Statics: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Vectors: dot & cross product

Magnitude
|a| = √(ax² + ay² + az²)
Unit vector
û = a/|a|
Components from an angle
Fx = F·cos θ, Fy = F·sin θ
Dot product
a·b = axbx + ayby + azbz = |a||b|cos θ
Scalar projection of a onto b
a·b/|b|
Work
W = F·d
Cross product
a × b = (aybz − azby, azbx − axbz, axby − aybx)
Areas
parallelogram |a × b|, triangle ½|a × b|
Moment about O
MO = r × F, r = A − O
Volume of a parallelepiped
V = |a·(b × c)|

Method

  1. Write every vector in components; for a force given by a magnitude and an angle, use F·cos θ and F·sin θ.
  2. For lengths and directions use the magnitude √(x² + y² + z²) and the unit vector a/|a|.
  3. Use the dot product for angles, projections, perpendicularity and work: a·b = |a||b|cos θ.
  4. Use the cross product for perpendicular vectors, areas and moments: write the three components carefully, keeping the order a × b.

Beam support reactions

Equilibrium
ΣFx = 0, ΣFy = 0, ΣM = 0
Uniform load
resultant w·L at the middle of the load
Moment
M = F·d

Method

  1. Draw a free-body diagram and replace each support by its reactions.
  2. Replace every distributed load by a single force at its centroid.
  3. Take moments about one support to find the reaction at the other.
  4. Use ΣFy = 0 to find the remaining reaction, and check with a second moment equation.

Truss: method of joints

Method of joints
ΣFx = 0, ΣFy = 0 at each joint
Method of sections
ΣM = 0 about a cut point
Member force
positive = tension, negative = compression

Method

  1. Find the support reactions for the whole truss.
  2. Method of joints: start at a joint with at most two unknown member forces and use ΣFx = 0 and ΣFy = 0.
  3. Method of sections: cut through the member you need and take moments about a point where the other unknown members meet.
  4. Assume tension; a negative answer means compression.

Frames & machines

Equilibrium of each member
ΣFx = 0, ΣFy = 0, ΣM = 0
Two-force member
force along the line through its two pins
Pin force
equal and opposite on the two members it joins
Magnitude of a pin force
F = √(Fx² + Fy²)
Lever, pliers, bell crank
Fin·a = Fout·b
Toggle
Flink = F/(2 sin θ), Q = F/(2 tan θ)
Uniform load
resultant w·L at the middle of the load

Method

  1. Draw the whole structure and find the support reactions if there are no more than three unknowns.
  2. Spot the two-force members: loaded only at two pins, their force acts along the line between the pins.
  3. Take the frame apart and draw every member on its own, with equal and opposite pin forces where members meet.
  4. For each member, take moments about a pin with unknown forces, then use ΣFx = 0 and ΣFy = 0; combine components into a magnitude at the end.

Shear force & bending moment

Shear and moment
V = ΣF on one side, M = ΣF·d on one side
Bending stress
σ = M·y/I
Rectangle
I = bh³/12
Section modulus
W = I/ymax
Simply supported, uniform load
Mmax = wL²/8

Method

  1. Find the support reactions from equilibrium of the whole beam.
  2. Cut the beam at the section you need and keep one side.
  3. Shear force: sum of the vertical forces on that side. Bending moment: sum of their moments about the cut.
  4. For the maximum moment, find where the shear force is zero.

Centroid & second moment of area

Centroid
ȳ = ΣAiyi/ΣAi
Rectangle
I = bh³/12
Parallel-axis theorem
I = Ic + A·d²
Composite section
I = Σ(Ic,i + Aidi²)

2Practice problems

1.Vectors: dot & cross productMedium
xyzab

Find the dot product a·b of a = (−7, 0, 4) and b = (4, 5, 4).

a = (−7, 0, 4)b = (4, 5, 4)
a·b =
2.Vectors: dot & cross productHard
xyzab

For a = (6, 5, −1) and b = (−4, −2, 1), find the z-component (a × b)z of the cross product a × b.

a = (6, 5, −1)b = (−4, −2, 1)
(a × b)z =
3.Beam support reactionsMedium
P1​ = 15 kNP2​ = 15 kNABRA​ = ?RB​2 m1 m5 m

The simply supported beam has a pin at A and a roller at B. Find the vertical support reaction RA.

L = 8 mP1 = 15 kN at 2 mP2 = 15 kN at 3 m
RA = kN
4.Beam support reactionsHard
w = 2 kN/mP = 30 kNABRA​RB​ = ?2 m1 m1 m

The simply supported beam has a pin at A and a roller at B. Find the vertical support reaction RB.

