Statics: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Vectors: dot & cross product

Magnitude
|a| = √(ax² + ay² + az²)
Unit vector
û = a/|a|
Components from an angle
Fx = F·cos θ, Fy = F·sin θ
Dot product
a·b = axbx + ayby + azbz = |a||b|cos θ
Scalar projection of a onto b
a·b/|b|
Work
W = F·d
Cross product
a × b = (aybz − azby, azbx − axbz, axby − aybx)
Areas
parallelogram |a × b|, triangle ½|a × b|
Moment about O
MO = r × F, r = A − O
Volume of a parallelepiped
V = |a·(b × c)|

Method

  1. Write every vector in components; for a force given by a magnitude and an angle, use F·cos θ and F·sin θ.
  2. For lengths and directions use the magnitude √(x² + y² + z²) and the unit vector a/|a|.
  3. Use the dot product for angles, projections, perpendicularity and work: a·b = |a||b|cos θ.
  4. Use the cross product for perpendicular vectors, areas and moments: write the three components carefully, keeping the order a × b.

Beam support reactions

Equilibrium
ΣFx = 0, ΣFy = 0, ΣM = 0
Uniform load
resultant w·L at the middle of the load
Moment
M = F·d

Method

  1. Draw a free-body diagram and replace each support by its reactions.
  2. Replace every distributed load by a single force at its centroid.
  3. Take moments about one support to find the reaction at the other.
  4. Use ΣFy = 0 to find the remaining reaction, and check with a second moment equation.

Truss: method of joints

Method of joints
ΣFx = 0, ΣFy = 0 at each joint
Method of sections
ΣM = 0 about a cut point
Member force
positive = tension, negative = compression

Method

  1. Find the support reactions for the whole truss.
  2. Method of joints: start at a joint with at most two unknown member forces and use ΣFx = 0 and ΣFy = 0.
  3. Method of sections: cut through the member you need and take moments about a point where the other unknown members meet.
  4. Assume tension; a negative answer means compression.

Frames & machines

Equilibrium of each member
ΣFx = 0, ΣFy = 0, ΣM = 0
Two-force member
force along the line through its two pins
Pin force
equal and opposite on the two members it joins
Magnitude of a pin force
F = √(Fx² + Fy²)
Lever, pliers, bell crank
Fin·a = Fout·b
Toggle
Flink = F/(2 sin θ), Q = F/(2 tan θ)
Uniform load
resultant w·L at the middle of the load

Method

  1. Draw the whole structure and find the support reactions if there are no more than three unknowns.
  2. Spot the two-force members: loaded only at two pins, their force acts along the line between the pins.
  3. Take the frame apart and draw every member on its own, with equal and opposite pin forces where members meet.
  4. For each member, take moments about a pin with unknown forces, then use ΣFx = 0 and ΣFy = 0; combine components into a magnitude at the end.

Shear force & bending moment

Shear and moment
V = ΣF on one side, M = ΣF·d on one side
Bending stress
σ = M·y/I
Rectangle
I = bh³/12
Section modulus
W = I/ymax
Simply supported, uniform load
Mmax = wL²/8

Method

  1. Find the support reactions from equilibrium of the whole beam.
  2. Cut the beam at the section you need and keep one side.
  3. Shear force: sum of the vertical forces on that side. Bending moment: sum of their moments about the cut.
  4. For the maximum moment, find where the shear force is zero.

Centroid & second moment of area

Centroid
ȳ = ΣAiyi/ΣAi
Rectangle
I = bh³/12
Parallel-axis theorem
I = Ic + A·d²
Composite section
I = Σ(Ic,i + Aidi²)

2Practice problems

1.Vectors: dot & cross productMedium
xyzab

Find the scalar projection compb a of a = (−7, −2, −5) onto b = (3, −5, −2), that is, the component of a in the direction of b.

a = (−7, −2, −5)b = (3, −5, −2)
compb a =
2.Vectors: dot & cross productHard
xyzrFOA

A force F = (−10, 0, 10) N acts at point A(4, −4, −2). Coordinates are in metres. Find the z-component Mz of the moment of the force about point O(−2, 0, 3).

