Statics: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Vectors: dot & cross product

Magnitude
|a| = √(ax² + ay² + az²)
Unit vector
û = a/|a|
Components from an angle
Fx = F·cos θ, Fy = F·sin θ
Dot product
a·b = axbx + ayby + azbz = |a||b|cos θ
Scalar projection of a onto b
a·b/|b|
Work
W = F·d
Cross product
a × b = (aybz − azby, azbx − axbz, axby − aybx)
Areas
parallelogram |a × b|, triangle ½|a × b|
Moment about O
MO = r × F, r = A − O
Volume of a parallelepiped
V = |a·(b × c)|

Method

  1. Write every vector in components; for a force given by a magnitude and an angle, use F·cos θ and F·sin θ.
  2. For lengths and directions use the magnitude √(x² + y² + z²) and the unit vector a/|a|.
  3. Use the dot product for angles, projections, perpendicularity and work: a·b = |a||b|cos θ.
  4. Use the cross product for perpendicular vectors, areas and moments: write the three components carefully, keeping the order a × b.

Beam support reactions

Equilibrium
ΣFx = 0, ΣFy = 0, ΣM = 0
Uniform load
resultant w·L at the middle of the load
Moment
M = F·d

Method

  1. Draw a free-body diagram and replace each support by its reactions.
  2. Replace every distributed load by a single force at its centroid.
  3. Take moments about one support to find the reaction at the other.
  4. Use ΣFy = 0 to find the remaining reaction, and check with a second moment equation.

Truss: method of joints

Method of joints
ΣFx = 0, ΣFy = 0 at each joint
Method of sections
ΣM = 0 about a cut point
Member force
positive = tension, negative = compression

Method

  1. Find the support reactions for the whole truss.
  2. Method of joints: start at a joint with at most two unknown member forces and use ΣFx = 0 and ΣFy = 0.
  3. Method of sections: cut through the member you need and take moments about a point where the other unknown members meet.
  4. Assume tension; a negative answer means compression.

Frames & machines

Equilibrium of each member
ΣFx = 0, ΣFy = 0, ΣM = 0
Two-force member
force along the line through its two pins
Pin force
equal and opposite on the two members it joins
Magnitude of a pin force
F = √(Fx² + Fy²)
Lever, pliers, bell crank
Fin·a = Fout·b
Toggle
Flink = F/(2 sin θ), Q = F/(2 tan θ)
Uniform load
resultant w·L at the middle of the load

Method

  1. Draw the whole structure and find the support reactions if there are no more than three unknowns.
  2. Spot the two-force members: loaded only at two pins, their force acts along the line between the pins.
  3. Take the frame apart and draw every member on its own, with equal and opposite pin forces where members meet.
  4. For each member, take moments about a pin with unknown forces, then use ΣFx = 0 and ΣFy = 0; combine components into a magnitude at the end.

Shear force & bending moment

Shear and moment
V = ΣF on one side, M = ΣF·d on one side
Bending stress
σ = M·y/I
Rectangle
I = bh³/12
Section modulus
W = I/ymax
Simply supported, uniform load
Mmax = wL²/8

Method

  1. Find the support reactions from equilibrium of the whole beam.
  2. Cut the beam at the section you need and keep one side.
  3. Shear force: sum of the vertical forces on that side. Bending moment: sum of their moments about the cut.
  4. For the maximum moment, find where the shear force is zero.

Centroid & second moment of area

Centroid
ȳ = ΣAiyi/ΣAi
Rectangle
I = bh³/12
Parallel-axis theorem
I = Ic + A·d²
Composite section
I = Σ(Ic,i + Aidi²)

2Practice problems

1.Vectors: dot & cross productMedium
xyzab

Find the scalar projection compb a of a = (5, 7, −5) onto b = (−6, 3, −5), that is, the component of a in the direction of b.

a = (5, 7, −5)b = (−6, 3, −5)
compb a =
2.Vectors: dot & cross productHard
xyzab

The unit vector n̂ is perpendicular to both a = (2, −4, 2) and b = (−1, −2, 3) and has a positive z-component. Find its y-component n̂y.

a = (2, −4, 2)b = (−1, −2, 3)n̂z > 0
n̂y =
3.Beam support reactionsMedium
P1​ = 55 kNP2​ = 30 kNABRA​ = ?RB​1.5 m0.5 m2 m

The simply supported beam has a pin at A and a roller at B. Find the vertical support reaction RA.

