Statics: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Vectors: dot & cross product

Magnitude
|a| = √(ax² + ay² + az²)
Unit vector
û = a/|a|
Components from an angle
Fx = F·cos θ, Fy = F·sin θ
Dot product
a·b = axbx + ayby + azbz = |a||b|cos θ
Scalar projection of a onto b
a·b/|b|
Work
W = F·d
Cross product
a × b = (aybz − azby, azbx − axbz, axby − aybx)
Areas
parallelogram |a × b|, triangle ½|a × b|
Moment about O
MO = r × F, r = A − O
Volume of a parallelepiped
V = |a·(b × c)|

Method

  1. Write every vector in components; for a force given by a magnitude and an angle, use F·cos θ and F·sin θ.
  2. For lengths and directions use the magnitude √(x² + y² + z²) and the unit vector a/|a|.
  3. Use the dot product for angles, projections, perpendicularity and work: a·b = |a||b|cos θ.
  4. Use the cross product for perpendicular vectors, areas and moments: write the three components carefully, keeping the order a × b.

Beam support reactions

Equilibrium
ΣFx = 0, ΣFy = 0, ΣM = 0
Uniform load
resultant w·L at the middle of the load
Moment
M = F·d

Method

  1. Draw a free-body diagram and replace each support by its reactions.
  2. Replace every distributed load by a single force at its centroid.
  3. Take moments about one support to find the reaction at the other.
  4. Use ΣFy = 0 to find the remaining reaction, and check with a second moment equation.

Truss: method of joints

Method of joints
ΣFx = 0, ΣFy = 0 at each joint
Method of sections
ΣM = 0 about a cut point
Member force
positive = tension, negative = compression

Method

  1. Find the support reactions for the whole truss.
  2. Method of joints: start at a joint with at most two unknown member forces and use ΣFx = 0 and ΣFy = 0.
  3. Method of sections: cut through the member you need and take moments about a point where the other unknown members meet.
  4. Assume tension; a negative answer means compression.

Frames & machines

Equilibrium of each member
ΣFx = 0, ΣFy = 0, ΣM = 0
Two-force member
force along the line through its two pins
Pin force
equal and opposite on the two members it joins
Magnitude of a pin force
F = √(Fx² + Fy²)
Lever, pliers, bell crank
Fin·a = Fout·b
Toggle
Flink = F/(2 sin θ), Q = F/(2 tan θ)
Uniform load
resultant w·L at the middle of the load

Method

  1. Draw the whole structure and find the support reactions if there are no more than three unknowns.
  2. Spot the two-force members: loaded only at two pins, their force acts along the line between the pins.
  3. Take the frame apart and draw every member on its own, with equal and opposite pin forces where members meet.
  4. For each member, take moments about a pin with unknown forces, then use ΣFx = 0 and ΣFy = 0; combine components into a magnitude at the end.

Shear force & bending moment

Shear and moment
V = ΣF on one side, M = ΣF·d on one side
Bending stress
σ = M·y/I
Rectangle
I = bh³/12
Section modulus
W = I/ymax
Simply supported, uniform load
Mmax = wL²/8

Method

  1. Find the support reactions from equilibrium of the whole beam.
  2. Cut the beam at the section you need and keep one side.
  3. Shear force: sum of the vertical forces on that side. Bending moment: sum of their moments about the cut.
  4. For the maximum moment, find where the shear force is zero.

Centroid & second moment of area

Centroid
ȳ = ΣAiyi/ΣAi
Rectangle
I = bh³/12
Parallel-axis theorem
I = Ic + A·d²
Composite section
I = Σ(Ic,i + Aidi²)

2Practice problems

1.Vectors: dot & cross productMedium
xyzab

Find the value of k for which the vectors a = (−6, 3, 3) and b = (−6, −3, k) are perpendicular.

a = (−6, 3, 3)b = (−6, −3, k)
k =
2.Vectors: dot & cross productHard
xyzabc

Find the volume V of the parallelepiped whose edges from one corner are a = (−5, −2, 5), b = (1, −5, −5) and c = (−4, 2, 0).

a = (−5, −2, 5)b = (1, −5, −5)c = (−4, 2, 0)
V =
3.Beam support reactionsMedium
w0​ = 10 kN/mP = 50 kNABRA​ = ?3 m2 m

The simply supported beam (pin at A, roller at B) carries a linearly varying load that falls from 10 kN/m at A to zero at B. A point load P also acts at 3 m from A. Find the vertical support reaction RA.