F = (−10, 0, 10) NA(4, −4, −2) mO(−2, 0, 3) m
Mz = N·m
3.Beam support reactionsMedium
P1​ = 60 kNP2​ = 40 kNABRA​RB​ = ?1.5 m2 m1.5 m

The simply supported beam has a pin at A and a roller at B. Find the vertical support reaction RB.

L = 5 mP1 = 60 kN at 1.5 mP2 = 40 kN at 3.5 m
RB = kN
4.Beam support reactionsHard
w = 3 kN/mP = 35 kNABRA​RB​ = ?6 m1 m2 m1 m

The simply supported beam has a pin at A and a roller at B. Find the vertical support reaction RB.

L = 10 mP = 35 kN at 6 mw = 3 kN/m from 7 to 9 m
RB = kN
5.Truss: method of jointsMedium
ABBCACACB60 kN5 m3 m3 m

Use the method of joints to find the force FAC in member AC. Give tension as positive and compression as negative.

span = 5 mheight = 3 mB is 3 m from Avertical load = 60 kN
FAC = kN
6.Truss: method of jointsHard
ABBCACACB15 kN5 kN5 m1 m2 m

Use the method of joints to find the force FBC in member BC. Give tension as positive and compression as negative.

span = 5 mheight = 2 mB is 1 m from Avertical load = 15 kNhorizontal load = 5 kN →
FBC = kN
7.Frames & machinesMedium
5 kN3 m1.2 m1.8 mABCDE

The A-frame shown stands on a pin at A and a roller at B, 3 m apart. The legs meet at the pin C, 3 m high, and the horizontal tie DE is 1.2 m above the ground. A load of 5 kN acts at C. Find the magnitude of the force C that the pin C exerts on leg BC.

P = 5 kNAB = 3 mheight of C = 3 mheight of DE = 1.2 m
C = kN
8.Frames & machinesHard
10 kN2 kN5 m1 mABC

A uniform horizontal boom AB of weight 2 kN is pinned to a wall at A and held by a cable from its end B to the point C on the wall, 1 m above A. A load of 10 kN hangs at B. Find the tension T in the cable.

W = 10 kNWb = 2 kNAB = 5 mAC = 1 m
T = kN
9.Shear force & bending momentMedium
60 kN15 kNABCDEFG2 m2 m2 m2 m2 m2 m

The marks A to G split the beam into six equal parts. At which mark is the bending moment largest in size, sagging or hogging? Click it in the diagram.

60 kN @ 4 m15 kN @ 8 m
  1. 1A (x = 0 m)
  2. 2B (x = 2 m)
  3. 3C (x = 4 m)
  4. 4D (x = 6 m)
  5. 5E (x = 8 m)
  6. 6F (x = 10 m)
  7. 7G (x = 12 m)
10.Shear force & bending momentHard
20 kN30 kNABCDEFG1 m1 m1 m1 m1 m1 m

The marks A to G split the beam into six equal parts. At which mark is the bending moment largest in size, sagging or hogging? Click it in the diagram.

20 kN @ 6 m30 kN @ 3 m
  1. 1A (x = 0 m)
  2. 2B (x = 1 m)
  3. 3C (x = 2 m)
  4. 4D (x = 3 m)
  5. 5E (x = 4 m)
  6. 6F (x = 5 m)
  7. 7G (x = 6 m)
11.Centroid & second moment of areaMedium
B = 140H = 250t = 6xdimensions in mm

A hollow rectangular (box) section has outer width B = 140 mm, outer height H = 250 mm and a uniform wall thickness t = 6 mm. Find its radius of gyration r about the horizontal centroidal axis.

B = 140 mmH = 250 mmt = 6 mm
r = mm
12.Centroid & second moment of areaHard
150 mm240 mm156 mm60 × 40xIx​ = ?

