Statics: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Vectors: dot & cross product

Magnitude
|a| = √(ax² + ay² + az²)
Unit vector
û = a/|a|
Components from an angle
Fx = F·cos θ, Fy = F·sin θ
Dot product
a·b = axbx + ayby + azbz = |a||b|cos θ
Scalar projection of a onto b
a·b/|b|
Work
W = F·d
Cross product
a × b = (aybz − azby, azbx − axbz, axby − aybx)
Areas
parallelogram |a × b|, triangle ½|a × b|
Moment about O
MO = r × F, r = A − O
Volume of a parallelepiped
V = |a·(b × c)|

Method

  1. Write every vector in components; for a force given by a magnitude and an angle, use F·cos θ and F·sin θ.
  2. For lengths and directions use the magnitude √(x² + y² + z²) and the unit vector a/|a|.
  3. Use the dot product for angles, projections, perpendicularity and work: a·b = |a||b|cos θ.
  4. Use the cross product for perpendicular vectors, areas and moments: write the three components carefully, keeping the order a × b.

Beam support reactions

Equilibrium
ΣFx = 0, ΣFy = 0, ΣM = 0
Uniform load
resultant w·L at the middle of the load
Moment
M = F·d

Method

  1. Draw a free-body diagram and replace each support by its reactions.
  2. Replace every distributed load by a single force at its centroid.
  3. Take moments about one support to find the reaction at the other.
  4. Use ΣFy = 0 to find the remaining reaction, and check with a second moment equation.

Truss: method of joints

Method of joints
ΣFx = 0, ΣFy = 0 at each joint
Method of sections
ΣM = 0 about a cut point
Member force
positive = tension, negative = compression

Method

  1. Find the support reactions for the whole truss.
  2. Method of joints: start at a joint with at most two unknown member forces and use ΣFx = 0 and ΣFy = 0.
  3. Method of sections: cut through the member you need and take moments about a point where the other unknown members meet.
  4. Assume tension; a negative answer means compression.

Frames & machines

Equilibrium of each member
ΣFx = 0, ΣFy = 0, ΣM = 0
Two-force member
force along the line through its two pins
Pin force
equal and opposite on the two members it joins
Magnitude of a pin force
F = √(Fx² + Fy²)
Lever, pliers, bell crank
Fin·a = Fout·b
Toggle
Flink = F/(2 sin θ), Q = F/(2 tan θ)
Uniform load
resultant w·L at the middle of the load

Method

  1. Draw the whole structure and find the support reactions if there are no more than three unknowns.
  2. Spot the two-force members: loaded only at two pins, their force acts along the line between the pins.
  3. Take the frame apart and draw every member on its own, with equal and opposite pin forces where members meet.
  4. For each member, take moments about a pin with unknown forces, then use ΣFx = 0 and ΣFy = 0; combine components into a magnitude at the end.

Shear force & bending moment

Shear and moment
V = ΣF on one side, M = ΣF·d on one side
Bending stress
σ = M·y/I
Rectangle
I = bh³/12
Section modulus
W = I/ymax
Simply supported, uniform load
Mmax = wL²/8

Method

  1. Find the support reactions from equilibrium of the whole beam.
  2. Cut the beam at the section you need and keep one side.
  3. Shear force: sum of the vertical forces on that side. Bending moment: sum of their moments about the cut.
  4. For the maximum moment, find where the shear force is zero.

Centroid & second moment of area

Centroid
ȳ = ΣAiyi/ΣAi
Rectangle
I = bh³/12
Parallel-axis theorem
I = Ic + A·d²
Composite section
I = Σ(Ic,i + Aidi²)

2Practice problems

1.Vectors: dot & cross productMedium
xyzab

Find the scalar projection compb a of a = (−6, 2, 7) onto b = (−5, −5, 2), that is, the component of a in the direction of b.

a = (−6, 2, 7)b = (−5, −5, 2)
compb a =
2.Vectors: dot & cross productHard
xyzrFOA

A force F = (10, −40, 60) N acts at point A(4, 1, 3). Coordinates are in metres. Find the y-component My of the moment of the force about the origin O(0, 0, 0).

