Statics: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Vectors: dot & cross product

Magnitude
|a| = √(ax² + ay² + az²)
Unit vector
û = a/|a|
Components from an angle
Fx = F·cos θ, Fy = F·sin θ
Dot product
a·b = axbx + ayby + azbz = |a||b|cos θ
Scalar projection of a onto b
a·b/|b|
Work
W = F·d
Cross product
a × b = (aybz − azby, azbx − axbz, axby − aybx)
Areas
parallelogram |a × b|, triangle ½|a × b|
Moment about O
MO = r × F, r = A − O
Volume of a parallelepiped
V = |a·(b × c)|

Method

  1. Write every vector in components; for a force given by a magnitude and an angle, use F·cos θ and F·sin θ.
  2. For lengths and directions use the magnitude √(x² + y² + z²) and the unit vector a/|a|.
  3. Use the dot product for angles, projections, perpendicularity and work: a·b = |a||b|cos θ.
  4. Use the cross product for perpendicular vectors, areas and moments: write the three components carefully, keeping the order a × b.

Beam support reactions

Equilibrium
ΣFx = 0, ΣFy = 0, ΣM = 0
Uniform load
resultant w·L at the middle of the load
Moment
M = F·d

Method

  1. Draw a free-body diagram and replace each support by its reactions.
  2. Replace every distributed load by a single force at its centroid.
  3. Take moments about one support to find the reaction at the other.
  4. Use ΣFy = 0 to find the remaining reaction, and check with a second moment equation.

Truss: method of joints

Method of joints
ΣFx = 0, ΣFy = 0 at each joint
Method of sections
ΣM = 0 about a cut point
Member force
positive = tension, negative = compression

Method

  1. Find the support reactions for the whole truss.
  2. Method of joints: start at a joint with at most two unknown member forces and use ΣFx = 0 and ΣFy = 0.
  3. Method of sections: cut through the member you need and take moments about a point where the other unknown members meet.
  4. Assume tension; a negative answer means compression.

Frames & machines

Equilibrium of each member
ΣFx = 0, ΣFy = 0, ΣM = 0
Two-force member
force along the line through its two pins
Pin force
equal and opposite on the two members it joins
Magnitude of a pin force
F = √(Fx² + Fy²)
Lever, pliers, bell crank
Fin·a = Fout·b
Toggle
Flink = F/(2 sin θ), Q = F/(2 tan θ)
Uniform load
resultant w·L at the middle of the load

Method

  1. Draw the whole structure and find the support reactions if there are no more than three unknowns.
  2. Spot the two-force members: loaded only at two pins, their force acts along the line between the pins.
  3. Take the frame apart and draw every member on its own, with equal and opposite pin forces where members meet.
  4. For each member, take moments about a pin with unknown forces, then use ΣFx = 0 and ΣFy = 0; combine components into a magnitude at the end.

Shear force & bending moment

Shear and moment
V = ΣF on one side, M = ΣF·d on one side
Bending stress
σ = M·y/I
Rectangle
I = bh³/12
Section modulus
W = I/ymax
Simply supported, uniform load
Mmax = wL²/8

Method

  1. Find the support reactions from equilibrium of the whole beam.
  2. Cut the beam at the section you need and keep one side.
  3. Shear force: sum of the vertical forces on that side. Bending moment: sum of their moments about the cut.
  4. For the maximum moment, find where the shear force is zero.

Centroid & second moment of area

Centroid
ȳ = ΣAiyi/ΣAi
Rectangle
I = bh³/12
Parallel-axis theorem
I = Ic + A·d²
Composite section
I = Σ(Ic,i + Aidi²)

2Practice problems

1.Vectors: dot & cross productMedium
xyzdFAB

A constant force F = (10, 15, 20) N acts on an object while it moves in a straight line from point A(−3, −2, 2) to point B(−2, 1, 5). Coordinates are in metres. Find the work W done by the force.

