In the print window, choose “Save as PDF” to keep a copy on your device.
1Formulas and methods
Vectors: dot & cross product
Magnitude
|a| = √(ax² + ay² + az²)
Unit vector
û = a/|a|
Components from an angle
Fx = F·cos θ, Fy = F·sin θ
Dot product
a·b = axbx + ayby + azbz = |a||b|cos θ
Scalar projection of a onto b
a·b/|b|
Work
W = F·d
Cross product
a × b = (aybz − azby, azbx − axbz, axby − aybx)
Areas
parallelogram |a × b|, triangle ½|a × b|
Moment about O
MO = r × F, r = A − O
Volume of a parallelepiped
V = |a·(b × c)|
Method
Write every vector in components; for a force given by a magnitude and an angle, use F·cos θ and F·sin θ.
For lengths and directions use the magnitude √(x² + y² + z²) and the unit vector a/|a|.
Use the dot product for angles, projections, perpendicularity and work: a·b = |a||b|cos θ.
Use the cross product for perpendicular vectors, areas and moments: write the three components carefully, keeping the order a × b.
Beam support reactions
Equilibrium
ΣFx = 0, ΣFy = 0, ΣM = 0
Uniform load
resultant w·L at the middle of the load
Moment
M = F·d
Method
Draw a free-body diagram and replace each support by its reactions.
Replace every distributed load by a single force at its centroid.
Take moments about one support to find the reaction at the other.
Use ΣFy = 0 to find the remaining reaction, and check with a second moment equation.
Truss: method of joints
Method of joints
ΣFx = 0, ΣFy = 0 at each joint
Method of sections
ΣM = 0 about a cut point
Member force
positive = tension, negative = compression
Method
Find the support reactions for the whole truss.
Method of joints: start at a joint with at most two unknown member forces and use ΣFx = 0 and ΣFy = 0.
Method of sections: cut through the member you need and take moments about a point where the other unknown members meet.
Assume tension; a negative answer means compression.
Frames & machines
Equilibrium of each member
ΣFx = 0, ΣFy = 0, ΣM = 0
Two-force member
force along the line through its two pins
Pin force
equal and opposite on the two members it joins
Magnitude of a pin force
F = √(Fx² + Fy²)
Lever, pliers, bell crank
Fin·a = Fout·b
Toggle
Flink = F/(2 sin θ), Q = F/(2 tan θ)
Uniform load
resultant w·L at the middle of the load
Method
Draw the whole structure and find the support reactions if there are no more than three unknowns.
Spot the two-force members: loaded only at two pins, their force acts along the line between the pins.
Take the frame apart and draw every member on its own, with equal and opposite pin forces where members meet.
For each member, take moments about a pin with unknown forces, then use ΣFx = 0 and ΣFy = 0; combine components into a magnitude at the end.
Shear force & bending moment
Shear and moment
V = ΣF on one side, M = ΣF·d on one side
Bending stress
σ = M·y/I
Rectangle
I = bh³/12
Section modulus
W = I/ymax
Simply supported, uniform load
Mmax = wL²/8
Method
Find the support reactions from equilibrium of the whole beam.
Cut the beam at the section you need and keep one side.
Shear force: sum of the vertical forces on that side. Bending moment: sum of their moments about the cut.
For the maximum moment, find where the shear force is zero.
Centroid & second moment of area
Centroid
ȳ = ΣAiyi/ΣAi
Rectangle
I = bh³/12
Parallel-axis theorem
I = Ic + A·d²
Composite section
I = Σ(Ic,i + Aidi²)
2Practice problems
1.Vectors: dot & cross productMedium
A constant force F = (15, −5, −5) N acts on an object while it moves in a straight line from point A(0, 4, 2) to point B(4, 5, 3). Coordinates are in metres. Find the work W done by the force.
F = (15, −5, −5) NA(0, 4, 2) mB(4, 5, 3) m
W = J
2.Vectors: dot & cross productHard
A force F = (60, 60, 40) N acts at point A(−4, −4, −1). Coordinates are in metres. Find the y-component My of the moment of the force about the origin O(0, 0, 0).
F = (60, 60, 40) NA(−4, −4, −1) mO(0, 0, 0) m
My = N·m
3.Beam support reactionsMedium
The beam has a pin at A and a roller at B, 6 m from A, and overhangs B to the free end C. Find the vertical reaction RB, taking upward as positive.
AB = 6 mAC = 8 mP1 = 45 kN at 5 mP2 = 10 kN at 8 m
RB = kN
4.Beam support reactionsHard
The cantilever beam is fixed to the wall at A. It carries a linearly varying load that is zero at the wall and rises to 4 kN/m at the free end B, plus a point load P at 4 m from the wall. Find the magnitude of the reaction moment MA at the wall.