A 150 mm × 240 mm plate has a rectangular cut-out 60 mm wide and 40 mm high, centred on the vertical centre line with its centre 156 mm above the bottom. Find the second moment of area Ix about the horizontal axis through the centroid.

b = 150 mmh = 240 mmcut-out: 60 × 40 mmhole centre: y = 156 mm
Ix = × 10⁶ mm⁴

3Solutions

1.Vectors: dot & cross product

Answer: compb a = −0.1622

Dot product: a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.

Dot product

a·b = (−7)·3 + (−2)·(−5) + (−5)·(−2) = −1

Length of b

|b| = √(3² + (−5)² + (−2)²) = 6.164

Scalar projection

compb a = a·b/|b| = −1/6.164 = −0.1622

Answer

compb a = −0.1622

Negative: a has a component pointing against b.

2.Vectors: dot & cross product

Answer: Mz = −40 N·m

Cross product: a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.

Position vector from O to A

r = A − O = (4, −4, −2) − (−2, 0, 3) = (6, −4, −5) m

Moment M = r × F

(r × F)x = ryFz − rzFy = (−4)·10 − (−5)·0 = −40 N·m
(r × F)y = rzFx − rxFz = (−5)·(−10) − 6·10 = −10 N·m
(r × F)z = rxFy − ryFx = 6·0 − (−4)·(−10) = −40 N·m

Requested component

Mz = −40 N·m

Answer

Mz = −40 N·m
3.Beam support reactions

Answer: RB = 46 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.

P1​ = 60 kNP2​ = 40 kNABRA​RB​1.5 m2 m1.5 m

Free-body diagram

Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.

Equilibrium

Moments about A, counter-clockwise positive. Then vertical force balance.

ΣMA = 0: RB·5 = 60·1.5 + 40·3.5
RB = 230/5 = 46 kN
ΣFy = 0: RA = 100 − 46 = 54 kN

Answer

RB = 46 kN
4.Beam support reactions

Answer: RB = 25.8 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.

w = 3 kN/mP = 35 kNABRA​RB​6 m1 m2 m1 m

Free-body diagram

Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.

Equilibrium

Moments about A, counter-clockwise positive. Then vertical force balance.

UDL resultant: W = w·ℓ = 3·2 = 6 kN, acting at x̄ = 8 m
ΣMA = 0: RB·10 = 35·6 + 3·2·8
RB = 258/10 = 25.8 kN
ΣFy = 0: RA = 41 − 25.8 = 15.2 kN

Answer

RB = 25.8 kN
5.Truss: method of joints

Answer: FAC = 24 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB60 kNAy​Cy​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·5 = 60·3 → Cy = 36 kN
ΣFy = 0: Ay = 60 − 36 = 24 kN

Joint C

The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.

sin γ = 3/3.606 = 0.8321, cos γ = 2/3.606 = 0.5547
ΣFy = 0: Cy + FBC·sin γ = 0 → FBC = −36/0.8321 = −43.27 kN
ΣFx = 0: −FAC − FBC·cos γ = 0 → FAC = −(−43.27)·0.5547 = 24 kN

Answer

FAC = 24 kN (tension)
6.Truss: method of joints

Answer: FBC = −11.18 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB15 kN5 kNAy​Cy​Ax​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·5 = 15·1 + 5·2 → Cy = 5 kN
ΣFy = 0: Ay = 15 − 5 = 10 kN
ΣFx = 0: Ax = −5 kN

Joint C

The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.

sin γ = 2/4.472 = 0.4472, cos γ = 4/4.472 = 0.8944
ΣFy = 0: Cy + FBC·sin γ = 0 → FBC = −5/0.4472 = −11.18 kN

Answer

FBC = −11.18 kN (compression)
7.Frames & machines

Answer: C = 3.254 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Tie force from leg BC