F = (10, 15, 20) NA(−3, −2, 2) mB(−2, 1, 5) m
W = J
2.Vectors: dot & cross productHard
xyzab

For a = (3, 4, −4) and b = (3, −2, 5), find the z-component (a × b)z of the cross product a × b.

a = (3, 4, −4)b = (3, −2, 5)
(a × b)z =
3.Beam support reactionsMedium
w0​ = 15 kN/mP = 10 kNABRB​ = ?3.5 m1.5 m

The simply supported beam (pin at A, roller at B) carries a linearly varying load that falls from 15 kN/m at A to zero at B. A point load P also acts at 3.5 m from A. Find the vertical support reaction RB.

L = 5 mw0 = 15 kN/mP = 10 kN at 3.5 m
RB = kN
4.Beam support reactionsHard
P = 25 kNQ = 50 kNADCRD​ = ?1.5 m0.5 m2.5 m1.5 m

A compound beam is fixed to the wall at A, has an internal hinge at C (2 m from A) and rests on a roller at D (6 m from A). It carries a point load P at 4.5 m from A and a point load Q at 1.5 m from A. Find the reaction RD at the roller.

AC = 2 mAD = 6 mP = 25 kN at 4.5 mQ = 50 kN at 1.5 m
RD = kN
5.Truss: method of jointsMedium
ABBCACACB10 kN8 m1 m2 m

Use the method of joints to find the force FAC in member AC. Give tension as positive and compression as negative.

span = 8 mheight = 2 mB is 1 m from Avertical load = 10 kN
FAC = kN
6.Truss: method of jointsHard
ABBCACACB40 kN30 kN5 m4 m3 m

Use the method of joints to find the force FAB in member AB. Give tension as positive and compression as negative.

span = 5 mheight = 3 mB is 4 m from Avertical load = 40 kNhorizontal load = 30 kN ←
FAB = kN
7.Frames & machinesMedium
5 kN8 m2.5 m3.6 mABCK

The frame shown has pins at A, B and C; A and C are fixed to the ground 8 m apart, and B is 2.5 m above the ground and 3.6 m to the right of A. A vertical load of 5 kN acts on member AB at K, 1.44 m (horizontally) from A. Find the force FBC in member BC.

P = 5 kNL = 8 mH = 2.5 mhorizontal distance A to B = 3.6 mhorizontal distance A to K = 1.44 m
FBC = kN
8.Frames & machinesHard
6 kN2 kN6 m1.5 mABC

A uniform horizontal boom AB of weight 2 kN is pinned to a wall at A and held by a cable from B to the point C on the wall, 1.5 m above A. A load of 6 kN hangs at B. Find the magnitude of the pin reaction A.

W = 6 kNWb = 2 kNAB = 6 mAC = 1.5 m
A = kN
9.Shear force & bending momentMedium
w = 12 kN/mABsection3 m5 m

Find the shear force Vx at the section x = 3 m from support A. Use sagging moments positive and upward shear on the left face positive.

L = 8 mw = 12 kN/m from 0 to 8 mx = 3 m
Vx = kN
10.Shear force & bending momentHard
w = 6 kN/mP = 60 kNABsection2 m1 m3 m

Find the bending moment Mx at the section x = 3 m from support A. Use sagging moments positive and upward shear on the left face positive.

L = 6 mP = 60 kN at 2 mw = 6 kN/m from 0 to 6 mx = 3 m
Mx = kN·m
11.Centroid & second moment of areaMedium
150 mm200 mm60 mmØ50xIx​ = ?