F = (10, −40, 60) NA(4, 1, 3) mO(0, 0, 0) m
My = N·m
3.Beam support reactionsMedium
w0​ = 12 kN/mP = 80 kNABRA​ = ?3.5 m1.5 m

The simply supported beam (pin at A, roller at B) carries a linearly varying load that rises from zero at A to 12 kN/m at B. A point load P also acts at 3.5 m from A. Find the vertical support reaction RA.

L = 5 mw0 = 12 kN/mP = 80 kN at 3.5 m
RA = kN
4.Beam support reactionsHard
P = 30 kN, 30°Q = 40 kNABRA​ = ?4 m2 m2 m

The simply supported beam has a pin at A and a roller at B. A load P acts at 6 m from A, inclined at 30° to the horizontal, and a vertical load Q acts at 4 m from A. Find the magnitude of the total reaction force RA at the pin A.

L = 8 mP = 30 kN at 6 m, θ = 30°Q = 40 kN at 4 m
RA = kN
5.Truss: method of jointsMedium
ABBCACACB30 kN4 m3 m2 m

Use the method of joints to find the force FBC in member BC. Give tension as positive and compression as negative.

span = 4 mheight = 2 mB is 3 m from Avertical load = 30 kN
FBC = kN
6.Truss: method of jointsHard
ABBCACACB60 kN15 kN6 m2 m3 m

Use the method of joints to find the force FAB in member AB. Give tension as positive and compression as negative.

span = 6 mheight = 3 mB is 2 m from Avertical load = 60 kNhorizontal load = 15 kN →
FAB = kN
7.Frames & machinesMedium
4 kN1.6 m1.4 m1.5 mABCD

A horizontal beam AB is pinned to a wall at A and propped by the strut CD, pinned to the wall at C, 1.5 m below A. A load of 4 kN hangs at B. Neglect the weights. Find the magnitude of the pin force A on the beam at A.

P = 4 kNAD = 1.6 mAB = 3 mAC = 1.5 m
A = kN
8.Frames & machinesHard
5 kN10 kN8 m3 m2.4 mABCK

The frame shown has pins at A, B and C; A and C are fixed to the ground 8 m apart, and B is 3 m high and 2.4 m to the right of A. Member AB carries a vertical load of 5 kN at K, 1.44 m (horizontally) from A, and a horizontal load of 10 kN to the right acts at B on member AB. Find the size of the horizontal reaction Ax at A.

P = 5 kNQ = 10 kNL = 8 mH = 3 mhorizontal distance A to B = 2.4 mhorizontal distance A to K = 1.44 m
Ax = kN
9.Shear force & bending momentMedium
M0​ = 50 kN·mAB2 m6 m

The simply supported beam carries a clockwise couple M0 = 50 kN·m at x = 2 m from A, and no other load. Find the bending moment Mx just to the left of the couple. Use sagging moments positive and upward shear on the left face positive.

L = 8 mM0 = 50 kN·m clockwise, at 2 m
Mx = kN·m
10.Shear force & bending momentHard
4 kN/m20 kN35 kN10 kNABCDEFG1 m1 m1 m1 m1 m1 m

The marks A to G split the beam into six equal parts. At which mark is the bending moment largest in size, sagging or hogging? Click it in the diagram.

20 kN @ 0 m35 kN @ 6 m10 kN @ 3 m4 kN/m, 1–4 m
  1. 1A (x = 0 m)
  2. 2B (x = 1 m)
  3. 3C (x = 2 m)
  4. 4D (x = 3 m)
  5. 5E (x = 4 m)
  6. 6F (x = 5 m)
  7. 7G (x = 6 m)
11.Centroid & second moment of areaMedium
1602001214xdimensions in mm

A symmetric I-section has flanges 160 mm wide and 12 mm thick, an overall depth of 200 mm and a web 14 mm thick. Find its elastic section modulus Sx for bending about the horizontal centroidal axis x.