By = 2.5 kN
T = 2.5·1.5/1.8 = 2.083 kN

Components of the pin force on BC

Cx = T = 2.083 kN, Cy = −By = −2.5 kN

Magnitude

C = √(2.083² + 2.5²) = 3.254 kN

Answer

C = 3.254 kN
8.Frames & machines

Answer: T = 56.09 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Cable angle

BC = √(5² + 1²) = 5.099 m, sin β = 0.1961

Moments about A

T·0.1961·5 = 10·5 + 2·2.5
T = 56.09 kN

Answer

T = 56.09 kN
9.Shear force & bending moment

Answer: C (x = 4 m)

Largest bending moment: M changes slope wherever the shear force changes, so its peaks sit where the shear force crosses zero: under a point load, inside a distributed load, or over a support of an overhang. At a fixed support of a cantilever the moment is largest at the wall. Compare the size of M at those places, sagging or hogging.

Support reactions

Take moments about one support, then use the vertical force balance.

R1 = 45 kN, R2 = 30 kN

Bending moment at every mark

Sum the moments of all forces on one side of the cut. Sagging is positive, hogging negative.

MA = 0, MB = 90, MC = 180 kN·m, MD = 150, ME = 120, MF = 60, MG = 0

Answer

Mark C: MC = 180 kN·m
10.Shear force & bending moment

Answer: D (x = 3 m)

Largest bending moment: M changes slope wherever the shear force changes, so its peaks sit where the shear force crosses zero: under a point load, inside a distributed load, or over a support of an overhang. At a fixed support of a cantilever the moment is largest at the wall. Compare the size of M at those places, sagging or hogging.

Support reactions

Take moments about one support, then use the vertical force balance.

R1 = 8 kN, R2 = 42 kN

Bending moment at every mark

Sum the moments of all forces on one side of the cut. Sagging is positive, hogging negative.

MA = 0, MB = 8, MC = 16, MD = 24 kN·m, ME = 2, MF = −20, MG = 0

Answer

Mark D: MD = 24 kN·m
11.Centroid & second moment of area

Answer: r = 92.12 mm

Second moment of area: for a rectangle about its own centroidal axis I = bh³/12, and about its base bh³/3 (parallel-axis theorem I = Ic + A·d²). A hole is handled by subtracting its I, as long as both parts share the same axis. The elastic section modulus is S = I/c, where c is the distance to the extreme fibre. The radius of gyration r = √(I/A) is the distance at which the whole area would give the same I; it is used in column buckling.

Net area and second moment of area

b = 128 mm, h = 238 mm
A = BH − bh = 140·250 − 128·238 = 4536 mm²
I = (BH³ − bh³)/12 = 3.849 × 10⁷ mm⁴

Radius of gyration

r = √(I/A) = √(3.849 × 10⁷/4536) = 92.12 mm

Answer

r = 92.12 mm
12.Centroid & second moment of area

Answer: Ix = 169.1 × 10⁶ mm⁴

Sections with holes: treat a hole as a negative area. The centroid is ȳ = (A₁y₁ − A₂y₂)/(A₁ − A₂), with A₁, y₁ for the full plate and A₂, y₂ for the hole. For the second moment of area about the centroidal axis, use the parallel-axis theorem for each part and subtract the hole: I = (Ic1 + A₁d₁²) − (Ic2 + A₂d₂²), where d is the distance from each part's own centroid to the axis through ȳ. A rectangle has Ic = bh³/12 and a circle Ic = πd⁴/64.

Centroid

ȳ = (36000·120 − 2400·156)/(36000 − 2400) = 117.4 mm

Full plate about ȳ

150·240³/12 + 36000·2.571² = 173 × 10⁶ mm⁴

Hole about ȳ

60·40³/12 + 2400·38.57² = 3.891 × 10⁶ mm⁴

Subtract

Ix = 169.1 × 10⁶ mm⁴

Answer

Ix = 169.1 × 10⁶ mm⁴

ExamProblems · examproblems.com/courses/statics