A 150 mm × 200 mm plate has a circular hole of diameter 50 mm on its vertical centre line, with its centre 60 mm above the bottom. Find the second moment of area Ix about the horizontal axis through the centroid.

b = 150 mmh = 200 mmd = 50 mmhole centre: y = 60 mm
Ix = × 10⁶ mm⁴
12.Centroid & second moment of areaHard
3001024012xhogging Mdimensions in mm

A cast-iron beam has the T-section shown, with the flange on top. The allowable stresses are 40 MPa in tension and 150 MPa in compression. Find the largest hogging bending moment Mallow the beam can carry (give its size).

bf = 300 mmtf = 10 mmtw = 12 mmhw = 240 mmσt,allow = 40 MPaσc,allow = 150 MPa
Mallow = kN·m

3Solutions

1.Vectors: dot & cross product

Answer: W = 115 J

Dot product: a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.

Displacement

d = B − A = (−2, 1, 5) − (−3, −2, 2) = (1, 3, 3) m

Work

W = F·d = 10·1 + 15·3 + 20·3 = 115 J

Answer

W = 115 J
2.Vectors: dot & cross product

Answer: (a × b)z = −18

Cross product: a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.

Cross product, component by component

(a × b)x = aybz − azby = 4·5 − (−4)·(−2) = 12
(a × b)y = azbx − axbz = (−4)·3 − 3·5 = −27
(a × b)z = axby − aybx = 3·(−2) − 4·3 = −18

Requested component

(a × b)z = −18

Answer

(a × b)z = −18

Check: a × b is perpendicular to both vectors, so its dot product with a and with b is zero.

3.Beam support reactions

Answer: RB = 19.5 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Replace each distributed load by its resultant (its area) acting at the centroid of the load diagram, and take moments about a support to remove that support’s reaction from the equation.

Resultant of the triangular load

W = ½·15·5 = 37.5 kN
x̄ = L/3 = 1.667 m

Equilibrium

Moments about A, counter-clockwise positive. Then vertical force balance.

ΣMA = 0: RB·5 = 37.5·1.667 + 10·3.5
RB = 19.5 kN
RA = 47.5 − 19.5 = 28 kN

Answer

RB = 19.5 kN
4.Beam support reactions

Answer: RD = 15.63 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Replace each distributed load by its resultant (its area) acting at the centroid of the load diagram, and take moments about a support to remove that support’s reaction from the equation. An internal hinge cannot carry a bending moment, which gives one extra equation: the moment about the hinge of the forces on either side is zero.

Part CD

The hinge has no moment, so moments about C on CD alone must balance.

ΣMC = 0: RD·4 = 25·2.5
RD = 15.63 kN
VC = 25 − 15.63 = 9.375 kN

Answer

RD = 15.63 kN
5.Truss: method of joints

Answer: FAC = 4.375 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB10 kNAy​Cy​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·8 = 10·1 → Cy = 1.25 kN
ΣFy = 0: Ay = 10 − 1.25 = 8.75 kN

Joint C

The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.

sin γ = 2/7.28 = 0.2747, cos γ = 7/7.28 = 0.9615
ΣFy = 0: Cy + FBC·sin γ = 0 → FBC = −1.25/0.2747 = −4.55 kN
ΣFx = 0: −FAC − FBC·cos γ = 0 → FAC = −(−4.55)·0.9615 = 4.375 kN

Answer

FAC = 4.375 kN (tension)
6.Truss: method of joints

Answer: FAB = −43.33 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB40 kN30 kNAy​Cy​Ax​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·5 = 40·4 − 30·3 → Cy = 14 kN
ΣFy = 0: Ay = 40 − 14 = 26 kN
ΣFx = 0: Ax = 30 kN

Joint A

Assume every member is in tension (pulling away from the joint). Only AB has a vertical component at A.

sin α = 3/5 = 0.6
ΣFy = 0: Ay + FAB·sin α = 0
FAB = −26/0.6 = −43.33 kN

Answer

FAB = −43.33 kN (compression)
7.Frames & machines

Answer: FBC = 1.822 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Two-force member BC

BC = √(4.4² + 2.5²) = 5.061 m

Whole frame: moments about A

The ground pushes on BC at C along CB; its horizontal component passes through A, only the vertical one has a moment.