B = 160 mmH = 200 mmtf = 12 mmtw = 14 mm
Sx = × 10³ mm³
12.Centroid & second moment of areaHard
150 mm240 mm96 mm80 × 20xIx​ = ?

A 150 mm × 240 mm plate has a rectangular cut-out 80 mm wide and 20 mm high, centred on the vertical centre line with its centre 96 mm above the bottom. Find the second moment of area Ix about the horizontal axis through the centroid.

b = 150 mmh = 240 mmcut-out: 80 × 20 mmhole centre: y = 96 mm
Ix = × 10⁶ mm⁴

3Solutions

1.Vectors: dot & cross product

Answer: compb a = 4.627

Dot product: a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.

Dot product

a·b = (−6)·(−5) + 2·(−5) + 7·2 = 34

Length of b

|b| = √((−5)² + (−5)² + 2²) = 7.348

Scalar projection

compb a = a·b/|b| = 34/7.348 = 4.627

Answer

compb a = 4.627
2.Vectors: dot & cross product

Answer: My = −210 N·m

Cross product: a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.

Position vector from O to A

r = A − O = (4, 1, 3) − (0, 0, 0) = (4, 1, 3) m

Moment M = r × F

(r × F)x = ryFz − rzFy = 1·60 − 3·(−40) = 180 N·m
(r × F)y = rzFx − rxFz = 3·10 − 4·60 = −210 N·m
(r × F)z = rxFy − ryFx = 4·(−40) − 1·10 = −170 N·m

Requested component

My = −210 N·m

Answer

My = −210 N·m
3.Beam support reactions

Answer: RA = 34 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Replace each distributed load by its resultant (its area) acting at the centroid of the load diagram, and take moments about a support to remove that support’s reaction from the equation.

Resultant of the triangular load

W = ½·12·5 = 30 kN
x̄ = 2L/3 = 3.333 m

Equilibrium

Moments about A, counter-clockwise positive. Then vertical force balance.

ΣMA = 0: RB·5 = 30·3.333 + 80·3.5
RB = 76 kN
RA = 110 − 76 = 34 kN

Answer

RA = 34 kN
4.Beam support reactions

Answer: RA = 35.2 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Replace each distributed load by its resultant (its area) acting at the centroid of the load diagram, and take moments about a support to remove that support’s reaction from the equation.

Components of P

Pv = 30·sin 30° = 15 kN
Ph = 30·cos 30° = 25.98 kN

Reactions

ΣMA = 0: RB·8 = 15·6 + 40·4 → RB = 31.25 kN
Ay = 15 + 40 − 31.25 = 23.75 kN
Ax = Ph = 25.98 kN

Resultant at A

RA = √(25.98² + 23.75²) = 35.2 kN

Answer

RA = 35.2 kN
5.Truss: method of joints

Answer: FBC = −25.16 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB30 kNAy​Cy​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·4 = 30·3 → Cy = 22.5 kN
ΣFy = 0: Ay = 30 − 22.5 = 7.5 kN

Joint C

The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.

sin γ = 2/2.236 = 0.8944, cos γ = 1/2.236 = 0.4472
ΣFy = 0: Cy + FBC·sin γ = 0 → FBC = −22.5/0.8944 = −25.16 kN

Answer

FBC = −25.16 kN (compression)
6.Truss: method of joints

Answer: FAB = −39.06 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB60 kN15 kNAy​Cy​Ax​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·6 = 60·2 + 15·3 → Cy = 27.5 kN
ΣFy = 0: Ay = 60 − 27.5 = 32.5 kN
ΣFx = 0: Ax = −15 kN

Joint A

Assume every member is in tension (pulling away from the joint). Only AB has a vertical component at A.

sin α = 3/3.606 = 0.8321
ΣFy = 0: Ay + FAB·sin α = 0
FAB = −32.5/0.8321 = −39.06 kN

Answer

FAB = −39.06 kN (compression)
7.Frames & machines

Answer: A = 8.732 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Strut force

FCD = 4·3/(0.6839·1.6) = 10.97 kN

Components at A

Ax = FCD·cos α = 8 kN (towards the wall)
Ay = 4 − FCD·sin α = −3.5 kN

Magnitude

A = √(8² + −3.5²) = 8.732 kN

Answer

A = 8.732 kN

A negative Ay means the wall pulls the beam down at A.

