.

Frames & machines

Equilibrium of each member
ΣFx = 0, ΣFy = 0, ΣM = 0
Two-force member
force along the line through its two pins
Pin force
equal and opposite on the two members it joins
Magnitude of a pin force
F = √(Fx² + Fy²)
Lever, pliers, bell crank
Fin·a = Fout·b
Toggle
Flink = F/(2 sin θ), Q = F/(2 tan θ)
Uniform load
resultant w·L at the middle of the load

Method

  1. Draw the whole structure and find the support reactions if there are no more than three unknowns.
  2. Spot the two-force members: loaded only at two pins, their force acts along the line between the pins.
  3. Take the frame apart and draw every member on its own, with equal and opposite pin forces where members meet.
  4. For each member, take moments about a pin with unknown forces, then use ΣFx = 0 and ΣFy = 0; combine components into a magnitude at the end.

Shear force & bending moment

Shear and moment
V = ΣF on one side, M = ΣF·d on one side
Bending stress
σ = M·y/I
Rectangle
I = bh³/12
Section modulus
W = I/ymax
Simply supported, uniform load
Mmax = wL²/8

Method

  1. Find the support reactions from equilibrium of the whole beam.
  2. Cut the beam at the section you need and keep one side.
  3. Shear force: sum of the vertical forces on that side. Bending moment: sum of their moments about the cut.
  4. For the maximum moment, find where the shear force is zero.

Centroid & second moment of area

Centroid
ȳ = ΣAiyi/ΣAi
Rectangle
I = bh³/12
Parallel-axis theorem
I = Ic + A·d²
Composite section
I = Σ(Ic,i + Aidi²)

2Practice problems

1.Vectors: dot & cross productMedium
xyzab

Find the dot product a·b of a = (−5, 5, −1) and b = (6, 3, −4).

a = (−5, 5, −1)b = (6, 3, −4)
a·b =
2.Vectors: dot & cross productHard
xyzab

For a = (0, −6, 6) and b = (−4, 2, −5), find the y-component (a × b)y of the cross product a × b.

a = (0, −6, 6)b = (−4, 2, −5)
(a × b)y =
3.Beam support reactionsMedium
P = 40 kNM = 10 kN·mABRB​ = ?1 m2 m7 m

The simply supported beam has a pin at A and a roller at B. It carries a point load P at 3 m from A and a counter-clockwise couple M at 1 m from A. Find the vertical reaction RB, taking upward as positive.

L = 10 mP = 40 kN at 3 mM = 10 kN·m (counter-clockwise) at 1 m
RB = kN
4.Beam support reactionsHard
w = 12 kN/mP = 55 kNABRA​RB​ = ?1.5 m1.5 m1 m

The simply supported beam has a pin at A and a roller at B. Find the vertical support reaction RB.

L = 4 mP = 55 kN at 1.5 mw = 12 kN/m from 0 to 3 m
RB = kN
5.Truss: method of jointsMedium
ABCDEFGH25 kN15 kN25 kN4 × 3 m3 m

Exactly one member of this truss carries no force under these loads. Which is the zero-force member? Click it in the diagram.

B: 25 kN ↓F: 15 kN ↓H: 25 kN ↓
  1. 1member AB
  2. 2member BC
  3. 3member CD
  4. 4member DE
  5. 5member FG
  6. 6member GH
  7. 7member AF
  8. 8member HE
  9. 9member BF
  10. 10member CG
  11. 11member DH
  12. 12member BG
  13. 13member DG
6.Truss: method of jointsHard
ABBCACACB20 kN10 kN4 m1 m4 m

Use the method of joints to find the force FBC in member BC. Give tension as positive and compression as negative.

span = 4 mheight = 4 mB is 1 m from Avertical load = 20 kNhorizontal load = 10 kN →
FBC = kN
7.Frames & machinesMedium
20 kN3 m0.8 m3.2 m0.75 mABCDEK

The A-frame shown stands on a pin at A and a roller at B, 3 m apart, with its apex pin C 4 m high and the horizontal tie DE 0.8 m above the ground. A vertical load of 20 kN acts on leg AC at K, 0.75 m (horizontally) from A. Find the tension T in the tie.