FBC·(2.5/5.061)·8 = 5·1.44
FBC = 1.822 kN (compression)

Answer

FBC = 1.822 kN
8.Frames & machines

Answer: A = 28.02 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Cable tension

T = (6 + 2/2)/0.2425 = 28.86 kN

Components at A

Ax = T·cos β = 28 kN
Ay = 6 + 2 − T·sin β = 1 kN

Magnitude

A = √(28² + 1²) = 28.02 kN

Answer

A = 28.02 kN
9.Shear force & bending moment

Answer: Vx = 12 kN

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.

Support reactions

Equilibrium of the whole beam.

UDL resultant: W = w·ℓ = 12·8 = 96 kN, acting at x̄ = 4 m
ΣMA = 0: RB·8 = 12·8·4
RB = 384/8 = 48 kN
ΣFy = 0: RA = 96 − 48 = 48 kN
w = 12 kN/mABRA​ = 48RB​ = 48section3 m5 m

Cut at x = 3 m and keep the left part

Only forces left of the cut appear. A UDL portion acts as one force at the middle of that portion.

V = RA − (all downward loads left of the cut)
Vx = 48 − 12·3 = 12 kN

Answer

Vx = 12 kN
10.Shear force & bending moment

Answer: Mx = 87 kN·m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.

Support reactions

Equilibrium of the whole beam.

UDL resultant: W = w·ℓ = 6·6 = 36 kN, acting at x̄ = 3 m
ΣMA = 0: RB·6 = 60·2 + 6·6·3
RB = 228/6 = 38 kN
ΣFy = 0: RA = 96 − 38 = 58 kN
w = 6 kN/mP = 60 kNABRA​ = 58RB​ = 38section2 m1 m3 m

Cut at x = 3 m and keep the left part

Only forces left of the cut appear. A UDL portion acts as one force at the middle of that portion.

M = RA·x − (each load left of the cut × its distance to the cut)
Mx = 58·3 − 60·(3 − 2) − 6·3·1.5 = 87 kN·m

Answer

Mx = 87 kN·m
11.Centroid & second moment of area

Answer: Ix = 96.33 × 10⁶ mm⁴

Sections with holes: treat a hole as a negative area. The centroid is ȳ = (A₁y₁ − A₂y₂)/(A₁ − A₂), with A₁, y₁ for the full plate and A₂, y₂ for the hole. For the second moment of area about the centroidal axis, use the parallel-axis theorem for each part and subtract the hole: I = (Ic1 + A₁d₁²) − (Ic2 + A₂d₂²), where d is the distance from each part's own centroid to the axis through ȳ. A rectangle has Ic = bh³/12 and a circle Ic = πd⁴/64.

Centroid

ȳ = (30000·100 − 1963·60)/(30000 − 1963) = 102.8 mm

Full plate about ȳ

150·200³/12 + 30000·−2.801² = 100.2 × 10⁶ mm⁴

Hole about ȳ

π·50⁴/64 + 1963·−42.8² = 3.904 × 10⁶ mm⁴

Subtract

Ix = 96.33 × 10⁶ mm⁴

Answer

Ix = 96.33 × 10⁶ mm⁴
12.Centroid & second moment of area

Answer: Mallow = 22.23 kN·m

Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.

Centroid

ȳ = (3000·245 + 2880·120)/5880 = 183.8 mm
top edge: c = 250 − 183.8 = 66.22 mm

Second moment of area

I = 300·10³/12 + 3000·61.22² + 12·240³/12 + 2880·63.78² = 3.681 × 10⁷ mm⁴

Moment allowed by each edge

Hogging: the top is in tension, the bottom in compression.

top edge: M = 40·3.681 × 10⁷/66.22 = 22.23 kN·m
bottom edge: M = 150·3.681 × 10⁷/183.8 = 30.04 kN·m

Governing value

Mallow = min = 22.23 kN·m (top edge)

Answer

Mallow = 22.23 kN·m

ExamProblems · examproblems.com/courses/statics