In the print window, choose “Save as PDF” to keep a copy on your device.
1Formulas and methods
Vectors: dot & cross product
Magnitude
|a| = √(ax² + ay² + az²)
Unit vector
û = a/|a|
Components from an angle
Fx = F·cos θ, Fy = F·sin θ
Dot product
a·b = axbx + ayby + azbz = |a||b|cos θ
Scalar projection of a onto b
a·b/|b|
Work
W = F·d
Cross product
a × b = (aybz − azby, azbx − axbz, axby − aybx)
Areas
parallelogram |a × b|, triangle ½|a × b|
Moment about O
MO = r × F, r = A − O
Volume of a parallelepiped
V = |a·(b × c)|
Method
Write every vector in components; for a force given by a magnitude and an angle, use F·cos θ and F·sin θ.
For lengths and directions use the magnitude √(x² + y² + z²) and the unit vector a/|a|.
Use the dot product for angles, projections, perpendicularity and work: a·b = |a||b|cos θ.
Use the cross product for perpendicular vectors, areas and moments: write the three components carefully, keeping the order a × b.
Beam support reactions
Equilibrium
ΣFx = 0, ΣFy = 0, ΣM = 0
Uniform load
resultant w·L at the middle of the load
Moment
M = F·d
Method
Draw a free-body diagram and replace each support by its reactions.
Replace every distributed load by a single force at its centroid.
Take moments about one support to find the reaction at the other.
Use ΣFy = 0 to find the remaining reaction, and check with a second moment equation.
Truss: method of joints
Method of joints
ΣFx = 0, ΣFy = 0 at each joint
Method of sections
ΣM = 0 about a cut point
Member force
positive = tension, negative = compression
Method
Find the support reactions for the whole truss.
Method of joints: start at a joint with at most two unknown member forces and use ΣFx = 0 and ΣFy = 0.
Method of sections: cut through the member you need and take moments about a point where the other unknown members meet.
Assume tension; a negative answer means compression.
Frames & machines
Equilibrium of each member
ΣFx = 0, ΣFy = 0, ΣM = 0
Two-force member
force along the line through its two pins
Pin force
equal and opposite on the two members it joins
Magnitude of a pin force
F = √(Fx² + Fy²)
Lever, pliers, bell crank
Fin·a = Fout·b
Toggle
Flink = F/(2 sin θ), Q = F/(2 tan θ)
Uniform load
resultant w·L at the middle of the load
Method
Draw the whole structure and find the support reactions if there are no more than three unknowns.
Spot the two-force members: loaded only at two pins, their force acts along the line between the pins.
Take the frame apart and draw every member on its own, with equal and opposite pin forces where members meet.
For each member, take moments about a pin with unknown forces, then use ΣFx = 0 and ΣFy = 0; combine components into a magnitude at the end.
Shear force & bending moment
Shear and moment
V = ΣF on one side, M = ΣF·d on one side
Bending stress
σ = M·y/I
Rectangle
I = bh³/12
Section modulus
W = I/ymax
Simply supported, uniform load
Mmax = wL²/8
Method
Find the support reactions from equilibrium of the whole beam.
Cut the beam at the section you need and keep one side.
Shear force: sum of the vertical forces on that side. Bending moment: sum of their moments about the cut.
For the maximum moment, find where the shear force is zero.
Centroid & second moment of area
Centroid
ȳ = ΣAiyi/ΣAi
Rectangle
I = bh³/12
Parallel-axis theorem
I = Ic + A·d²
Composite section
I = Σ(Ic,i + Aidi²)
2Practice problems
1.Vectors: dot & cross productMedium
Find the scalar projection compb a of a = (3, −1, −6) onto b = (5, −4, 5), that is, the component of a in the direction of b.
a = (3, −1, −6)b = (5, −4, 5)
compb a =
2.Vectors: dot & cross productHard
Find the area A of the triangle with corners A(2, 2, 0), B(0, 4, 2) and C(1, 2, −3). Coordinates are in metres.