L = 5 mw0 = 10 kN/mP = 50 kN at 3 m
RA = kN
4.Beam support reactionsHard
w0​ = 6 kN/mP = 65 kNABMA​ = ?3 m2 m

The cantilever beam is fixed to the wall at A. It carries a linearly varying load that is zero at the wall and rises to 6 kN/m at the free end B, plus a point load P at 3 m from the wall. Find the magnitude of the reaction moment MA at the wall.

L = 5 mw0 = 6 kN/mP = 65 kN at 3 m
MA = kN·m
5.Truss: method of jointsMedium
ABCDEFGH15 kN30 kN35 kN4 × 4 m3 m

Exactly one member of this truss carries no force under these loads. Which is the zero-force member? Click it in the diagram.

B: 15 kN ↓D: 30 kN ↓G: 35 kN ↓
  1. 1member AB
  2. 2member BC
  3. 3member CD
  4. 4member DE
  5. 5member FG
  6. 6member GH
  7. 7member AF
  8. 8member HE
  9. 9member BF
  10. 10member CG
  11. 11member DH
  12. 12member BG
  13. 13member DG
6.Truss: method of jointsHard
ABCDEFGH40 kN20 kN10 kN20 kN4 × 4 m4 m

Exactly one member of this truss carries no force under these loads. Which is the zero-force member? Click it in the diagram.

B: 40 kN ↓F: 20 kN →G: 10 kN ↓H: 20 kN ↓
  1. 1member AB
  2. 2member BC
  3. 3member CD
  4. 4member DE
  5. 5member FG
  6. 6member GH
  7. 7member AF
  8. 8member HE
  9. 9member BF
  10. 10member CG
  11. 11member DH
  12. 12member BG
  13. 13member DG
7.Frames & machinesMedium
4 kN3 m1.2 m0.8 mABCDE

The A-frame shown stands on a pin at A and a roller at B, 3 m apart. The legs meet at the pin C, 2 m high, and the horizontal tie DE is 1.2 m above the ground. A load of 4 kN acts at C. Find the magnitude of the force C that the pin C exerts on leg BC.

P = 4 kNAB = 3 mheight of C = 2 mheight of DE = 1.2 m
C = kN
8.Frames & machinesHard
w = 4 kN/m4 kN0.6 m0.9 m1 mABCD

The beam AB of the wall bracket shown is pinned at A and propped by the strut CD (C is 1 m below A). The beam carries a uniform load of 4 kN/m over its full length and a point load of 4 kN at its free end B. Find the force FCD in the strut.

w = 4 kN/mP = 4 kNAD = 0.6 mAB = 1.5 mAC = 1 m
FCD = kN
9.Shear force & bending momentMedium
M0​ = 55 kN·mAB1.5 m4.5 m

The simply supported beam carries a clockwise couple M0 = 55 kN·m at x = 1.5 m from A, and no other load. Find the bending moment Mx just to the left of the couple. Use sagging moments positive and upward shear on the left face positive.

L = 6 mM0 = 55 kN·m clockwise, at 1.5 m
Mx = kN·m
10.Shear force & bending momentHard
w = 5 kN/mP = 20 kNABsection1.5 m2.5 m

Find the bending moment Mx at the section x = 1.5 m from support A. Use sagging moments positive and upward shear on the left face positive.

L = 4 mP = 20 kN at 1.5 mw = 5 kN/m from 0 to 4 mx = 1.5 m
Mx = kN·m
11.Centroid & second moment of areaMedium
100 mm300 mm195 mmØ50xIx​ = ?