L = 4 mP1 = 55 kN at 1.5 mP2 = 30 kN at 2 m
RA = kN
4.Beam support reactionsHard
w = 8 kN/mP = 55 kNABRA​ = ?RB​1 m5 m

The simply supported beam has a pin at A and a roller at B. Find the vertical support reaction RA.

L = 6 mP = 55 kN at 1 mw = 8 kN/m from 0 to 1 m
RA = kN
5.Truss: method of jointsMedium
ABCDEFGH20 kN30 kN40 kN4 × 4 m3 m

Exactly one member of this truss carries no force under these loads. Which is the zero-force member? Click it in the diagram.

C: 20 kN ↓D: 30 kN ↓G: 40 kN ↓
  1. 1member AB
  2. 2member BC
  3. 3member CD
  4. 4member DE
  5. 5member FG
  6. 6member GH
  7. 7member AF
  8. 8member HE
  9. 9member BF
  10. 10member CG
  11. 11member DH
  12. 12member FC
  13. 13member HC
6.Truss: method of jointsHard
ABBCACACB10 kN15 kN4 m3 m3 m

Use the method of joints to find the force FAB in member AB. Give tension as positive and compression as negative.

span = 4 mheight = 3 mB is 3 m from Avertical load = 10 kNhorizontal load = 15 kN ←
FAB = kN
7.Frames & machinesMedium
OAB100 NQ120 mm150 mmFO​ = ?

The bell crank shown turns about the pin O. A vertical force of 100 N at A (120 mm from O) is balanced by a horizontal force at B (150 mm above O). Find the magnitude of the pin reaction FO.

F = 100 NOA = 120 mmOB = 150 mm
FO = N
8.Frames & machinesHard
15 kN0.5 kN3 m3 mABC

A uniform horizontal boom AB of weight 0.5 kN is pinned to a wall at A and held by a cable from its end B to the point C on the wall, 3 m above A. A load of 15 kN hangs at B. Find the tension T in the cable.

W = 15 kNWb = 0.5 kNAB = 3 mAC = 3 m
T = kN
9.Shear force & bending momentMedium
w = 3 kN/mABsection2.5 m2.5 m

Find the bending moment Mx at the section x = 2.5 m from support A. Use sagging moments positive and upward shear on the left face positive.

L = 5 mw = 3 kN/m from 0 to 5 mx = 2.5 m
Mx = kN·m
10.Shear force & bending momentHard
12 kN/m20 kN30 kNABCDEFG2 m2 m2 m2 m2 m2 m

The marks A to G split the beam into six equal parts. At which mark is the bending moment largest in size, sagging or hogging? Click it in the diagram.

20 kN @ 0 m30 kN @ 12 m12 kN/m, 2–10 m
  1. 1A (x = 0 m)
  2. 2B (x = 2 m)
  3. 3C (x = 4 m)
  4. 4D (x = 6 m)
  5. 5E (x = 8 m)
  6. 6F (x = 10 m)
  7. 7G (x = 12 m)
11.Centroid & second moment of areaMedium
B = 280H = 375t = 6xdimensions in mm

A hollow rectangular (box) section has outer width B = 280 mm, outer height H = 375 mm and a uniform wall thickness t = 6 mm. Find its radius of gyration r about the horizontal centroidal axis.

B = 280 mmH = 375 mmt = 6 mm
r = mm
12.Centroid & second moment of areaHard
150 mm240 mm72 mm60 × 20xIx​ = ?

A 150 mm × 240 mm plate has a rectangular cut-out 60 mm wide and 20 mm high, centred on the vertical centre line with its centre 72 mm above the bottom. Find the second moment of area Ix about the horizontal axis through the centroid.

b = 150 mmh = 240 mmcut-out: 60 × 20 mmhole centre: y = 72 mm
Ix = × 10⁶ mm⁴

3Solutions

1.Vectors: dot & cross product

Answer: compb a = 1.912

Dot product: a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.