A(2, 2, 0)B(0, 4, 2)C(1, 2, −3)
A = m²
3.Beam support reactionsMedium
The simply supported beam has a pin at A and a roller at B. Find the vertical support reaction RB.
L = 8 mP1 = 40 kN at 1 mP2 = 40 kN at 2 m
RB = kN
4.Beam support reactionsHard
The beam has a pin at A and a roller at B, 5 m from A, and overhangs B to the free end C. It carries a point load P at 2 m from A and a uniformly distributed load w from 3 m to the free end at 8 m. Find the vertical reaction RB, taking upward as positive.
AB = 5 mAC = 8 mP = 60 kN at 2 mw = 3 kN/m from 3 to 8 m
RB = kN
5.Truss: method of jointsMedium
Use the method of joints to find the force FBC in member BC. Give tension as positive and compression as negative.
span = 4 mheight = 2 mB is 1 m from Avertical load = 20 kN
FBC = kN
6.Truss: method of jointsHard
Use the method of joints to find the force FBC in member BC. Give tension as positive and compression as negative.
span = 8 mheight = 4 mB is 6 m from Avertical load = 10 kNhorizontal load = 25 kN ←
FBC = kN
7.Frames & machinesMedium
A horizontal beam AB is pinned to a wall at A and propped by the strut CD, pinned to the wall at C, 1.2 m below A. A load of 3 kN hangs at B. Neglect the weights. Find the magnitude of the pin force A on the beam at A.
P = 3 kNAD = 1.6 mAB = 3 mAC = 1.2 m
A = kN
8.Frames & machinesHard
The beam AB of the wall bracket shown is pinned at A and propped by the strut CD (C is 1.5 m below A). The beam carries a uniform load of 1 kN/m over its full length and a point load of 4 kN at its free end B. Find the force FCD in the strut.
w = 1 kN/mP = 4 kNAD = 0.8 mAB = 2.4 mAC = 1.5 m
FCD = kN
9.Shear force & bending momentMedium
Find the bending moment Mx at the section x = 2 m from support A. Use sagging moments positive and upward shear on the left face positive.
L = 10 mw = 10 kN/m from 0 to 10 mx = 2 m
Mx = kN·m
10.Shear force & bending momentHard
Find the bending moment Mx at the section x = 3.5 m from support A. Use sagging moments positive and upward shear on the left face positive.
L = 10 mP = 35 kN at 2 mw = 12 kN/m from 0 to 10 mx = 3.5 m
Mx = kN·m
11.Centroid & second moment of areaMedium
A channel section lies with its open side up: a base plate 280 mm wide with two upright legs, 100 mm high overall. Base and legs are all 8 mm thick. Find the height ȳ of the centroid above the bottom edge.
b = 280 mmh = 100 mmt = 8 mm
ȳ = mm
12.Centroid & second moment of areaHard
The T-section is used as a beam with the flange on top and carries a sagging bending moment of 15 kN·m. Find the size of the bending stress σtop at the top edge.
Dot product:a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.
Dot product
a·b = 3·5 + (−1)·(−4) + (−6)·5 = −11
Length of b
|b| = √(5² + (−4)² + 5²) = 8.124
Scalar projection
compb a = a·b/|b| = −11/8.124 = −1.354
Answer
compb a = −1.354
Negative: a has a component pointing against b.
2.Vectors: dot & cross product
Answer: A = 5.099 m²
Cross product:a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.
Free-body diagram
Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.
Equilibrium
Moments about A, counter-clockwise positive. Then vertical force balance.
ΣMA = 0: RB·8 = 40·1 + 40·2
RB = 120/8 = 15 kN
ΣFy = 0: RA = 80 − 15 = 65 kN
Answer
RB = 15 kN
4.Beam support reactions
Answer: RB = 40.5 kN
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Replace each distributed load by its resultant (its area) acting at the centroid of the load diagram, and take moments about a support to remove that support’s reaction from the equation.