A 100 mm × 300 mm plate has a circular hole of diameter 50 mm on its vertical centre line, with its centre 195 mm above the bottom. Find the second moment of area Ix about the horizontal axis through the centroid.

b = 100 mmh = 300 mmd = 50 mmhole centre: y = 195 mm
Ix = × 10⁶ mm⁴
12.Centroid & second moment of areaHard
130340186xM = 50 kN·mdimensions in mm

A symmetric I-section has flanges 130 mm wide and 18 mm thick, an overall depth of 340 mm and a web 6 mm thick. It carries a bending moment of 50 kN·m about the axis x. Find the size of the bending stress σj at the junction of the web and the top flange.

B = 130 mmH = 340 mmtf = 18 mmtw = 6 mmM = 50 kN·m
σj = MPa

3Solutions

1.Vectors: dot & cross product

Answer: k = −9

Dot product: a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.

Dot product equals zero

a·b = (−6)·(−6) + 3·(−3) + 3·k = 0
27 + 3·k = 0

Solve for k

k = −27/3 = −9

Answer

k = −9
2.Vectors: dot & cross product

Answer: V = 180

Cross product: a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.

Cross product b × c

(b × c)x = bycz − bzcy = (−5)·0 − (−5)·2 = 10
(b × c)y = bzcx − bxcz = (−5)·(−4) − 1·0 = 20
(b × c)z = bxcy − bycx = 1·2 − (−5)·(−4) = −18

Dot product with a

a·(b × c) = (−5)·10 + (−2)·20 + 5·(−18) = −180
V = |−180| = 180

Answer

V = 180
3.Beam support reactions

Answer: RA = 36.67 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Replace each distributed load by its resultant (its area) acting at the centroid of the load diagram, and take moments about a support to remove that support’s reaction from the equation.

Resultant of the triangular load

W = ½·10·5 = 25 kN
x̄ = L/3 = 1.667 m

Equilibrium

Moments about A, counter-clockwise positive. Then vertical force balance.

ΣMA = 0: RB·5 = 25·1.667 + 50·3
RB = 38.33 kN
RA = 75 − 38.33 = 36.67 kN

Answer

RA = 36.67 kN
4.Beam support reactions

Answer: MA = 245 kN·m

Cantilever equilibrium: a fixed support can push up and also resist rotation, so it gives a vertical reaction RA and a reaction moment MA. ΣFy = 0 gives RA, and moments about the wall give MA = Σ(load × distance from the wall). A distributed load acts as its resultant at the centroid of the load diagram.

Resultant of the triangular load

W = ½·6·5 = 15 kN
x̄ = 2L/3 = 3.333 m

Moment about the wall

MA = W·x̄ + P·a = 15·3.333 + 65·3 = 245 kN·m

Answer

MA = 245 kN·m
5.Truss: method of joints

Answer: member CG

Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.

Joint C

BC and CD lie on one straight line and the joint carries no load. Balancing forces across that line leaves only CG.

ΣF⊥ = 0 → FCG = 0

Check with the method of joints

Solving all joints gives these member forces (T = tension, C = compression).

AB: 48.33 kN (T), BC: 76.67 kN (T), CD: 76.67 kN (T), DE: 58.33 kN (T), FG: 48.33 kN (C), GH: 58.33 kN (C), AF: 60.42 kN (C), HE: 72.92 kN (C), BF: 36.25 kN (T), CG: 0, DH: 43.75 kN (T), BG: 35.42 kN (C), DG: 22.92 kN (C)

Answer

Zero-force member: CG
6.Truss: method of joints

Answer: member CG

Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.

Joint C

BC and CD lie on one straight line and the joint carries no load. Balancing forces across that line leaves only CG.

ΣF⊥ = 0 → FCG = 0

Check with the method of joints

Solving all joints gives these member forces (T = tension, C = compression).

