Statics: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Vectors: dot & cross product

Magnitude
|a| = √(ax² + ay² + az²)
Unit vector
û = a/|a|
Components from an angle
Fx = F·cos θ, Fy = F·sin θ
Dot product
a·b = axbx + ayby + azbz = |a||b|cos θ
Scalar projection of a onto b
a·b/|b|
Work
W = F·d
Cross product
a × b = (aybz − azby, azbx − axbz, axby − aybx)
Areas
parallelogram |a × b|, triangle ½|a × b|
Moment about O
MO = r × F, r = A − O
Volume of a parallelepiped
V = |a·(b × c)|

Method

  1. Write every vector in components; for a force given by a magnitude and an angle, use F·cos θ and F·sin θ.
  2. For lengths and directions use the magnitude √(x² + y² + z²) and the unit vector a/|a|.
  3. Use the dot product for angles, projections, perpendicularity and work: a·b = |a||b|cos θ.
  4. Use the cross product for perpendicular vectors, areas and moments: write the three components carefully, keeping the order a × b.

Beam support reactions

Equilibrium
ΣFx = 0, ΣFy = 0, ΣM = 0
Uniform load
resultant w·L at the middle of the load
Moment
M = F·d

Method

  1. Draw a free-body diagram and replace each support by its reactions.
  2. Replace every distributed load by a single force at its centroid.
  3. Take moments about one support to find the reaction at the other.
  4. Use ΣFy = 0 to find the remaining reaction, and check with a second moment equation.

Truss: method of joints

Method of joints
ΣFx = 0, ΣFy = 0 at each joint
Method of sections
ΣM = 0 about a cut point
Member force
positive = tension, negative = compression

Method

  1. Find the support reactions for the whole truss.
  2. Method of joints: start at a joint with at most two unknown member forces and use ΣFx = 0 and ΣFy = 0.
  3. Method of sections: cut through the member you need and take moments about a point where the other unknown members meet.
  4. Assume tension; a negative answer means compression.

Frames & machines

Equilibrium of each member
ΣFx = 0, ΣFy = 0, ΣM = 0
Two-force member
force along the line through its two pins
Pin force
equal and opposite on the two members it joins
Magnitude of a pin force
F = √(Fx² + Fy²)
Lever, pliers, bell crank
Fin·a = Fout·b
Toggle
Flink = F/(2 sin θ), Q = F/(2 tan θ)
Uniform load
resultant w·L at the middle of the load

Method

  1. Draw the whole structure and find the support reactions if there are no more than three unknowns.
  2. Spot the two-force members: loaded only at two pins, their force acts along the line between the pins.
  3. Take the frame apart and draw every member on its own, with equal and opposite pin forces where members meet.
  4. For each member, take moments about a pin with unknown forces, then use ΣFx = 0 and ΣFy = 0; combine components into a magnitude at the end.

Shear force & bending moment

Shear and moment
V = ΣF on one side, M = ΣF·d on one side
Bending stress
σ = M·y/I
Rectangle
I = bh³/12
Section modulus
W = I/ymax
Simply supported, uniform load
Mmax = wL²/8

Method

  1. Find the support reactions from equilibrium of the whole beam.
  2. Cut the beam at the section you need and keep one side.
  3. Shear force: sum of the vertical forces on that side. Bending moment: sum of their moments about the cut.
  4. For the maximum moment, find where the shear force is zero.

Centroid & second moment of area

Centroid
ȳ = ΣAiyi/ΣAi
Rectangle
I = bh³/12
Parallel-axis theorem
I = Ic + A·d²
Composite section
I = Σ(Ic,i + Aidi²)

2Practice problems

1.Vectors: dot & cross productMedium
xyzab

Find the value of k for which the vectors a = (0, −2, 2) and b = (1, k, −4) are perpendicular.

a = (0, −2, 2)b = (1, k, −4)
k =
2.Vectors: dot & cross productHard
xyzab

The unit vector n̂ is perpendicular to both a = (1, −5, 4) and b = (4, 1, 3) and has a positive z-component. Find its y-component n̂y.

a = (1, −5, 4)b = (4, 1, 3)n̂z > 0
n̂y =
3.Beam support reactionsMedium
P = 70 kNM = 15 kN·mABRB​ = ?4 m1 m3 m

The simply supported beam has a pin at A and a roller at B. It carries a point load P at 5 m from A and a clockwise couple M at 4 m from A. Find the vertical reaction RB, taking upward as positive.