Dot product

a·b = 5·(−6) + 7·3 + (−5)·(−5) = 16

Length of b

|b| = √((−6)² + 3² + (−5)²) = 8.367

Scalar projection

compb a = a·b/|b| = 16/8.367 = 1.912

Answer

compb a = 1.912
2.Vectors: dot & cross product

Answer: n̂y = 0.5774

Cross product: a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.

Cross product

(a × b)x = aybz − azby = (−4)·3 − 2·(−2) = −8
(a × b)y = azbx − axbz = 2·(−1) − 2·3 = −8
(a × b)z = axby − aybx = 2·(−2) − (−4)·(−1) = −8

Normalise

The z-component of a × b is negative, so use −(a × b).

|a × b| = √((−8)² + (−8)² + (−8)²) = 13.86
n̂ = −(−8, −8, −8)/13.86 = (0.5774, 0.5774, 0.5774)
n̂y = 0.5774

Answer

n̂y = 0.5774
3.Beam support reactions

Answer: RA = 49.38 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.

P1​ = 55 kNP2​ = 30 kNABRA​RB​1.5 m0.5 m2 m

Free-body diagram

Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.

Equilibrium

Moments about A, counter-clockwise positive. Then vertical force balance.

ΣMA = 0: RB·4 = 55·1.5 + 30·2
RB = 142.5/4 = 35.63 kN
ΣFy = 0: RA = 85 − 35.63 = 49.38 kN

Answer

RA = 49.38 kN
4.Beam support reactions

Answer: RA = 53.17 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.

w = 8 kN/mP = 55 kNABRA​RB​1 m5 m

Free-body diagram

Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.

Equilibrium

Moments about A, counter-clockwise positive. Then vertical force balance.

UDL resultant: W = w·ℓ = 8·1 = 8 kN, acting at x̄ = 0.5 m
ΣMA = 0: RB·6 = 55·1 + 8·1·0.5
RB = 59/6 = 9.833 kN
ΣFy = 0: RA = 63 − 9.833 = 53.17 kN

Answer

RA = 53.17 kN
5.Truss: method of joints

Answer: member BF

Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.

Joint B

AB and BC lie on one straight line and the joint carries no load. Balancing forces across that line leaves only BF.

ΣF⊥ = 0 → FBF = 0

Check with the method of joints

Solving all joints gives these member forces (T = tension, C = compression).

AB: 50 kN (T), BC: 50 kN (T), CD: 70 kN (T), DE: 70 kN (T), FG: 100 kN (C), GH: 100 kN (C), AF: 62.5 kN (C), HE: 87.5 kN (C), BF: 0, CG: 40 kN (C), DH: 30 kN (T), FC: 62.5 kN (T), HC: 37.5 kN (T)

Answer

Zero-force member: BF
6.Truss: method of joints

Answer: FAB = −19.45 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB10 kN15 kNAy​Cy​Ax​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·4 = 10·3 − 15·3 → Cy = −3.75 kN
ΣFy = 0: Ay = 10 − −3.75 = 13.75 kN
ΣFx = 0: Ax = 15 kN

Joint A

Assume every member is in tension (pulling away from the joint). Only AB has a vertical component at A.

sin α = 3/4.243 = 0.7071
ΣFy = 0: Ay + FAB·sin α = 0
FAB = −13.75/0.7071 = −19.45 kN

Answer

FAB = −19.45 kN (compression)
7.Frames & machines

Answer: FO = 128.1 N

Machines: pliers, levers, linkages and clamps turn an input force into a larger or a differently directed output force. Draw one part as a free body and take moments about its pivot: the pin force drops out, and Fin·a = Fout·b gives the mechanical advantage a/b. The pin force then follows from ΣF = 0 on the same part. In a toggle, two links meet at a shallow angle θ; each link is a two-force member, so a small force F at the joint creates large link forces F/(2 sin θ) and a clamping force F/(2 tan θ).

