In the toggle clamp shown, two equal links AB and BC are pinned together at B, and each makes 12° with the line AC. A downward force of 500 N is applied at B. The slider C presses on a workpiece. Neglecting friction and weights, find the horizontal clamping force Q.
F = 500 Nθ = 12°
Q = N
8.Frames & machinesHard
The A-frame shown stands on a pin at A and a roller at B, 4 m apart. The legs meet at the pin C, 3 m high, and are tied by the horizontal bar DE at 1.2 m. A horizontal force of 15 kN to the right acts at C. Find the tension T in the tie.
P = 15 kNAB = 4 mheight of C = 3 mheight of DE = 1.2 m
T = kN
9.Shear force & bending momentMedium
Find the bending moment Mx at the section x = 1.5 m from support A. Use sagging moments positive and upward shear on the left face positive.
L = 8 mw = 6 kN/m from 0 to 8 mx = 1.5 m
Mx = kN·m
10.Shear force & bending momentHard
The beam rests on a pin at A and a roller at B and overhangs B by 2 m to the free end C. A uniformly distributed load w acts over the whole length A–C. Find the maximum sagging bending moment Mmax between the supports.
L = 8 mw = 2 kN/m from 0 to 8 msupports at x = 0 and x = 6 m
Mmax = kN·m
11.Centroid & second moment of areaMedium
A hollow rectangular (box) section has outer width B = 180 mm, outer height H = 350 mm and a uniform wall thickness t = 20 mm. Find its radius of gyration r about the horizontal centroidal axis.
B = 180 mmH = 350 mmt = 20 mm
r = mm
12.Centroid & second moment of areaHard
A symmetric I-section has flanges 190 mm wide and 14 mm thick, an overall depth of 380 mm and a web 10 mm thick. It carries a bending moment of 80 kN·m about the axis x. Find the size of the maximum bending stress σmax in the section.
Dot product:a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.
Dot product equals zero
a·b = (−2)·(−1) + 5·5 + (−2)·k = 0
27 + (−2)·k = 0
Solve for k
k = −27/(−2) = 13.5
Answer
k = 13.5
2.Vectors: dot & cross product
Answer: (a × b)x = 2
Cross product:a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.
Cross product, component by component
(a × b)x = aybz − azby = 1·2 − 0·(−6) = 2
(a × b)y = azbx − axbz = 0·(−6) − (−2)·2 = 4
(a × b)z = axby − aybx = (−2)·(−6) − 1·(−6) = 18
Requested component
(a × b)x = 2
Answer
(a × b)x = 2
Check: a × b is perpendicular to both vectors, so its dot product with a and with b is zero.
3.Beam support reactions
Answer: RB = 26.88 kN
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.
Free-body diagram
Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.
Equilibrium
Moments about A, counter-clockwise positive. Then vertical force balance.
ΣMA = 0: RB·8 = 35·1 + 60·3
RB = 215/8 = 26.88 kN
ΣFy = 0: RA = 95 − 26.88 = 68.13 kN
Answer
RB = 26.88 kN
4.Beam support reactions
Answer: RA = 15 kN
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.
Free-body diagram
Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.
Equilibrium
Moments about A, counter-clockwise positive. Then vertical force balance.
UDL resultant: W = w·ℓ = 8·3 = 24 kN, acting at x̄ = 5.5 m
ΣMA = 0: RB·8 = 15·4 + 8·3·5.5
RB = 192/8 = 24 kN
ΣFy = 0: RA = 39 − 24 = 15 kN
Answer
RA = 15 kN
5.Truss: method of joints
Answer: FBC = −8.485 kN
Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.
Support reactions
Equilibrium of the whole truss. Moments about A, counter-clockwise positive.
ΣMA = 0: Cy·5 = 10·3 → Cy = 6 kN
ΣFy = 0: Ay = 10 − 6 = 4 kN
Joint C
The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.
sin γ = 2/2.828 = 0.7071, cos γ = 2/2.828 = 0.7071
Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.
Joint C
BC and CD lie on one straight line and the joint carries no load. Balancing forces across that line leaves only CG.
ΣF⊥ = 0 → FCG = 0
Check with the method of joints
Solving all joints gives these member forces (T = tension, C = compression).
Machines: pliers, levers, linkages and clamps turn an input force into a larger or a differently directed output force. Draw one part as a free body and take moments about its pivot: the pin force drops out, and Fin·a = Fout·b gives the mechanical advantage a/b. The pin force then follows from ΣF = 0 on the same part. In a toggle, two links meet at a shallow angle θ; each link is a two-force member, so a small force F at the joint creates large link forces F/(2 sin θ) and a clamping force F/(2 tan θ).
Equilibrium of pin B
2·Flink·sin 12° = 500
Flink = 1202 N
Clamping force
Q = Flink·cos 12° = 500/(2·tan 12°) = 1176 N
Answer
Q = 1176 N
The force ratio Q/F = 2.352 grows without limit as the links straighten.
8.Frames & machines
Answer: T = 12.5 kN
Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.
Whole frame: moments about A
By·4 = 15·3
By = 11.25 kN
Leg BC: moments about C
11.25·2 = T·1.8
T = 12.5 kN
Answer
T = 12.5 kN
A positive T means the tie is in tension, as assumed.
9.Shear force & bending moment
Answer: Mx = 29.25 kN·m
Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.
Support reactions
Equilibrium of the whole beam.
UDL resultant: W = w·ℓ = 6·8 = 48 kN, acting at x̄ = 4 m
ΣMA = 0: RB·8 = 6·8·4
RB = 192/8 = 24 kN
ΣFy = 0: RA = 48 − 24 = 24 kN
Cut at x = 1.5 m and keep the left part
Only forces left of the cut appear. A UDL portion acts as one force at the middle of that portion.
M = RA·x − (each load left of the cut × its distance to the cut)
Mx = 24·1.5 − 6·1.5·0.75 = 29.25 kN·m
Answer
Mx = 29.25 kN·m
10.Shear force & bending moment
Answer: Mmax = 7.111 kN·m
Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut. Maximum moment: since dM/dx = V, the bending moment has its peak where the shear force passes through zero, either at a point load or inside a distributed load.
Support reactions
Equilibrium of the whole beam, including the load on the overhang.
UDL resultant: W = w·ℓ = 2·8 = 16 kN, acting at x̄ = 4 m
Second moment of area: for a rectangle about its own centroidal axis I = bh³/12, and about its base bh³/3 (parallel-axis theorem I = Ic + A·d²). A hole is handled by subtracting its I, as long as both parts share the same axis. The elastic section modulus is S = I/c, where c is the distance to the extreme fibre. The radius of gyration r = √(I/A) is the distance at which the whole area would give the same I; it is used in column buckling.
Net area and second moment of area
b = 140 mm, h = 310 mm
A = BH − bh = 180·350 − 140·310 = 19600 mm²
I = (BH³ − bh³)/12 = 2.956 × 10⁸ mm⁴
Radius of gyration
r = √(I/A) = √(2.956 × 10⁸/19600) = 122.8 mm
Answer
r = 122.8 mm
12.Centroid & second moment of area
Answer: σmax = 70.83 MPa
Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.
Outer rectangle minus the two side cut-outs
Both cut-outs together are (B − tw) wide and hw = H − 2tf high, and share the axis x.