8.Frames & machines

Answer: Ax = 1.32 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Direction of BC

BC = 6.353 m, cos = 0.8815, sin = 0.4722

Whole frame: moments about A

FBC·0.4722·8 = 5·1.44 + 10·3
FBC = 9.847 kN

Horizontal balance

Ax + 10 − 9.847·0.8815 = 0
Ax = −1.32 kN → |Ax| = 1.32 kN

Answer

Ax = 1.32 kN

The minus sign means Ax points to the left.

9.Shear force & bending moment

Answer: Mx = −12.5 kN·m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut. An applied couple makes the bending moment diagram jump by the size of the couple.

Support reactions

Moments about A, counter-clockwise positive: RB·L − M0 = 0. Vertical balance: RA + RB = 0.

RB = M0/L = 50/8 = 6.25 kN (upward)
RA = −RB = −6.25 kN (downward)

Cut just left of the couple

The left part contains only RA.

Mx = RA·a = −6.25·2 = −12.5 kN·m

Answer

Mx = −12.5 kN·m
10.Shear force & bending moment

Answer: E (x = 4 m)

Largest bending moment: M changes slope wherever the shear force changes, so its peaks sit where the shear force crosses zero: under a point load, inside a distributed load, or over a support of an overhang. At a fixed support of a cantilever the moment is largest at the wall. Compare the size of M at those places, sagging or hogging.

Support reactions

Take moments about one support, then use the vertical force balance.

R1 = 12.67 kN, R2 = 64.33 kN

Bending moment at every mark

Sum the moments of all forces on one side of the cut. Sagging is positive, hogging negative.

MA = 0, MB = −20, MC = −29.33, MD = −42.67, ME = −70 kN·m, MF = −35, MG = 0

Answer

Mark E: ME = −70 kN·m
11.Centroid & second moment of area

Answer: Sx = 403.4 × 10³ mm³

Second moment of area: for a rectangle about its own centroidal axis I = bh³/12, and about its base bh³/3 (parallel-axis theorem I = Ic + A·d²). A hole is handled by subtracting its I, as long as both parts share the same axis. The elastic section modulus is S = I/c, where c is the distance to the extreme fibre.

Outer rectangle minus the two side cut-outs

Both cut-outs together are (B − tw) wide and hw = H − 2tf high, and share the axis x.

hw = 200 − 2·12 = 176 mm
Ix = (B·H³ − (B − tw)·hw³)/12 = (160·200³ − 146·176³)/12
Ix = 4.034 × 10⁷ mm⁴

Section modulus

c = H/2 = 100 mm
Sx = I/c = 4.034 × 10⁷/100
Sx = 403367 mm³ = 403.4 × 10³ mm³

Answer

Sx = 403.4 × 10³ mm³
12.Centroid & second moment of area

Answer: Ix = 171.8 × 10⁶ mm⁴

Sections with holes: treat a hole as a negative area. The centroid is ȳ = (A₁y₁ − A₂y₂)/(A₁ − A₂), with A₁, y₁ for the full plate and A₂, y₂ for the hole. For the second moment of area about the centroidal axis, use the parallel-axis theorem for each part and subtract the hole: I = (Ic1 + A₁d₁²) − (Ic2 + A₂d₂²), where d is the distance from each part's own centroid to the axis through ȳ. A rectangle has Ic = bh³/12 and a circle Ic = πd⁴/64.

Centroid

ȳ = (36000·120 − 1600·96)/(36000 − 1600) = 121.1 mm

Full plate about ȳ

150·240³/12 + 36000·−1.116² = 172.8 × 10⁶ mm⁴

Hole about ȳ

80·20³/12 + 1600·−25.12² = 1.063 × 10⁶ mm⁴

Subtract

Ix = 171.8 × 10⁶ mm⁴

Answer

Ix = 171.8 × 10⁶ mm⁴

ExamProblems · examproblems.com/courses/statics