Force at B

Q = 100·120/150 = 80 N

Pin reaction

Ox = 80 N, Oy = 100 N
FO = √(80² + 100²) = 128.1 N

Answer

FO = 128.1 N
8.Frames & machines

Answer: T = 21.57 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Cable angle

BC = √(3² + 3²) = 4.243 m, sin β = 0.7071

Moments about A

T·0.7071·3 = 15·3 + 0.5·1.5
T = 21.57 kN

Answer

T = 21.57 kN
9.Shear force & bending moment

Answer: Mx = 9.375 kN·m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.

Support reactions

Equilibrium of the whole beam.

UDL resultant: W = w·ℓ = 3·5 = 15 kN, acting at x̄ = 2.5 m
ΣMA = 0: RB·5 = 3·5·2.5
RB = 37.5/5 = 7.5 kN
ΣFy = 0: RA = 15 − 7.5 = 7.5 kN
w = 3 kN/mABRA​ = 7.5RB​ = 7.5section2.5 m2.5 m

Cut at x = 2.5 m and keep the left part

Only forces left of the cut appear. A UDL portion acts as one force at the middle of that portion.

M = RA·x − (each load left of the cut × its distance to the cut)
Mx = 7.5·2.5 − 3·2.5·1.25 = 9.375 kN·m

Answer

Mx = 9.375 kN·m
10.Shear force & bending moment

Answer: F (x = 10 m)

Largest bending moment: M changes slope wherever the shear force changes, so its peaks sit where the shear force crosses zero: under a point load, inside a distributed load, or over a support of an overhang. At a fixed support of a cantilever the moment is largest at the wall. Compare the size of M at those places, sagging or hogging.

Support reactions

Take moments about one support, then use the vertical force balance.

R1 = 65.5 kN, R2 = 80.5 kN

Bending moment at every mark

Sum the moments of all forces on one side of the cut. Sagging is positive, hogging negative.

MA = 0, MB = −40, MC = 27, MD = 46, ME = 17, MF = −60 kN·m, MG = 0

Answer

Mark F: MF = −60 kN·m
11.Centroid & second moment of area

Answer: r = 145 mm

Second moment of area: for a rectangle about its own centroidal axis I = bh³/12, and about its base bh³/3 (parallel-axis theorem I = Ic + A·d²). A hole is handled by subtracting its I, as long as both parts share the same axis. The elastic section modulus is S = I/c, where c is the distance to the extreme fibre. The radius of gyration r = √(I/A) is the distance at which the whole area would give the same I; it is used in column buckling.

Net area and second moment of area

b = 268 mm, h = 363 mm
A = BH − bh = 280·375 − 268·363 = 7716 mm²
I = (BH³ − bh³)/12 = 1.622 × 10⁸ mm⁴

Radius of gyration

r = √(I/A) = √(1.622 × 10⁸/7716) = 145 mm

Answer

r = 145 mm
12.Centroid & second moment of area

Answer: Ix = 169.9 × 10⁶ mm⁴

Sections with holes: treat a hole as a negative area. The centroid is ȳ = (A₁y₁ − A₂y₂)/(A₁ − A₂), with A₁, y₁ for the full plate and A₂, y₂ for the hole. For the second moment of area about the centroidal axis, use the parallel-axis theorem for each part and subtract the hole: I = (Ic1 + A₁d₁²) − (Ic2 + A₂d₂²), where d is the distance from each part's own centroid to the axis through ȳ. A rectangle has Ic = bh³/12 and a circle Ic = πd⁴/64.

Centroid

ȳ = (36000·120 − 1200·72)/(36000 − 1200) = 121.7 mm

Full plate about ȳ

150·240³/12 + 36000·−1.655² = 172.9 × 10⁶ mm⁴

Hole about ȳ

60·20³/12 + 1200·−49.66² = 2.999 × 10⁶ mm⁴

Subtract

Ix = 169.9 × 10⁶ mm⁴

Answer

Ix = 169.9 × 10⁶ mm⁴

ExamProblems · examproblems.com/courses/statics