Statics: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Vectors: dot & cross product

Magnitude
|a| = √(ax² + ay² + az²)
Unit vector
û = a/|a|
Components from an angle
Fx = F·cos θ, Fy = F·sin θ
Dot product
a·b = axbx + ayby + azbz = |a||b|cos θ
Scalar projection of a onto b
a·b/|b|
Work
W = F·d
Cross product
a × b = (aybz − azby, azbx − axbz, axby − aybx)
Areas
parallelogram |a × b|, triangle ½|a × b|
Moment about O
MO = r × F, r = A − O
Volume of a parallelepiped
V = |a·(b × c)|

Method

  1. Write every vector in components; for a force given by a magnitude and an angle, use F·cos θ and F·sin θ.
  2. For lengths and directions use the magnitude √(x² + y² + z²) and the unit vector a/|a|.
  3. Use the dot product for angles, projections, perpendicularity and work: a·b = |a||b|cos θ.
  4. Use the cross product for perpendicular vectors, areas and moments: write the three components carefully, keeping the order a × b.

Beam support reactions

Equilibrium
ΣFx = 0, ΣFy = 0, ΣM = 0
Uniform load
resultant w·L at the middle of the load
Moment
M = F·d

Method

  1. Draw a free-body diagram and replace each support by its reactions.
  2. Replace every distributed load by a single force at its centroid.
  3. Take moments about one support to find the reaction at the other.
  4. Use ΣFy = 0 to find the remaining reaction, and check with a second moment equation.

Truss: method of joints

Method of joints
ΣFx = 0, ΣFy = 0 at each joint
Method of sections
ΣM = 0 about a cut point
Member force
positive = tension, negative = compression

Method

  1. Find the support reactions for the whole truss.
  2. Method of joints: start at a joint with at most two unknown member forces and use ΣFx = 0 and ΣFy = 0.
  3. Method of sections: cut through the member you need and take moments about a point where the other unknown members meet.
  4. Assume tension; a negative answer means compression.

Frames & machines

Equilibrium of each member
ΣFx = 0, ΣFy = 0, ΣM = 0
Two-force member
force along the line through its two pins
Pin force
equal and opposite on the two members it joins
Magnitude of a pin force
F = √(Fx² + Fy²)
Lever, pliers, bell crank
Fin·a = Fout·b
Toggle
Flink = F/(2 sin θ), Q = F/(2 tan θ)
Uniform load
resultant w·L at the middle of the load

Method

  1. Draw the whole structure and find the support reactions if there are no more than three unknowns.
  2. Spot the two-force members: loaded only at two pins, their force acts along the line between the pins.
  3. Take the frame apart and draw every member on its own, with equal and opposite pin forces where members meet.
  4. For each member, take moments about a pin with unknown forces, then use ΣFx = 0 and ΣFy = 0; combine components into a magnitude at the end.

Shear force & bending moment

Shear and moment
V = ΣF on one side, M = ΣF·d on one side
Bending stress
σ = M·y/I
Rectangle
I = bh³/12
Section modulus
W = I/ymax
Simply supported, uniform load
Mmax = wL²/8

Method

  1. Find the support reactions from equilibrium of the whole beam.
  2. Cut the beam at the section you need and keep one side.
  3. Shear force: sum of the vertical forces on that side. Bending moment: sum of their moments about the cut.
  4. For the maximum moment, find where the shear force is zero.

Centroid & second moment of area

Centroid
ȳ = ΣAiyi/ΣAi
Rectangle
I = bh³/12
Parallel-axis theorem
I = Ic + A·d²
Composite section
I = Σ(Ic,i + Aidi²)

2Practice problems

1.Vectors: dot & cross productMedium
xyzab

Find the dot product a·b of a = (2, 5, −4) and b = (−4, 4, 7).

a = (2, 5, −4)b = (−4, 4, 7)
a·b =
2.Vectors: dot & cross productHard
xyzrFOA

A force F = (50, −20, 0) N acts at point A(0, −1, −1). Coordinates are in metres. Find the z-component Mz of the moment of the force about point O(3, −1, 2).