L = 8 mw0 = 4 kN/mP = 30 kN at 4 m
MA = kN·m
5.Truss: method of jointsMedium
Use the method of joints to find the force FAB in member AB. Give tension as positive and compression as negative.
span = 5 mheight = 2 mB is 3 m from Avertical load = 45 kN
FAB = kN
6.Truss: method of jointsHard
Use the method of joints to find the force FBC in member BC. Give tension as positive and compression as negative.
span = 6 mheight = 3 mB is 5 m from Avertical load = 55 kNhorizontal load = 20 kN ←
FBC = kN
7.Frames & machinesMedium
In the toggle clamp shown, two equal links AB and BC are pinned together at B, and each makes 30° with the line AC. A downward force of 150 N is applied at B. The slider C presses on a workpiece. Neglecting friction and weights, find the horizontal clamping force Q.
F = 150 Nθ = 30°
Q = N
8.Frames & machinesHard
A uniform horizontal boom AB of weight 1 kN is pinned to a wall at A and held by a cable from B to the point C on the wall, 1.5 m above A. A load of 6 kN hangs at B. Find the magnitude of the pin reaction A.
W = 6 kNWb = 1 kNAB = 3 mAC = 1.5 m
A = kN
9.Shear force & bending momentMedium
The cantilever is fixed at A. It carries a uniformly distributed load w over its whole length and a point load P at 3 m from A. Find the bending moment MA at the fixed support A. Use sagging moments positive and upward shear on the left face positive.
L = 3 mP = 25 kN at 3 mw = 12 kN/m from 0 to 3 m
MA = kN·m
10.Shear force & bending momentHard
The marks A to G split the beam into six equal parts. At which mark is the bending moment largest in size, sagging or hogging? Click it in the diagram.
50 kN @ 12 m45 kN @ 4 m15 kN/m, 0–8 m
1A (x = 0 m)
2B (x = 2 m)
3C (x = 4 m)
4D (x = 6 m)
5E (x = 8 m)
6F (x = 10 m)
7G (x = 12 m)
11.Centroid & second moment of areaMedium
A 150 mm × 240 mm plate has a circular hole of diameter 30 mm on its vertical centre line, with its centre 144 mm above the bottom. Find the second moment of area Ix about the horizontal axis through the centroid.
b = 150 mmh = 240 mmd = 30 mmhole centre: y = 144 mm
Ix = × 10⁶ mm⁴
12.Centroid & second moment of areaHard
A 200 mm × 240 mm plate has a rectangular cut-out 80 mm wide and 20 mm high, centred on the vertical centre line with its centre 156 mm above the bottom. Find the second moment of area Ix about the horizontal axis through the centroid.
b = 200 mmh = 240 mmcut-out: 80 × 20 mmhole centre: y = 156 mm
Ix = × 10⁶ mm⁴
3Solutions
1.Vectors: dot & cross product
Answer: W = 50 J
Dot product:a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.
Displacement
d = B − A = (4, 5, 3) − (0, 4, 2) = (4, 1, 1) m
Work
W = F·d = 15·4 + (−5)·1 + (−5)·1 = 50 J
Answer
W = 50 J
2.Vectors: dot & cross product
Answer: My = 100 N·m
Cross product:a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.
Position vector from O to A
r = A − O = (−4, −4, −1) − (0, 0, 0) = (−4, −4, −1) m
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Replace each distributed load by its resultant (its area) acting at the centroid of the load diagram, and take moments about a support to remove that support’s reaction from the equation.
Moments about A
Counter-clockwise positive.
ΣMA = 0: RB·6 = 45·5 + 10·8
RB = 305/6 = 50.83 kN
Vertical equilibrium
RA = 45 + 10 − 50.83 = 4.167 kN
Answer
RB = 50.83 kN
4.Beam support reactions
Answer: MA = 205.3 kN·m
Cantilever equilibrium: a fixed support can push up and also resist rotation, so it gives a vertical reaction RA and a reaction moment MA. ΣFy = 0 gives RA, and moments about the wall give MA = Σ(load × distance from the wall). A distributed load acts as its resultant at the centroid of the load diagram.
Resultant of the triangular load
W = ½·4·8 = 16 kN
x̄ = 2L/3 = 5.333 m
Moment about the wall
MA = W·x̄ + P·a = 16·5.333 + 30·4 = 205.3 kN·m
Answer
MA = 205.3 kN·m
5.Truss: method of joints
Answer: FAB = −32.45 kN
Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.
Support reactions
Equilibrium of the whole truss. Moments about A, counter-clockwise positive.