L = 8 mP = 70 kN at 5 mM = 15 kN·m (clockwise) at 4 m
RB = kN
4.Beam support reactionsHard
w = 3 kN/mP = 55 kNABCRB​ = ?1 m2 m1.5 m1.5 m

The beam has a pin at A and a roller at B, 4.5 m from A, and overhangs B to the free end C. It carries a point load P at 1 m from A and a uniformly distributed load w from 3 m to the free end at 6 m. Find the vertical reaction RB, taking upward as positive.

AB = 4.5 mAC = 6 mP = 55 kN at 1 mw = 3 kN/m from 3 to 6 m
RB = kN
5.Truss: method of jointsMedium
ABBCACACB35 kN5 m1 m2 m

Use the method of joints to find the force FBC in member BC. Give tension as positive and compression as negative.

span = 5 mheight = 2 mB is 1 m from Avertical load = 35 kN
FBC = kN
6.Truss: method of jointsHard
ABBCACACB25 kN5 kN4 m1 m3 m

Use the method of joints to find the force FAC in member AC. Give tension as positive and compression as negative.

span = 4 mheight = 3 mB is 1 m from Avertical load = 25 kNhorizontal load = 5 kN →
FAC = kN
7.Frames & machinesMedium
100 NQ = ?25°ABC

In the toggle clamp shown, two equal links AB and BC are pinned together at B, and each makes 25° with the line AC. A downward force of 100 N is applied at B. The slider C presses on a workpiece. Neglecting friction and weights, find the horizontal clamping force Q.

F = 100 Nθ = 25°
Q = N
8.Frames & machinesHard
F = ?1500 N30 mmABC

A toggle press has two equal links AB and BC, each 80 mm long between pins. The joint B sits 30 mm above the line AC. Which downward force F at B produces a horizontal pressing force of 1500 N at the slider C? Neglect friction and weights.

Q = 1500 NAB = BC = 80 mmh = 30 mm
F = N
9.Shear force & bending momentMedium
w = 3 kN/mABsection2.5 m3.5 m

Find the shear force Vx at the section x = 2.5 m from support A. Use sagging moments positive and upward shear on the left face positive.

L = 6 mw = 3 kN/m from 0 to 6 mx = 2.5 m
Vx = kN
10.Shear force & bending momentHard
w = 12 kN/mP = 20 kNABsection3 m0.5 m0.5 m

Find the bending moment Mx at the section x = 3.5 m from support A. Use sagging moments positive and upward shear on the left face positive.

L = 4 mP = 20 kN at 3 mw = 12 kN/m from 0 to 4 mx = 3.5 m
Mx = kN·m
11.Centroid & second moment of areaMedium
xD = 150d = 142dimensions in mm

A circular tube has outside diameter D = 150 mm and inside diameter d = 142 mm. Find its radius of gyration r about the horizontal centroidal axis.

D = 150 mmd = 142 mm
r = mm
12.Centroid & second moment of areaHard
160460246xM = 100 kN·mdimensions in mm

A symmetric I-section has flanges 160 mm wide and 24 mm thick, an overall depth of 460 mm and a web 6 mm thick. It carries a bending moment of 100 kN·m about the axis x. Find the size of the bending stress σj at the junction of the web and the top flange.

B = 160 mmH = 460 mmtf = 24 mmtw = 6 mmM = 100 kN·m
σj = MPa

3Solutions

1.Vectors: dot & cross product

Answer: k = −4

Dot product: a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.