Resultant of the distributed load
W = 3·5 = 15 kN, x̄ = (3 + 8)/2 = 5.5 m
Equilibrium
Moments about A, counter-clockwise positive. Then vertical force balance.
ΣMA = 0: RB·5 = 60·2 + 15·5.5
RB = 202.5/5 = 40.5 kN
RA = 75 − 40.5 = 34.5 kN
Answer
RB = 40.5 kN
5.Truss: method of joints
Answer: FBC = −9.014 kN
Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.
Support reactions
Equilibrium of the whole truss. Moments about A, counter-clockwise positive.
ΣMA = 0: Cy·4 = 20·1 → Cy = 5 kN
ΣFy = 0: Ay = 20 − 5 = 15 kN
Joint C
The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.
sin γ = 2/3.606 = 0.5547, cos γ = 3/3.606 = 0.8321
Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.
Support reactions
Equilibrium of the whole truss. Moments about A, counter-clockwise positive.
ΣMA = 0: Cy·8 = 10·6 − 25·4 → Cy = −5 kN
ΣFy = 0: Ay = 10 − −5 = 15 kN
ΣFx = 0: Ax = 25 kN
Joint C
The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.
sin γ = 4/4.472 = 0.8944, cos γ = 2/4.472 = 0.4472
Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.
Strut force
FCD = 3·3/(0.6·1.6) = 9.375 kN
Components at A
Ax = FCD·cos α = 7.5 kN (towards the wall)
Ay = 3 − FCD·sin α = −2.625 kN
Magnitude
A = √(7.5² + −2.625²) = 7.946 kN
Answer
A = 7.946 kN
A negative Ay means the wall pulls the beam down at A.
8.Frames & machines
Answer: FCD = 17.68 kN
Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.
Resultant of the uniform load
w·L = 1·2.4 = 2.4 kN at 1.2 m
Moments about A for the beam
FCD·0.8824·0.8 = 2.4·1.2 + 4·2.4 = 12.48 kN·m
FCD = 17.68 kN
Answer
FCD = 17.68 kN
9.Shear force & bending moment
Answer: Mx = 80 kN·m
Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.
Support reactions
Equilibrium of the whole beam.
UDL resultant: W = w·ℓ = 10·10 = 100 kN, acting at x̄ = 5 m
ΣMA = 0: RB·10 = 10·10·5
RB = 500/10 = 50 kN
ΣFy = 0: RA = 100 − 50 = 50 kN
Cut at x = 2 m and keep the left part
Only forces left of the cut appear. A UDL portion acts as one force at the middle of that portion.
M = RA·x − (each load left of the cut × its distance to the cut)
Mx = 50·2 − 10·2·1 = 80 kN·m
Answer
Mx = 80 kN·m
10.Shear force & bending moment
Answer: Mx = 182 kN·m
Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.
Support reactions
Equilibrium of the whole beam.
UDL resultant: W = w·ℓ = 12·10 = 120 kN, acting at x̄ = 5 m
ΣMA = 0: RB·10 = 35·2 + 12·10·5
RB = 670/10 = 67 kN
ΣFy = 0: RA = 155 − 67 = 88 kN
Cut at x = 3.5 m and keep the left part
Only forces left of the cut appear. A UDL portion acts as one force at the middle of that portion.
M = RA·x − (each load left of the cut × its distance to the cut)
Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.
Split into rectangles
Take the base at full width and the two legs above it (height h − t), so nothing is counted twice.
base: A1 = 280·8 = 2240 mm², y1 = 4 mm
two legs: A2 = 2·8·92 = 1472 mm², y2 = 8 + 92/2 = 54 mm
Centroid
ȳ = (2240·4 + 1472·54)/3712 = 23.83 mm
Answer
ȳ = 23.83 mm
12.Centroid & second moment of area
Answer: σtop = 20.56 MPa
Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.
Split into two rectangles
Measure every y from the bottom edge.
flange: Af = 280·20 = 5600 mm², yf = 200 + 20/2 = 210 mm