L = 4 mP = 30 kN at 3 mw = 2 kN/m from 2 to 4 m
RB = kN
5.Truss: method of jointsMedium
ABBCACACB40 kN5 m1 m2 m

Use the method of joints to find the force FAB in member AB. Give tension as positive and compression as negative.

span = 5 mheight = 2 mB is 1 m from Avertical load = 40 kN
FAB = kN
6.Truss: method of jointsHard
ABBCACACB20 kN30 kN8 m3 m3 m

Use the method of joints to find the force FAB in member AB. Give tension as positive and compression as negative.

span = 8 mheight = 3 mB is 3 m from Avertical load = 20 kNhorizontal load = 30 kN ←
FAB = kN
7.Frames & machinesMedium
6 kN8 m4 m4.8 mABCK

The frame shown has pins at A, B and C; A and C are fixed to the ground 8 m apart, and B is 4 m above the ground and 4.8 m to the right of A. A vertical load of 6 kN acts on member AB at K, 3.6 m (horizontally) from A. Find the force FBC in member BC.

P = 6 kNL = 8 mH = 4 mhorizontal distance A to B = 4.8 mhorizontal distance A to K = 3.6 m
FBC = kN
8.Frames & machinesHard
5 kN10 kN3 m2 m1.35 mABCK

The frame shown has pins at A, B and C; A and C are fixed to the ground 3 m apart, and B is 2 m high and 1.35 m to the right of A. Member AB carries a vertical load of 5 kN at K, 0.54 m (horizontally) from A, and a horizontal load of 10 kN to the right acts at B on member AB. Find the size of the horizontal reaction Ax at A.

P = 5 kNQ = 10 kNL = 3 mH = 2 mhorizontal distance A to B = 1.35 mhorizontal distance A to K = 0.54 m
Ax = kN
9.Shear force & bending momentMedium
w = 12 kN/mABsection2 m8 m

Find the bending moment Mx at the section x = 2 m from support A. Use sagging moments positive and upward shear on the left face positive.

L = 10 mw = 12 kN/m from 0 to 10 mx = 2 m
Mx = kN·m
10.Shear force & bending momentHard
w = 3 kN/mP = 40 kNABsection3 m1.5 m1.5 m

Find the bending moment Mx at the section x = 4.5 m from support A. Use sagging moments positive and upward shear on the left face positive.

L = 6 mP = 40 kN at 3 mw = 3 kN/m from 0 to 6 mx = 4.5 m
Mx = kN·m
11.Centroid & second moment of areaMedium
xD = 300d = 268dimensions in mm

A circular tube has outside diameter D = 300 mm and inside diameter d = 268 mm. Find its radius of gyration r about the horizontal centroidal axis.

D = 300 mmd = 268 mm
r = mm
12.Centroid & second moment of areaHard
1004601214xM = 120 kN·mdimensions in mm

A symmetric I-section has flanges 100 mm wide and 12 mm thick, an overall depth of 460 mm and a web 14 mm thick. It carries a bending moment of 120 kN·m about the axis x. Find the size of the bending stress σj at the junction of the web and the top flange.

B = 100 mmH = 460 mmtf = 12 mmtw = 14 mmM = 120 kN·m
σj = MPa

3Solutions

1.Vectors: dot & cross product

Answer: a·b = −12

Dot product: a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.

Multiply matching components and add

a·b = (−7)·4 + 0·5 + 4·4 = (−28) + 0 + 16 = −12

Answer

a·b = −12

Negative: the angle between the vectors is more than 90°.

2.Vectors: dot & cross product

Answer: (a × b)z = 8

Cross product: a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.

Cross product, component by component

(a × b)x = aybz − azby = 5·1 − (−1)·(−2) = 3
(a × b)y = azbx − axbz = (−1)·(−4) − 6·1 = −2
(a × b)z = axby − aybx = 6·(−2) − 5·(−4) = 8

Requested component

(a × b)z = 8

Answer

(a × b)z = 8

Check: a × b is perpendicular to both vectors, so its dot product with a and with b is zero.

3.Beam support reactions

Answer: RA = 20.63 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.

P1​ = 15 kNP2​ = 15 kNABRA​RB​2 m1 m5 m

Free-body diagram

Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.

Equilibrium

Moments about A, counter-clockwise positive. Then vertical force balance.

ΣMA = 0: RB·8 = 15·2 + 15·3
RB = 75/8 = 9.375 kN
ΣFy = 0: RA = 30 − 9.375 = 20.63 kN

Answer

RA = 20.63 kN
4.Beam support reactions

Answer: RB = 25.5 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.

w = 2 kN/mP = 30 kNABRA​RB​2 m1 m1 m

Free-body diagram

Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.

Equilibrium

Moments about A, counter-clockwise positive. Then vertical force balance.