Dot product equals zero

a·b = 0·1 + (−2)·k + 2·(−4) = 0
−8 + (−2)·k = 0

Solve for k

k = −(−8)/(−2) = −4

Answer

k = −4
2.Vectors: dot & cross product

Answer: n̂y = 0.4172

Cross product: a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.

Cross product

(a × b)x = aybz − azby = (−5)·3 − 4·1 = −19
(a × b)y = azbx − axbz = 4·4 − 1·3 = 13
(a × b)z = axby − aybx = 1·1 − (−5)·4 = 21

Normalise

The z-component of a × b is already positive.

|a × b| = √((−19)² + 13² + 21²) = 31.16
n̂ = (−19, 13, 21)/31.16 = (−0.6097, 0.4172, 0.6739)
n̂y = 0.4172

Answer

n̂y = 0.4172
3.Beam support reactions

Answer: RB = 45.63 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Replace each distributed load by its resultant (its area) acting at the centroid of the load diagram, and take moments about a support to remove that support’s reaction from the equation.

Moments about A

Counter-clockwise positive.

ΣMA = 0: RB·8 − 70·5 − 15 = 0
RB = 365/8 = 45.63 kN

Vertical equilibrium

RA = 70 − 45.63 = 24.38 kN

Answer

RB = 45.63 kN

A negative reaction acts downward.

4.Beam support reactions

Answer: RB = 21.22 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Replace each distributed load by its resultant (its area) acting at the centroid of the load diagram, and take moments about a support to remove that support’s reaction from the equation.

Resultant of the distributed load

W = 3·3 = 9 kN, x̄ = (3 + 6)/2 = 4.5 m

Equilibrium

Moments about A, counter-clockwise positive. Then vertical force balance.

ΣMA = 0: RB·4.5 = 55·1 + 9·4.5
RB = 95.5/4.5 = 21.22 kN
RA = 64 − 21.22 = 42.78 kN

Answer

RB = 21.22 kN
5.Truss: method of joints

Answer: FBC = −15.65 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB35 kNAy​Cy​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·5 = 35·1 → Cy = 7 kN
ΣFy = 0: Ay = 35 − 7 = 28 kN

Joint C

The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.

sin γ = 2/4.472 = 0.4472, cos γ = 4/4.472 = 0.8944
ΣFy = 0: Cy + FBC·sin γ = 0 → FBC = −7/0.4472 = −15.65 kN

Answer

FBC = −15.65 kN (compression)
6.Truss: method of joints

Answer: FAC = 10 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB25 kN5 kNAy​Cy​Ax​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·4 = 25·1 + 5·3 → Cy = 10 kN
ΣFy = 0: Ay = 25 − 10 = 15 kN
ΣFx = 0: Ax = −5 kN

Joint C

The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.

sin γ = 3/4.243 = 0.7071, cos γ = 3/4.243 = 0.7071
ΣFy = 0: Cy + FBC·sin γ = 0 → FBC = −10/0.7071 = −14.14 kN
ΣFx = 0: −FAC − FBC·cos γ = 0 → FAC = −(−14.14)·0.7071 = 10 kN

Answer

FAC = 10 kN (tension)
7.Frames & machines

Answer: Q = 107.2 N

Machines: pliers, levers, linkages and clamps turn an input force into a larger or a differently directed output force. Draw one part as a free body and take moments about its pivot: the pin force drops out, and Fin·a = Fout·b gives the mechanical advantage a/b. The pin force then follows from ΣF = 0 on the same part. In a toggle, two links meet at a shallow angle θ; each link is a two-force member, so a small force F at the joint creates large link forces F/(2 sin θ) and a clamping force F/(2 tan θ).

Equilibrium of pin B

2·Flink·sin 25° = 100
Flink = 118.3 N

Clamping force

Q = Flink·cos 25° = 100/(2·tan 25°) = 107.2 N

Answer

Q = 107.2 N

The force ratio Q/F = 1.072 grows without limit as the links straighten.

