The A-frame shown stands on a pin at A and a roller at B, 3.2 m apart, with its apex pin C 2.4 m high and the horizontal tie DE 1 m above the ground. A vertical load of 15 kN acts on leg AC at K, 0.96 m (horizontally) from A. Find the tension T in the tie.
P = 15 kNAB = 3.2 mheight of C = 2.4 mheight of DE = 1 mhorizontal distance A to K = 0.96 m
T = kN
8.Frames & machinesHard
The A-frame shown stands on a pin at A and a roller at B, 3 m apart. The legs meet at the pin C, 2.5 m high, and are tied by the horizontal bar DE at 0.8 m. A horizontal force of 15 kN to the right acts at C. Find the tension T in the tie.
P = 15 kNAB = 3 mheight of C = 2.5 mheight of DE = 0.8 m
T = kN
9.Shear force & bending momentMedium
The simply supported beam carries two point loads. Find the maximum bending moment Mmax in the beam.
L = 8 mP1 = 15 kN at 3 mP2 = 55 kN at 7 m
Mmax = kN·m
10.Shear force & bending momentHard
The simply supported beam carries a uniformly distributed load w over its whole span and a point load P. Find the maximum bending moment Mmax in the beam.
L = 10 mP = 10 kN at 9 mw = 6 kN/m from 0 to 10 m
Mmax = kN·m
11.Centroid & second moment of areaMedium
A 150 mm × 240 mm plate has a circular hole of diameter 60 mm on its vertical centre line, with its centre 144 mm above the bottom. Find the second moment of area Ix about the horizontal axis through the centroid.
b = 150 mmh = 240 mmd = 60 mmhole centre: y = 144 mm
Ix = × 10⁶ mm⁴
12.Centroid & second moment of areaHard
A welded I-section has a top flange 180 × 16 mm, a web 330 mm high and 10 mm thick, and a bottom flange 220 × 16 mm (width × thickness). Find its second moment of area Ix about the horizontal axis x through its centroid.
top flange: 180 × 16 mmweb: 10 × 330 mmbottom flange: 220 × 16 mm
Ix = × 10⁶ mm⁴
3Solutions
1.Vectors: dot & cross product
Answer: compb a = 4.899
Dot product:a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.
Dot product
a·b = (−2)·(−6) + (−5)·(−3) + 3·3 = 36
Length of b
|b| = √((−6)² + (−3)² + 3²) = 7.348
Scalar projection
compb a = a·b/|b| = 36/7.348 = 4.899
Answer
compb a = 4.899
2.Vectors: dot & cross product
Answer: A = 13.75 m²
Cross product:a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.
Free-body diagram
Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.
Equilibrium
Moments about A, counter-clockwise positive. Then vertical force balance.
ΣMA = 0: RB·6 = 20·2 + 40·3.5
RB = 180/6 = 30 kN
ΣFy = 0: RA = 60 − 30 = 30 kN
Answer
RA = 30 kN
4.Beam support reactions
Answer: RB = 7.55 kN
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.
Free-body diagram
Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.
Equilibrium
Moments about A, counter-clockwise positive. Then vertical force balance.
UDL resultant: W = w·ℓ = 3·1 = 3 kN, acting at x̄ = 8.5 m
ΣMA = 0: RB·10 = 25·2 + 3·1·8.5
RB = 75.5/10 = 7.55 kN
ΣFy = 0: RA = 28 − 7.55 = 20.45 kN
Answer
RB = 7.55 kN
5.Truss: method of joints
Answer: member CG
Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.
Joint G
FG and GH lie on one straight line and the joint carries no load. Balancing forces across that line leaves only CG.
ΣF⊥ = 0 → FCG = 0
Check with the method of joints
Solving all joints gives these member forces (T = tension, C = compression).
Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.
Joint B
AB and BC lie on one straight line and the joint carries no load. Balancing forces across that line leaves only BF.
ΣF⊥ = 0 → FBF = 0
Check with the method of joints
Solving all joints gives these member forces (T = tension, C = compression).
Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.
Whole frame: moments about A
By = 15·0.96/3.2 = 4.5 kN
Leg BC: moments about C
4.5·1.6 = T·1.4
T = 5.143 kN
Answer
T = 5.143 kN
8.Frames & machines
Answer: T = 11.03 kN
Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.
Whole frame: moments about A
By·3 = 15·2.5
By = 12.5 kN
Leg BC: moments about C
12.5·1.5 = T·1.7
T = 11.03 kN
Answer
T = 11.03 kN
A positive T means the tie is in tension, as assumed.
9.Shear force & bending moment
Answer: Mmax = 53.75 kN·m
Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut. Maximum moment: since dM/dx = V, the bending moment has its peak where the shear force passes through zero, either at a point load or inside a distributed load.
Support reactions
Equilibrium of the whole beam.
ΣMA = 0: RB·8 = 15·3 + 55·7
RB = 430/8 = 53.75 kN
ΣFy = 0: RA = 70 − 53.75 = 16.25 kN
Moment under each load
Keep the part left of each load.
under P1: M = RA·3 = 16.25·3 = 48.75 kN·m
under P2: M = RB·1 = 53.75·1 = 53.75 kN·m
Largest value
Mmax = 53.75 kN·m (under P2)
Answer
Mmax = 53.75 kN·m
10.Shear force & bending moment
Answer: Mmax = 80.08 kN·m
Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut. Maximum moment: since dM/dx = V, the bending moment has its peak where the shear force passes through zero, either at a point load or inside a distributed load.
Support reactions
Equilibrium of the whole beam.
UDL resultant: W = w·ℓ = 6·10 = 60 kN, acting at x̄ = 5 m
Sections with holes: treat a hole as a negative area. The centroid is ȳ = (A₁y₁ − A₂y₂)/(A₁ − A₂), with A₁, y₁ for the full plate and A₂, y₂ for the hole. For the second moment of area about the centroidal axis, use the parallel-axis theorem for each part and subtract the hole: I = (Ic1 + A₁d₁²) − (Ic2 + A₂d₂²), where d is the distance from each part's own centroid to the axis through ȳ. A rectangle has Ic = bh³/12 and a circle Ic = πd⁴/64.
Centroid
ȳ = (36000·120 − 2827·144)/(36000 − 2827) = 118 mm
Full plate about ȳ
150·240³/12 + 36000·2.046² = 173 × 10⁶ mm⁴
Hole about ȳ
π·60⁴/64 + 2827·26.05² = 2.554 × 10⁶ mm⁴
Subtract
Ix = 170.4 × 10⁶ mm⁴
Answer
Ix = 170.4 × 10⁶ mm⁴
12.Centroid & second moment of area
Answer: Ix = 220.4 × 10⁶ mm⁴
Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.
Split into three rectangles
Measure every y from the bottom edge.
top flange: A = 2880 mm², y = 354 mm
web: A = 3300 mm², y = 181 mm
bottom flange: A = 3520 mm², y = 8 mm
Centroid
ȳ = (2880·354 + 3300·181 + 3520·8)/9700 = 169.6 mm
Parallel-axis theorem
top flange: 180·16³/12 + 2880·184.4² = 9.801 × 10⁷ mm⁴