AB: 55 kN (T), BC: 50 kN (T), CD: 50 kN (T), DE: 35 kN (T), FG: 55 kN (C), GH: 35 kN (C), AF: 49.5 kN (C), HE: 49.5 kN (C), BF: 35 kN (T), CG: 0, DH: 15 kN (T), BG: 7.071 kN (T), DG: 21.21 kN (C)

Answer

Zero-force member: CG
7.Frames & machines

Answer: C = 4.25 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Tie force from leg BC

By = 2 kN
T = 2·1.5/0.8 = 3.75 kN

Components of the pin force on BC

Cx = T = 3.75 kN, Cy = −By = −2 kN

Magnitude

C = √(3.75² + 2²) = 4.25 kN

Answer

C = 4.25 kN
8.Frames & machines

Answer: FCD = 20.41 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Resultant of the uniform load

w·L = 4·1.5 = 6 kN at 0.75 m

Moments about A for the beam

FCD·0.8575·0.6 = 6·0.75 + 4·1.5 = 10.5 kN·m
FCD = 20.41 kN

Answer

FCD = 20.41 kN
9.Shear force & bending moment

Answer: Mx = −13.75 kN·m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut. An applied couple makes the bending moment diagram jump by the size of the couple.

Support reactions

Moments about A, counter-clockwise positive: RB·L − M0 = 0. Vertical balance: RA + RB = 0.

RB = M0/L = 55/6 = 9.167 kN (upward)
RA = −RB = −9.167 kN (downward)

Cut just left of the couple

The left part contains only RA.

Mx = RA·a = −9.167·1.5 = −13.75 kN·m

Answer

Mx = −13.75 kN·m
10.Shear force & bending moment

Answer: Mx = 28.13 kN·m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.

Support reactions

Equilibrium of the whole beam.

UDL resultant: W = w·ℓ = 5·4 = 20 kN, acting at x̄ = 2 m
ΣMA = 0: RB·4 = 20·1.5 + 5·4·2
RB = 70/4 = 17.5 kN
ΣFy = 0: RA = 40 − 17.5 = 22.5 kN
w = 5 kN/mP = 20 kNABRA​ = 22.5RB​ = 17.5section1.5 m2.5 m

Cut at x = 1.5 m and keep the left part

Only forces left of the cut appear. A UDL portion acts as one force at the middle of that portion.

M = RA·x − (each load left of the cut × its distance to the cut)
Mx = 22.5·1.5 − 5·1.5·0.75 = 28.13 kN·m

Answer

Mx = 28.13 kN·m
11.Centroid & second moment of area

Answer: Ix = 220.4 × 10⁶ mm⁴

Sections with holes: treat a hole as a negative area. The centroid is ȳ = (A₁y₁ − A₂y₂)/(A₁ − A₂), with A₁, y₁ for the full plate and A₂, y₂ for the hole. For the second moment of area about the centroidal axis, use the parallel-axis theorem for each part and subtract the hole: I = (Ic1 + A₁d₁²) − (Ic2 + A₂d₂²), where d is the distance from each part's own centroid to the axis through ȳ. A rectangle has Ic = bh³/12 and a circle Ic = πd⁴/64.

Centroid

ȳ = (30000·150 − 1963·195)/(30000 − 1963) = 146.8 mm

Full plate about ȳ

100·300³/12 + 30000·3.152² = 225.3 × 10⁶ mm⁴

Hole about ȳ

π·50⁴/64 + 1963·48.15² = 4.859 × 10⁶ mm⁴

Subtract

Ix = 220.4 × 10⁶ mm⁴

Answer

Ix = 220.4 × 10⁶ mm⁴
12.Centroid & second moment of area

Answer: σj = 56.1 MPa

Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.

Outer rectangle minus the two side cut-outs

Both cut-outs together are (B − tw) wide and hw = H − 2tf high, and share the axis x.

hw = 340 − 2·18 = 304 mm
Ix = (B·H³ − (B − tw)·hw³)/12 = (130·340³ − 124·304³)/12
Ix = 1.355 × 10⁸ mm⁴

Bending stress

y = 170 − 18 = 152 mm
σ = M·y/I = 5 × 10⁷·152/1.355 × 10⁸ = 56.1 MPa

Answer

σj = 56.1 MPa

ExamProblems · examproblems.com/courses/statics