8.Frames & machines

Answer: F = 1214 N

Machines: pliers, levers, linkages and clamps turn an input force into a larger or a differently directed output force. Draw one part as a free body and take moments about its pivot: the pin force drops out, and Fin·a = Fout·b gives the mechanical advantage a/b. The pin force then follows from ΣF = 0 on the same part. In a toggle, two links meet at a shallow angle θ; each link is a two-force member, so a small force F at the joint creates large link forces F/(2 sin θ) and a clamping force F/(2 tan θ).

Link angle

sin θ = 30/80 = 0.375, θ = 22.02°

Link force

Flink = Q/cos θ = 1618 N

Force at B

F = 2·Flink·sin θ = 2·1500·tan θ = 1214 N

Answer

F = 1214 N
9.Shear force & bending moment

Answer: Vx = 1.5 kN

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.

Support reactions

Equilibrium of the whole beam.

UDL resultant: W = w·ℓ = 3·6 = 18 kN, acting at x̄ = 3 m
ΣMA = 0: RB·6 = 3·6·3
RB = 54/6 = 9 kN
ΣFy = 0: RA = 18 − 9 = 9 kN
w = 3 kN/mABRA​ = 9RB​ = 9section2.5 m3.5 m

Cut at x = 2.5 m and keep the left part

Only forces left of the cut appear. A UDL portion acts as one force at the middle of that portion.

V = RA − (all downward loads left of the cut)
Vx = 9 − 3·2.5 = 1.5 kN

Answer

Vx = 1.5 kN
10.Shear force & bending moment

Answer: Mx = 18 kN·m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.

Support reactions

Equilibrium of the whole beam.

UDL resultant: W = w·ℓ = 12·4 = 48 kN, acting at x̄ = 2 m
ΣMA = 0: RB·4 = 20·3 + 12·4·2
RB = 156/4 = 39 kN
ΣFy = 0: RA = 68 − 39 = 29 kN
w = 12 kN/mP = 20 kNABRA​ = 29RB​ = 39section3 m0.5 m0.5 m

Cut at x = 3.5 m and keep the left part

Only forces left of the cut appear. A UDL portion acts as one force at the middle of that portion.

M = RA·x − (each load left of the cut × its distance to the cut)
Mx = 29·3.5 − 20·(3.5 − 3) − 12·3.5·1.75 = 18 kN·m

Answer

Mx = 18 kN·m
11.Centroid & second moment of area

Answer: r = 51.64 mm

Second moment of area: for a rectangle about its own centroidal axis I = bh³/12, and about its base bh³/3 (parallel-axis theorem I = Ic + A·d²). A hole is handled by subtracting its I, as long as both parts share the same axis. The elastic section modulus is S = I/c, where c is the distance to the extreme fibre. The radius of gyration r = √(I/A) is the distance at which the whole area would give the same I; it is used in column buckling.

Net area and second moment of area

A = π(D² − d²)/4 = 1835 mm²
I = π(D⁴ − d⁴)/64 = 4.892 × 10⁶ mm⁴

Radius of gyration

r = √(I/A) = √(4.892 × 10⁶/1835) = 51.64 mm

Answer

r = 51.64 mm
12.Centroid & second moment of area

Answer: σj = 51.46 MPa

Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.

Outer rectangle minus the two side cut-outs

Both cut-outs together are (B − tw) wide and hw = H − 2tf high, and share the axis x.

hw = 460 − 2·24 = 412 mm
Ix = (B·H³ − (B − tw)·hw³)/12 = (160·460³ − 154·412³)/12
Ix = 4.003 × 10⁸ mm⁴

Bending stress

y = 230 − 24 = 206 mm
σ = M·y/I = 1 × 10⁸·206/4.003 × 10⁸ = 51.46 MPa

Answer

σj = 51.46 MPa

ExamProblems · examproblems.com/courses/statics