F = (50, −20, 0) NA(0, −1, −1) mO(3, −1, 2) m
Mz = N·m
3.Beam support reactionsMedium
P1​ = 10 kNP2​ = 65 kNABCRA​ = ?1 m2 m1 m

The beam has a pin at A and a roller at B, 3 m from A, and overhangs B to the free end C. Find the vertical reaction RA, taking upward as positive.

AB = 3 mAC = 4 mP1 = 10 kN at 1 mP2 = 65 kN at 4 m
RA = kN
4.Beam support reactionsHard
w = 2 kN/mP = 35 kNABRA​RB​ = ?3 m3 m1 m1 m

The simply supported beam has a pin at A and a roller at B. Find the vertical support reaction RB.

L = 8 mP = 35 kN at 3 mw = 2 kN/m from 6 to 7 m
RB = kN
5.Truss: method of jointsMedium
ABBCACACB45 kN8 m2 m3 m

Use the method of joints to find the force FBC in member BC. Give tension as positive and compression as negative.

span = 8 mheight = 3 mB is 2 m from Avertical load = 45 kN
FBC = kN
6.Truss: method of jointsHard
ABCDEFGH15 kN20 kN40 kN25 kN4 × 3 m3 m

Exactly one member of this truss carries no force under these loads. Which is the zero-force member? Click it in the diagram.

B: 15 kN ↓D: 20 kN ↓H: 40 kN ↓H: 25 kN ←
  1. 1member AB
  2. 2member BC
  3. 3member CD
  4. 4member DE
  5. 5member FG
  6. 6member GH
  7. 7member AF
  8. 8member HE
  9. 9member BF
  10. 10member CG
  11. 11member DH
  12. 12member BG
  13. 13member DG
7.Frames & machinesMedium
20 kN5 m1.8 m2.2 mABCDE

The A-frame shown stands on a pin at A and a roller at B, 5 m apart. The legs meet at the pin C, 4 m high, and the horizontal tie DE is 1.8 m above the ground. A load of 20 kN acts at C. Find the magnitude of the force C that the pin C exerts on leg BC.

P = 20 kNAB = 5 mheight of C = 4 mheight of DE = 1.8 m
C = kN
8.Frames & machinesHard
6 kN10 kN5 m2 m3 mABCK

The frame shown has pins at A, B and C; A and C are fixed to the ground 5 m apart, and B is 2 m high and 3 m to the right of A. Member AB carries a vertical load of 6 kN at K, 1.8 m (horizontally) from A, and a horizontal load of 10 kN to the right acts at B on member AB. Find the size of the horizontal reaction Ax at A.

P = 6 kNQ = 10 kNL = 5 mH = 2 mhorizontal distance A to B = 3 mhorizontal distance A to K = 1.8 m
Ax = kN
9.Shear force & bending momentMedium
M0​ = 50 kN·mAB5 m1 m

The simply supported beam carries a clockwise couple M0 = 50 kN·m at x = 5 m from A, and no other load. Find the bending moment Mx just to the left of the couple. Use sagging moments positive and upward shear on the left face positive.

L = 6 mM0 = 50 kN·m clockwise, at 5 m
Mx = kN·m
10.Shear force & bending momentHard
w = 10 kN/mP = 40 kNABsection7 m1 m

Find the bending moment Mx at the section x = 7 m from support A. Use sagging moments positive and upward shear on the left face positive.