ΣMA = 0: Cy·5 = 45·3 → Cy = 27 kN
ΣFy = 0: Ay = 45 − 27 = 18 kN
Joint A
Assume every member is in tension (pulling away from the joint). Only AB has a vertical component at A.
sin α = 2/3.606 = 0.5547
ΣFy = 0: Ay + FAB·sin α = 0
FAB = −18/0.5547 = −32.45 kN
Answer
FAB = −32.45 kN (compression)
6.Truss: method of joints
Answer: FBC = −37.77 kN
Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.
Support reactions
Equilibrium of the whole truss. Moments about A, counter-clockwise positive.
ΣMA = 0: Cy·6 = 55·5 − 20·3 → Cy = 35.83 kN
ΣFy = 0: Ay = 55 − 35.83 = 19.17 kN
ΣFx = 0: Ax = 20 kN
Joint C
The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.
sin γ = 3/3.162 = 0.9487, cos γ = 1/3.162 = 0.3162
Machines: pliers, levers, linkages and clamps turn an input force into a larger or a differently directed output force. Draw one part as a free body and take moments about its pivot: the pin force drops out, and Fin·a = Fout·b gives the mechanical advantage a/b. The pin force then follows from ΣF = 0 on the same part. In a toggle, two links meet at a shallow angle θ; each link is a two-force member, so a small force F at the joint creates large link forces F/(2 sin θ) and a clamping force F/(2 tan θ).
Equilibrium of pin B
2·Flink·sin 30° = 150
Flink = 150 N
Clamping force
Q = Flink·cos 30° = 150/(2·tan 30°) = 129.9 N
Answer
Q = 129.9 N
The force ratio Q/F = 0.866 grows without limit as the links straighten.
8.Frames & machines
Answer: A = 13.01 kN
Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.
Cable tension
T = (6 + 1/2)/0.4472 = 14.53 kN
Components at A
Ax = T·cos β = 13 kN
Ay = 6 + 1 − T·sin β = 0.5 kN
Magnitude
A = √(13² + 0.5²) = 13.01 kN
Answer
A = 13.01 kN
9.Shear force & bending moment
Answer: MA = −129 kN·m
Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.
Keep the free-end part
P: −25·3 = −75 kN·m
w: −12·3²/2 = −54 kN·m
MA = −75 − 54 = −129 kN·m
Answer
MA = −129 kN·m
Negative means hogging: tension on the top face.
10.Shear force & bending moment
Answer: E (x = 8 m)
Largest bending moment: M changes slope wherever the shear force changes, so its peaks sit where the shear force crosses zero: under a point load, inside a distributed load, or over a support of an overhang. At a fixed support of a cantilever the moment is largest at the wall. Compare the size of M at those places, sagging or hogging.
Support reactions
Take moments about one support, then use the vertical force balance.
R1 = 57.5 kN, R2 = 157.5 kN
Bending moment at every mark
Sum the moments of all forces on one side of the cut. Sagging is positive, hogging negative.
MA = 0, MB = 85, MC = 110, MD = −15, ME = −200 kN·m, MF = −100, MG = 0
Answer
Mark E: ME = −200 kN·m
11.Centroid & second moment of area
Answer: Ix = 172.3 × 10⁶ mm⁴
Sections with holes: treat a hole as a negative area. The centroid is ȳ = (A₁y₁ − A₂y₂)/(A₁ − A₂), with A₁, y₁ for the full plate and A₂, y₂ for the hole. For the second moment of area about the centroidal axis, use the parallel-axis theorem for each part and subtract the hole: I = (Ic1 + A₁d₁²) − (Ic2 + A₂d₂²), where d is the distance from each part's own centroid to the axis through ȳ. A rectangle has Ic = bh³/12 and a circle Ic = πd⁴/64.
Centroid
ȳ = (36000·120 − 706.9·144)/(36000 − 706.9) = 119.5 mm
Full plate about ȳ
150·240³/12 + 36000·0.4807² = 172.8 × 10⁶ mm⁴
Hole about ȳ
π·30⁴/64 + 706.9·24.48² = 0.4634 × 10⁶ mm⁴
Subtract
Ix = 172.3 × 10⁶ mm⁴
Answer
Ix = 172.3 × 10⁶ mm⁴
12.Centroid & second moment of area
Answer: Ix = 228.2 × 10⁶ mm⁴
Sections with holes: treat a hole as a negative area. The centroid is ȳ = (A₁y₁ − A₂y₂)/(A₁ − A₂), with A₁, y₁ for the full plate and A₂, y₂ for the hole. For the second moment of area about the centroidal axis, use the parallel-axis theorem for each part and subtract the hole: I = (Ic1 + A₁d₁²) − (Ic2 + A₂d₂²), where d is the distance from each part's own centroid to the axis through ȳ. A rectangle has Ic = bh³/12 and a circle Ic = πd⁴/64.
Centroid
ȳ = (48000·120 − 1600·156)/(48000 − 1600) = 118.8 mm