The A-frame shown stands on a pin at A and a roller at B, 3.2 m apart, with its apex pin C 3.6 m high and the horizontal tie DE 1.2 m above the ground. A vertical load of 5 kN acts on leg AC at K, 0.8 m (horizontally) from A. Find the tension T in the tie.
P = 5 kNAB = 3.2 mheight of C = 3.6 mheight of DE = 1.2 mhorizontal distance A to K = 0.8 m
T = kN
8.Frames & machinesHard
A toggle press has two equal links AB and BC, each 80 mm long between pins. The joint B sits 20 mm above the line AC. Which downward force F at B produces a horizontal pressing force of 5000 N at the slider C? Neglect friction and weights.
Q = 5000 NAB = BC = 80 mmh = 20 mm
F = N
9.Shear force & bending momentMedium
The cantilever is fixed at A. It carries a uniformly distributed load w over its whole length and a point load P at 2.5 m from A. Find the bending moment MA at the fixed support A. Use sagging moments positive and upward shear on the left face positive.
L = 3 mP = 25 kN at 2.5 mw = 2 kN/m from 0 to 3 m
MA = kN·m
10.Shear force & bending momentHard
Find the bending moment Mx at the section x = 2 m from support A. Use sagging moments positive and upward shear on the left face positive.
L = 6 mP = 40 kN at 5 mw = 4 kN/m from 0 to 6 mx = 2 m
Mx = kN·m
11.Centroid & second moment of areaMedium
A symmetric I-section has flanges 130 mm wide and 10 mm thick, an overall depth of 440 mm and a web 8 mm thick. Find its second moment of area Ix about the horizontal centroidal axis x.
B = 130 mmH = 440 mmtf = 10 mmtw = 8 mm
Ix = × 10⁶ mm⁴
12.Centroid & second moment of areaHard
A 100 mm × 240 mm plate has a rectangular cut-out 50 mm wide and 40 mm high, centred on the vertical centre line with its centre 156 mm above the bottom. Find the second moment of area Ix about the horizontal axis through the centroid.
b = 100 mmh = 240 mmcut-out: 50 × 40 mmhole centre: y = 156 mm
Ix = × 10⁶ mm⁴
3Solutions
1.Vectors: dot & cross product
Answer: k = −3.4
Dot product:a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.
Dot product equals zero
a·b = (−6)·(−3) + 5·k + (−1)·1 = 0
17 + 5·k = 0
Solve for k
k = −17/5 = −3.4
Answer
k = −3.4
2.Vectors: dot & cross product
Answer: (a × b)z = −1
Cross product:a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.
Cross product, component by component
(a × b)x = aybz − azby = 2·0 − 3·1 = −3
(a × b)y = azbx − axbz = 3·2 − 3·0 = 6
(a × b)z = axby − aybx = 3·1 − 2·2 = −1
Requested component
(a × b)z = −1
Answer
(a × b)z = −1
Check: a × b is perpendicular to both vectors, so its dot product with a and with b is zero.
3.Beam support reactions
Answer: RA = 2.143 kN
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Replace each distributed load by its resultant (its area) acting at the centroid of the load diagram, and take moments about a support to remove that support’s reaction from the equation.
Moments about A
Counter-clockwise positive.
ΣMA = 0: RB·3.5 = 15·0.5 + 25·5
RB = 132.5/3.5 = 37.86 kN
Vertical equilibrium
RA = 15 + 25 − 37.86 = 2.143 kN
Answer
RA = 2.143 kN
4.Beam support reactions
Answer: RA = 7.2 kN
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.
Free-body diagram
Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.
Equilibrium
Moments about A, counter-clockwise positive. Then vertical force balance.
UDL resultant: W = w·ℓ = 8·2 = 16 kN, acting at x̄ = 4 m
ΣMA = 0: RB·5 = 10·3 + 8·2·4
RB = 94/5 = 18.8 kN
ΣFy = 0: RA = 26 − 18.8 = 7.2 kN
Answer
RA = 7.2 kN
5.Truss: method of joints
Answer: FBC = −11.18 kN
Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.