P = 20 kNAB = 3 mheight of C = 4 mheight of DE = 0.8 mhorizontal distance A to K = 0.75 m
T = kN
8.Frames & machinesHard
w = 3 kN/m12 kN1.6 m0.9 m1.2 mABCD

The beam AB of the wall bracket shown is pinned at A and propped by the strut CD (C is 1.2 m below A). The beam carries a uniform load of 3 kN/m over its full length and a point load of 12 kN at its free end B. Find the force FCD in the strut.

w = 3 kN/mP = 12 kNAD = 1.6 mAB = 2.5 mAC = 1.2 m
FCD = kN
9.Shear force & bending momentMedium
P1​ = 60 kNP2​ = 80 kNAB6 m2 m2 m

The simply supported beam carries two point loads. Find the maximum bending moment Mmax in the beam.

L = 10 mP1 = 60 kN at 6 mP2 = 80 kN at 8 m
Mmax = kN·m
10.Shear force & bending momentHard
w = 12 kN/mP = 25 kNAB2 m8 m

The simply supported beam carries a uniformly distributed load w over its whole span and a point load P. Find the maximum bending moment Mmax in the beam.

L = 10 mP = 25 kN at 2 mw = 12 kN/m from 0 to 10 m
Mmax = kN·m
11.Centroid & second moment of areaMedium
18080t = 18xdimensions in mm

A channel section lies with its open side up: a base plate 180 mm wide with two upright legs, 80 mm high overall. Base and legs are all 18 mm thick. Find its second moment of area Ix about the horizontal axis x through its centroid.

b = 180 mmh = 80 mmt = 18 mm
Ix = × 10⁶ mm⁴
12.Centroid & second moment of areaHard
2503801614xM = 50 kN·mdimensions in mm

A symmetric I-section has flanges 250 mm wide and 16 mm thick, an overall depth of 380 mm and a web 14 mm thick. It carries a bending moment of 50 kN·m about the axis x. Find the size of the bending stress σj at the junction of the web and the top flange.

B = 250 mmH = 380 mmtf = 16 mmtw = 14 mmM = 50 kN·m
σj = MPa

3Solutions

1.Vectors: dot & cross product

Answer: a·b = −11

Dot product: a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.

Multiply matching components and add

a·b = (−5)·6 + 5·3 + (−1)·(−4) = (−30) + 15 + 4 = −11

Answer

a·b = −11

Negative: the angle between the vectors is more than 90°.

2.Vectors: dot & cross product

Answer: (a × b)y = −24

Cross product: a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.

Cross product, component by component

(a × b)x = aybz − azby = (−6)·(−5) − 6·2 = 18
(a × b)y = azbx − axbz = 6·(−4) − 0·(−5) = −24
(a × b)z = axby − aybx = 0·2 − (−6)·(−4) = −24

Requested component

(a × b)y = −24

Answer

(a × b)y = −24

Check: a × b is perpendicular to both vectors, so its dot product with a and with b is zero.

3.Beam support reactions

Answer: RB = 11 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Replace each distributed load by its resultant (its area) acting at the centroid of the load diagram, and take moments about a support to remove that support’s reaction from the equation.

Moments about A

Counter-clockwise positive.

ΣMA = 0: RB·10 − 40·3 + 10 = 0
RB = 110/10 = 11 kN

Vertical equilibrium

RA = 40 − 11 = 29 kN

Answer

RB = 11 kN

A negative reaction acts downward.

4.Beam support reactions

Answer: RB = 34.13 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.

w = 12 kN/mP = 55 kNABRA​RB​1.5 m1.5 m1 m

Free-body diagram

Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.

Equilibrium

Moments about A, counter-clockwise positive. Then vertical force balance.

UDL resultant: W = w·ℓ = 12·3 = 36 kN, acting at x̄ = 1.5 m
ΣMA = 0: RB·4 = 55·1.5 + 12·3·1.5
RB = 136.5/4 = 34.13 kN
ΣFy = 0: RA = 91 − 34.13 = 56.88 kN

Answer

RB = 34.13 kN
5.Truss: method of joints

Answer: member CG

Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.

Joint C

BC and CD lie on one straight line and the joint carries no load. Balancing forces across that line leaves only CG.

ΣF⊥ = 0 → FCG = 0

Check with the method of joints

Solving all joints gives these member forces (T = tension, C = compression).