L = 8 mP = 40 kN at 7 mw = 10 kN/m from 0 to 8 mx = 7 m
Mx = kN·m
11.Centroid & second moment of areaMedium
180110t = 16xdimensions in mm

A channel section lies with its open side up: a base plate 180 mm wide with two upright legs, 110 mm high overall. Base and legs are all 16 mm thick. Find its second moment of area Ix about the horizontal axis x through its centroid.

b = 180 mmh = 110 mmt = 16 mm
Ix = × 10⁶ mm⁴
12.Centroid & second moment of areaHard
1401026010xsagging Mdimensions in mm

A cast-iron beam has the T-section shown, with the flange on top. The allowable stresses are 50 MPa in tension and 120 MPa in compression. Find the largest sagging bending moment Mallow the beam can carry.

bf = 140 mmtf = 10 mmtw = 10 mmhw = 260 mmσt,allow = 50 MPaσc,allow = 120 MPa
Mallow = kN·m

3Solutions

1.Vectors: dot & cross product

Answer: a·b = −16

Dot product: a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.

Multiply matching components and add

a·b = 2·(−4) + 5·4 + (−4)·7 = (−8) + 20 + (−28) = −16

Answer

a·b = −16

Negative: the angle between the vectors is more than 90°.

2.Vectors: dot & cross product

Answer: Mz = 60 N·m

Cross product: a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.

Position vector from O to A

r = A − O = (0, −1, −1) − (3, −1, 2) = (−3, 0, −3) m

Moment M = r × F

(r × F)x = ryFz − rzFy = 0·0 − (−3)·(−20) = −60 N·m
(r × F)y = rzFx − rxFz = (−3)·50 − (−3)·0 = −150 N·m
(r × F)z = rxFy − ryFx = (−3)·(−20) − 0·50 = 60 N·m

Requested component

Mz = 60 N·m

Answer

Mz = 60 N·m
3.Beam support reactions

Answer: RA = −15 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Replace each distributed load by its resultant (its area) acting at the centroid of the load diagram, and take moments about a support to remove that support’s reaction from the equation.

Moments about A

Counter-clockwise positive.

ΣMA = 0: RB·3 = 10·1 + 65·4
RB = 270/3 = 90 kN

Vertical equilibrium

RA = 10 + 65 − 90 = −15 kN

Answer

RA = −15 kN

RA is negative: the pin at A has to hold the beam down.

4.Beam support reactions

Answer: RB = 14.75 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.

w = 2 kN/mP = 35 kNABRA​RB​3 m3 m1 m1 m

Free-body diagram

Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.

Equilibrium

Moments about A, counter-clockwise positive. Then vertical force balance.

UDL resultant: W = w·ℓ = 2·1 = 2 kN, acting at x̄ = 6.5 m
ΣMA = 0: RB·8 = 35·3 + 2·1·6.5
RB = 118/8 = 14.75 kN
ΣFy = 0: RA = 37 − 14.75 = 22.25 kN

Answer

RB = 14.75 kN
5.Truss: method of joints

Answer: FBC = −25.16 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB45 kNAy​Cy​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·8 = 45·2 → Cy = 11.25 kN
ΣFy = 0: Ay = 45 − 11.25 = 33.75 kN

Joint C

The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.

sin γ = 3/6.708 = 0.4472, cos γ = 6/6.708 = 0.8944
ΣFy = 0: Cy + FBC·sin γ = 0 → FBC = −11.25/0.4472 = −25.16 kN

Answer

FBC = −25.16 kN (compression)
6.Truss: method of joints

Answer: member CG

Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.

Joint C

BC and CD lie on one straight line and the joint carries no load. Balancing forces across that line leaves only CG.

ΣF⊥ = 0 → FCG = 0

Check with the method of joints

Solving all joints gives these member forces (T = tension, C = compression).