UDL resultant: W = w·ℓ = 2·2 = 4 kN, acting at x̄ = 3 m
ΣMA = 0: RB·4 = 30·3 + 2·2·3
RB = 102/4 = 25.5 kN
ΣFy = 0: RA = 34 − 25.5 = 8.5 kN

Answer

RB = 25.5 kN
5.Truss: method of joints

Answer: FAB = −35.78 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB40 kNAy​Cy​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·5 = 40·1 → Cy = 8 kN
ΣFy = 0: Ay = 40 − 8 = 32 kN

Joint A

Assume every member is in tension (pulling away from the joint). Only AB has a vertical component at A.

sin α = 2/2.236 = 0.8944
ΣFy = 0: Ay + FAB·sin α = 0
FAB = −32/0.8944 = −35.78 kN

Answer

FAB = −35.78 kN (compression)
6.Truss: method of joints

Answer: FAB = −33.59 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB20 kN30 kNAy​Cy​Ax​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·8 = 20·3 − 30·3 → Cy = −3.75 kN
ΣFy = 0: Ay = 20 − −3.75 = 23.75 kN
ΣFx = 0: Ax = 30 kN

Joint A

Assume every member is in tension (pulling away from the joint). Only AB has a vertical component at A.

sin α = 3/4.243 = 0.7071
ΣFy = 0: Ay + FAB·sin α = 0
FAB = −23.75/0.7071 = −33.59 kN

Answer

FAB = −33.59 kN (compression)
7.Frames & machines

Answer: FBC = 3.458 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Two-force member BC

BC = √(3.2² + 4²) = 5.122 m

Whole frame: moments about A

The ground pushes on BC at C along CB; its horizontal component passes through A, only the vertical one has a moment.

FBC·(4/5.122)·8 = 6·3.6
FBC = 3.458 kN (compression)

Answer

FBC = 3.458 kN
8.Frames & machines

Answer: Ax = 3.757 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Direction of BC

BC = 2.593 m, cos = 0.6364, sin = 0.7714

Whole frame: moments about A

FBC·0.7714·3 = 5·0.54 + 10·2
FBC = 9.809 kN

Horizontal balance

Ax + 10 − 9.809·0.6364 = 0
Ax = −3.757 kN → |Ax| = 3.757 kN

Answer

Ax = 3.757 kN

The minus sign means Ax points to the left.

9.Shear force & bending moment

Answer: Mx = 96 kN·m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.

Support reactions

Equilibrium of the whole beam.

UDL resultant: W = w·ℓ = 12·10 = 120 kN, acting at x̄ = 5 m
ΣMA = 0: RB·10 = 12·10·5
RB = 600/10 = 60 kN
ΣFy = 0: RA = 120 − 60 = 60 kN
w = 12 kN/mABRA​ = 60RB​ = 60section2 m8 m

Cut at x = 2 m and keep the left part

Only forces left of the cut appear. A UDL portion acts as one force at the middle of that portion.

M = RA·x − (each load left of the cut × its distance to the cut)
Mx = 60·2 − 12·2·1 = 96 kN·m

Answer

Mx = 96 kN·m
10.Shear force & bending moment

Answer: Mx = 40.13 kN·m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.

Support reactions

Equilibrium of the whole beam.

UDL resultant: W = w·ℓ = 3·6 = 18 kN, acting at x̄ = 3 m
ΣMA = 0: RB·6 = 40·3 + 3·6·3
RB = 174/6 = 29 kN
ΣFy = 0: RA = 58 − 29 = 29 kN
w = 3 kN/mP = 40 kNABRA​ = 29RB​ = 29section3 m1.5 m1.5 m

Cut at x = 4.5 m and keep the left part

Only forces left of the cut appear. A UDL portion acts as one force at the middle of that portion.

M = RA·x − (each load left of the cut × its distance to the cut)
Mx = 29·4.5 − 40·(4.5 − 3) − 3·4.5·2.25 = 40.13 kN·m

Answer

Mx = 40.13 kN·m
11.Centroid & second moment of area

Answer: r = 100.6 mm

Second moment of area: for a rectangle about its own centroidal axis I = bh³/12, and about its base bh³/3 (parallel-axis theorem I = Ic + A·d²). A hole is handled by subtracting its I, as long as both parts share the same axis. The elastic section modulus is S = I/c, where c is the distance to the extreme fibre. The radius of gyration r = √(I/A) is the distance at which the whole area would give the same I; it is used in column buckling.

Net area and second moment of area

A = π(D² − d²)/4 = 14275 mm²
I = π(D⁴ − d⁴)/64 = 1.444 × 10⁸ mm⁴

Radius of gyration

r = √(I/A) = √(1.444 × 10⁸/14275) = 100.6 mm

Answer

r = 100.6 mm
12.Centroid & second moment of area

Answer: σj = 120.5 MPa

Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.

Outer rectangle minus the two side cut-outs

Both cut-outs together are (B − tw) wide and hw = H − 2tf high, and share the axis x.

hw = 460 − 2·12 = 436 mm
Ix = (B·H³ − (B − tw)·hw³)/12 = (100·460³ − 86·436³)/12
Ix = 2.171 × 10⁸ mm⁴

Bending stress

y = 230 − 12 = 218 mm
σ = M·y/I = 1.2 × 10⁸·218/2.171 × 10⁸ = 120.5 MPa

Answer

σj = 120.5 MPa

ExamProblems · examproblems.com/courses/statics