AB: 36.25 kN (T), BC: 32.5 kN (T), CD: 32.5 kN (T), DE: 28.75 kN (T), FG: 36.25 kN (C), GH: 28.75 kN (C), AF: 51.27 kN (C), HE: 40.66 kN (C), BF: 21.25 kN (T), CG: 0, DH: 3.75 kN (T), BG: 5.303 kN (T), DG: 5.303 kN (C)

Answer

Zero-force member: CG
6.Truss: method of joints

Answer: FBC = −18.75 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB20 kN10 kNAy​Cy​Ax​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·4 = 20·1 + 10·4 → Cy = 15 kN
ΣFy = 0: Ay = 20 − 15 = 5 kN
ΣFx = 0: Ax = −10 kN

Joint C

The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.

sin γ = 4/5 = 0.8, cos γ = 3/5 = 0.6
ΣFy = 0: Cy + FBC·sin γ = 0 → FBC = −15/0.8 = −18.75 kN

Answer

FBC = −18.75 kN (compression)
7.Frames & machines

Answer: T = 2.344 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Whole frame: moments about A

By = 20·0.75/3 = 5 kN

Leg BC: moments about C

5·1.5 = T·3.2
T = 2.344 kN

Answer

T = 2.344 kN
8.Frames & machines

Answer: FCD = 41.02 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Resultant of the uniform load

w·L = 3·2.5 = 7.5 kN at 1.25 m

Moments about A for the beam

FCD·0.6·1.6 = 7.5·1.25 + 12·2.5 = 39.38 kN·m
FCD = 41.02 kN

Answer

FCD = 41.02 kN
9.Shear force & bending moment

Answer: Mmax = 240 kN·m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut. Maximum moment: since dM/dx = V, the bending moment has its peak where the shear force passes through zero, either at a point load or inside a distributed load.

Support reactions

Equilibrium of the whole beam.

ΣMA = 0: RB·10 = 60·6 + 80·8
RB = 1000/10 = 100 kN
ΣFy = 0: RA = 140 − 100 = 40 kN

Moment under each load

Keep the part left of each load.

under P1: M = RA·6 = 40·6 = 240 kN·m
under P2: M = RB·2 = 100·2 = 200 kN·m

Largest value

Mmax = 240 kN·m (under P1)

Answer

Mmax = 240 kN·m
10.Shear force & bending moment

Answer: Mmax = 176 kN·m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut. Maximum moment: since dM/dx = V, the bending moment has its peak where the shear force passes through zero, either at a point load or inside a distributed load.

Support reactions

Equilibrium of the whole beam.

UDL resultant: W = w·ℓ = 12·10 = 120 kN, acting at x̄ = 5 m
ΣMA = 0: RB·10 = 25·2 + 12·10·5
RB = 650/10 = 65 kN
ΣFy = 0: RA = 145 − 65 = 80 kN

Where is V = 0?

RA − P − w·x0 = 0 → x0 = (80 − 25)/12 = 4.583 m

Maximum moment

Mmax = RA·x0 − P·(x0 − 2) − w·x0²/2 = 176 kN·m

Answer

Mmax = 176 kN·m

It occurs at x = 4.583 m from A.

11.Centroid & second moment of area

Answer: Ix = 2.917 × 10⁶ mm⁴

Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.

Split into rectangles

Take the base at full width and the two legs above it (height h − t), so nothing is counted twice.

base: A1 = 180·18 = 3240 mm², y1 = 9 mm
two legs: A2 = 2·18·62 = 2232 mm², y2 = 18 + 62/2 = 49 mm

Centroid

ȳ = (3240·9 + 2232·49)/5472 = 25.32 mm

Parallel-axis theorem

base: 180·18³/12 + 3240·(9 − 25.32)² = 949984 mm⁴
two legs: 2·18·62³/12 + 2232·(49 − 25.32)² = 1.967 × 10⁶ mm⁴
Ix = 949984 + 1.967 × 10⁶
Ix = 2.917 × 10⁶ mm⁴ = 2.917 × 10⁶ mm⁴

Answer

Ix = 2.917 × 10⁶ mm⁴
12.Centroid & second moment of area

Answer: σj = 27.68 MPa

Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.

Outer rectangle minus the two side cut-outs

Both cut-outs together are (B − tw) wide and hw = H − 2tf high, and share the axis x.

hw = 380 − 2·16 = 348 mm
Ix = (B·H³ − (B − tw)·hw³)/12 = (250·380³ − 236·348³)/12
Ix = 3.143 × 10⁸ mm⁴

Bending stress

y = 190 − 16 = 174 mm
σ = M·y/I = 5 × 10⁷·174/3.143 × 10⁸ = 27.68 MPa

Answer

σj = 27.68 MPa

ExamProblems · examproblems.com/courses/statics