AB: 7.5 kN (T), BC: 25 kN (T), CD: 25 kN (T), DE: 42.5 kN (T), FG: 32.5 kN (C), GH: 67.5 kN (C), AF: 45.96 kN (C), HE: 60.1 kN (C), BF: 32.5 kN (T), CG: 0, DH: 2.5 kN (T), BG: 24.75 kN (C), DG: 24.75 kN (T)

Answer

Zero-force member: CG
7.Frames & machines

Answer: C = 15.14 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Tie force from leg BC

By = 10 kN
T = 10·2.5/2.2 = 11.36 kN

Components of the pin force on BC

Cx = T = 11.36 kN, Cy = −By = −10 kN

Magnitude

C = √(11.36² + 10²) = 15.14 kN

Answer

C = 15.14 kN
8.Frames & machines

Answer: Ax = 3.84 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Direction of BC

BC = 2.828 m, cos = 0.7071, sin = 0.7071

Whole frame: moments about A

FBC·0.7071·5 = 6·1.8 + 10·2
FBC = 8.712 kN

Horizontal balance

Ax + 10 − 8.712·0.7071 = 0
Ax = −3.84 kN → |Ax| = 3.84 kN

Answer

Ax = 3.84 kN

The minus sign means Ax points to the left.

9.Shear force & bending moment

Answer: Mx = −41.67 kN·m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut. An applied couple makes the bending moment diagram jump by the size of the couple.

Support reactions

Moments about A, counter-clockwise positive: RB·L − M0 = 0. Vertical balance: RA + RB = 0.

RB = M0/L = 50/6 = 8.333 kN (upward)
RA = −RB = −8.333 kN (downward)

Cut just left of the couple

The left part contains only RA.

Mx = RA·a = −8.333·5 = −41.67 kN·m

Answer

Mx = −41.67 kN·m
10.Shear force & bending moment

Answer: Mx = 70 kN·m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.

Support reactions

Equilibrium of the whole beam.

UDL resultant: W = w·ℓ = 10·8 = 80 kN, acting at x̄ = 4 m
ΣMA = 0: RB·8 = 40·7 + 10·8·4
RB = 600/8 = 75 kN
ΣFy = 0: RA = 120 − 75 = 45 kN
w = 10 kN/mP = 40 kNABRA​ = 45RB​ = 75section7 m1 m

Cut at x = 7 m and keep the left part

Only forces left of the cut appear. A UDL portion acts as one force at the middle of that portion.

M = RA·x − (each load left of the cut × its distance to the cut)
Mx = 45·7 − 10·7·3.5 = 70 kN·m

Answer

Mx = 70 kN·m
11.Centroid & second moment of area

Answer: Ix = 6.727 × 10⁶ mm⁴

Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.

Split into rectangles

Take the base at full width and the two legs above it (height h − t), so nothing is counted twice.

base: A1 = 180·16 = 2880 mm², y1 = 8 mm
two legs: A2 = 2·16·94 = 3008 mm², y2 = 16 + 94/2 = 63 mm

Centroid

ȳ = (2880·8 + 3008·63)/5888 = 36.1 mm

Parallel-axis theorem

base: 180·16³/12 + 2880·(8 − 36.1)² = 2.335 × 10⁶ mm⁴
two legs: 2·16·94³/12 + 3008·(63 − 36.1)² = 4.392 × 10⁶ mm⁴
Ix = 2.335 × 10⁶ + 4.392 × 10⁶
Ix = 6.727 × 10⁶ mm⁴ = 6.727 × 10⁶ mm⁴

Answer

Ix = 6.727 × 10⁶ mm⁴
12.Centroid & second moment of area

Answer: Mallow = 8.813 kN·m

Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.

Centroid

ȳ = (1400·265 + 2600·130)/4000 = 177.3 mm
top edge: c = 270 − 177.3 = 92.75 mm

Second moment of area

I = 140·10³/12 + 1400·87.75² + 10·260³/12 + 2600·47.25² = 3.124 × 10⁷ mm⁴

Moment allowed by each edge

Sagging: the top is in compression, the bottom in tension.

top edge: M = 120·3.124 × 10⁷/92.75 = 40.42 kN·m
bottom edge: M = 50·3.124 × 10⁷/177.3 = 8.813 kN·m

Governing value

Mallow = min = 8.813 kN·m (bottom edge)

Answer

Mallow = 8.813 kN·m

ExamProblems · examproblems.com/courses/statics