Support reactions
Equilibrium of the whole truss. Moments about A, counter-clockwise positive.
ΣMA = 0: Cy·5 = 25·1 → Cy = 5 kN
ΣFy = 0: Ay = 25 − 5 = 20 kN
Joint C
The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.
sin γ = 2/4.472 = 0.4472, cos γ = 4/4.472 = 0.8944
Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.
Joint G
FG and GH lie on one straight line and the joint carries no load. Balancing forces across that line leaves only CG.
ΣF⊥ = 0 → FCG = 0
Check with the method of joints
Solving all joints gives these member forces (T = tension, C = compression).
Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.
Whole frame: moments about A
By = 5·0.8/3.2 = 1.25 kN
Leg BC: moments about C
1.25·1.6 = T·2.4
T = 0.8333 kN
Answer
T = 0.8333 kN
8.Frames & machines
Answer: F = 2582 N
Machines: pliers, levers, linkages and clamps turn an input force into a larger or a differently directed output force. Draw one part as a free body and take moments about its pivot: the pin force drops out, and Fin·a = Fout·b gives the mechanical advantage a/b. The pin force then follows from ΣF = 0 on the same part. In a toggle, two links meet at a shallow angle θ; each link is a two-force member, so a small force F at the joint creates large link forces F/(2 sin θ) and a clamping force F/(2 tan θ).
Link angle
sin θ = 20/80 = 0.25, θ = 14.48°
Link force
Flink = Q/cos θ = 5164 N
Force at B
F = 2·Flink·sin θ = 2·5000·tan θ = 2582 N
Answer
F = 2582 N
9.Shear force & bending moment
Answer: MA = −71.5 kN·m
Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.
Keep the free-end part
P: −25·2.5 = −62.5 kN·m
w: −2·3²/2 = −9 kN·m
MA = −62.5 − 9 = −71.5 kN·m
Answer
MA = −71.5 kN·m
Negative means hogging: tension on the top face.
10.Shear force & bending moment
Answer: Mx = 29.33 kN·m
Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.
Support reactions
Equilibrium of the whole beam.
UDL resultant: W = w·ℓ = 4·6 = 24 kN, acting at x̄ = 3 m
ΣMA = 0: RB·6 = 40·5 + 4·6·3
RB = 272/6 = 45.33 kN
ΣFy = 0: RA = 64 − 45.33 = 18.67 kN
Cut at x = 2 m and keep the left part
Only forces left of the cut appear. A UDL portion acts as one force at the middle of that portion.
M = RA·x − (each load left of the cut × its distance to the cut)
Mx = 18.67·2 − 4·2·1 = 29.33 kN·m
Answer
Mx = 29.33 kN·m
11.Centroid & second moment of area
Answer: Ix = 169.6 × 10⁶ mm⁴
Second moment of area: for a rectangle about its own centroidal axis I = bh³/12, and about its base bh³/3 (parallel-axis theorem I = Ic + A·d²). A hole is handled by subtracting its I, as long as both parts share the same axis. The elastic section modulus is S = I/c, where c is the distance to the extreme fibre.
Outer rectangle minus the two side cut-outs
Both cut-outs together are (B − tw) wide and hw = H − 2tf high, and share the axis x.
Sections with holes: treat a hole as a negative area. The centroid is ȳ = (A₁y₁ − A₂y₂)/(A₁ − A₂), with A₁, y₁ for the full plate and A₂, y₂ for the hole. For the second moment of area about the centroidal axis, use the parallel-axis theorem for each part and subtract the hole: I = (Ic1 + A₁d₁²) − (Ic2 + A₂d₂²), where d is the distance from each part's own centroid to the axis through ȳ. A rectangle has Ic = bh³/12 and a circle Ic = πd⁴/64.
Centroid
ȳ = (24000·120 − 2000·156)/(24000 − 2000) = 116.7 mm